Koetsu Yamazaki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Koetsu Yamazaki has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Jing Han
11 shared publicationsRyoichi Itoh
Universal Can Corporation
4 shared publicationsSadao Nishiyama
3 shared publications- Takanori Chihara
Institute of Science and Engineering, Kanazawa University, Kanazawa 920-1192, Japan
2 shared publications - Jing Han
Technical Development Department, Aluminum Company, Mitsubishi Materials Corporation, Shizuoka, Japan
1 shared publication Kotaro Shimada
1 shared publication
Latest Publications
- 1 November 2011
- Published by Wiley in Journal of Mechanical Design
- Vol. 133 (11) , 114502
Tooling System Design for Forming Aluminum Beverage Can End Shells
This paper proposes a new tooling system and performs an optimum design on it to minimize the amount of thinning during a forming process of aluminum beverage can end shells. Numerical simulations of the shell forming process and structural performance of the shell under internal pressure have been performed. Influences of the upmost surface profiles and initial positions of the tool in the new tooling system on the shell forming quality have been investigated, and a structural optimization method based on the numerical simulations has been then applied to find optimum design points subject to constraints of the shell geometrical dimensions. A comparison shows that thinning of the shell formed by the proposed new tooling system can be reduced approximately 3.6% compared to a conventional tooling system. Optimization results of the new tooling system show that the amount of thinning can be reduced almost 4%. It is also confirmed that the buckle pressure resistance of the shell is improved 5.5%. The new tooling system may reduce the amount of thinning; hence, may improve the structural performance of the can and may save metal.
- 1 November 2011
- Published by Wiley in Journal of Mechanical Design
- Vol. 133 (11) , 114502
Tooling System Design for Forming Aluminum Beverage Can End Shells
This paper proposes a new tooling system and performs an optimum design on it to minimize the amount of thinning during a forming process of aluminum beverage can end shells. Numerical simulations of the shell forming process and structural performance of the shell under internal pressure have been performed. Influences of the upmost surface profiles and initial positions of the tool in the new tooling system on the shell forming quality have been investigated, and a structural optimization method based on the numerical simulations has been then applied to find optimum design points subject to constraints of the shell geometrical dimensions. A comparison shows that thinning of the shell formed by the proposed new tooling system can be reduced approximately 3.6% compared to a conventional tooling system. Optimization results of the new tooling system show that the amount of thinning can be reduced almost 4%. It is also confirmed that the buckle pressure resistance of the shell is improved 5.5%. The new tooling system may reduce the amount of thinning; hence, may improve the structural performance of the can and may save metal.
- 1 January 2008
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C
- Vol. 74 (738) , 475-483
A Study on Openability of an Aluminum Beverage Bottle
- 1 January 2008
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C
- Vol. 74 (738) , 475-483
A Study on Openability of an Aluminum Beverage Bottle
- 1 January 2007
- Published by Japan Society of Mechanical Engineers in The Proceedings of Design & Systems Conference
- Vol. 2007.17, 40-41
1203 A Study on Openability of Aluminum Beverage Bottle
- 1 January 2007
- Published by Japan Society of Mechanical Engineers in The Proceedings of Design & Systems Conference
- Vol. 2007.17, 40-41
1203 A Study on Openability of Aluminum Beverage Bottle
- 1 January 2007
- Published by ASME International
- p. 405-411
Evaluation Method of Drinking Ease for Aluminum Beverage Bottles
This paper has investigated effects of the bottle opening size on drinking feelings in order to improve the comfort level of consumers when drinking directly from the opening of aluminum bottle. A survey over 120 subjects has been performed based on a drinking test using three kinds of bottles with opening diameters of 28, 33 and 38 mm, respectively. Two questionnaires have been conducted. Statistical analysis results of Questionnaire 1 have shown that 33-mm opening is best for adult consumers with no matter the type of contents, gender and the mouth size. The factor analysis results of Questionnaire 2 based on Kansei Engineering have shown that drinking feeling is affected by two common factors, which considered as the flow from the bottle to the mouth and the flow adjustability. Moreover, the fluid-dynamics analysis model has been developed to simulate the bottled liquid in a drinking action consisting of survey results and experimental observations of consumers’ drinking actions. Numerical simulations have been performed to understand how consumers control the flow during the drinking actions. It is found that the consumers usually try to realize the ideal and preferable condition by adjusting the inclination angle of the bottle.
- 1 January 2007
- Published by ASME International
- p. 405-411
Evaluation Method of Drinking Ease for Aluminum Beverage Bottles
This paper has investigated effects of the bottle opening size on drinking feelings in order to improve the comfort level of consumers when drinking directly from the opening of aluminum bottle. A survey over 120 subjects has been performed based on a drinking test using three kinds of bottles with opening diameters of 28, 33 and 38 mm, respectively. Two questionnaires have been conducted. Statistical analysis results of Questionnaire 1 have shown that 33-mm opening is best for adult consumers with no matter the type of contents, gender and the mouth size. The factor analysis results of Questionnaire 2 based on Kansei Engineering have shown that drinking feeling is affected by two common factors, which considered as the flow from the bottle to the mouth and the flow adjustability. Moreover, the fluid-dynamics analysis model has been developed to simulate the bottled liquid in a drinking action consisting of survey results and experimental observations of consumers’ drinking actions. Numerical simulations have been performed to understand how consumers control the flow during the drinking actions. It is found that the consumers usually try to realize the ideal and preferable condition by adjusting the inclination angle of the bottle.
- 1 January 2007
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 73 (733) , 1095-1102
Designs of Aluminum Beverage Can Ends Considering the Finger Accessibility When Opening Cans
- 1 January 2007
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 73 (733) , 1095-1102
Designs of Aluminum Beverage Can Ends Considering the Finger Accessibility When Opening Cans
- 1 January 2006
- Published by Japan Society of Mechanical Engineers in The Proceedings of Design & Systems Conference
- Vol. 2006.16, 33-34
1107 Opening Characteristics of an Aluminum Bottle (2nd Report)
- 1 January 2006
- Published by Japan Society of Mechanical Engineers in The Proceedings of Design & Systems Conference
- Vol. 2006.16, 33-34
1107 Opening Characteristics of an Aluminum Bottle (2nd Report)
- 1 January 2005
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 71 (701) , 43-50
Bottom Shape Optimization of Two-piece Aluminum Beverage Bottle by Multilevel Optimization Method
- 1 January 2005
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 71 (701) , 43-50
Bottom Shape Optimization of Two-piece Aluminum Beverage Bottle by Multilevel Optimization Method
- 1 January 2001
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 67 (664) , 1885-1891
Optimization of the Crushing Characteristic of Triangulated Cans.
- 1 January 2001
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 67 (664) , 1885-1891
Optimization of the Crushing Characteristic of Triangulated Cans.