Jing Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jing Han has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Koetsu Yamazaki
Kanazawa University, Kanazawa, Japan
4 shared publications S. Nishiyama
Aluminum Company, Mitsubishi Materials Corporation
2 shared publicationsAkiyoshi Matsuzaki
Universal Can Corporation
1 shared publicationKoetsu Yamazaki
Kanazawa University
1 shared publication- Koetsu Yamazaki
Kanazawa University
1 shared publication R. Itoh
Aluminum Company, Mitsubishi Materials Corporation
1 shared publication
Latest Publications
- 6 December 2017
- Published by Springer Nature
- p. 2063-2075
Optimum Design on Neck Embossing Decoration of Aluminum Beverage Bottles
- 6 December 2017
- Published by Springer Nature
- p. 2063-2075
Optimum Design on Neck Embossing Decoration of Aluminum Beverage Bottles
- 1 November 2011
- Published by Wiley in Journal of Mechanical Design
- Vol. 133 (11) , 114502
Tooling System Design for Forming Aluminum Beverage Can End Shells
This paper proposes a new tooling system and performs an optimum design on it to minimize the amount of thinning during a forming process of aluminum beverage can end shells. Numerical simulations of the shell forming process and structural performance of the shell under internal pressure have been performed. Influences of the upmost surface profiles and initial positions of the tool in the new tooling system on the shell forming quality have been investigated, and a structural optimization method based on the numerical simulations has been then applied to find optimum design points subject to constraints of the shell geometrical dimensions. A comparison shows that thinning of the shell formed by the proposed new tooling system can be reduced approximately 3.6% compared to a conventional tooling system. Optimization results of the new tooling system show that the amount of thinning can be reduced almost 4%. It is also confirmed that the buckle pressure resistance of the shell is improved 5.5%. The new tooling system may reduce the amount of thinning; hence, may improve the structural performance of the can and may save metal.
- 1 November 2011
- Published by Wiley in Journal of Mechanical Design
- Vol. 133 (11) , 114502
Tooling System Design for Forming Aluminum Beverage Can End Shells
This paper proposes a new tooling system and performs an optimum design on it to minimize the amount of thinning during a forming process of aluminum beverage can end shells. Numerical simulations of the shell forming process and structural performance of the shell under internal pressure have been performed. Influences of the upmost surface profiles and initial positions of the tool in the new tooling system on the shell forming quality have been investigated, and a structural optimization method based on the numerical simulations has been then applied to find optimum design points subject to constraints of the shell geometrical dimensions. A comparison shows that thinning of the shell formed by the proposed new tooling system can be reduced approximately 3.6% compared to a conventional tooling system. Optimization results of the new tooling system show that the amount of thinning can be reduced almost 4%. It is also confirmed that the buckle pressure resistance of the shell is improved 5.5%. The new tooling system may reduce the amount of thinning; hence, may improve the structural performance of the can and may save metal.
- Open Access
- 2 March 2006
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 32 (2) , 141-151
Multiobjective optimization of a two-piece aluminum beverage bottle considering tactile sensation of heat and embossing formability
- 2 March 2006
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 32 (2) , 141-151
Open AccessMultiobjective optimization of a two-piece aluminum beverage bottle considering tactile sensation of heat and embossing formability
- 1 December 2004
- Published by Taylor & Francis in Engineering Optimization
- Vol. 36 (6) , 691-703
A novel technique of shape optimization for the contact parts of bolt–nut fastening structures
This article deals with the shape optimization of the contact part of a bolt–nut fastening structure using a novel technique. In this method, all contact parts are composed as a quasi-continuum structure using a kind of thin film element. The Young modulus of the thin film elements depends on the compressive and tensile states, and is much smaller than that of usual elements. The shape optimization problem of the quasi-continuum structure is then solved by the structural analysis and the optimization software GENESIS. Numerical results of the shape optimization of the bolt-nut fastening structure are given to prove the effectiveness of the new technique. The proposed technique is easy to apply without any additional computational time and code for complex contact analysis.
- 1 December 2004
- Published by Taylor & Francis in Engineering Optimization
- Vol. 36 (6) , 691-703
A novel technique of shape optimization for the contact parts of bolt–nut fastening structures
This article deals with the shape optimization of the contact part of a bolt–nut fastening structure using a novel technique. In this method, all contact parts are composed as a quasi-continuum structure using a kind of thin film element. The Young modulus of the thin film elements depends on the compressive and tensile states, and is much smaller than that of usual elements. The shape optimization problem of the quasi-continuum structure is then solved by the structural analysis and the optimization software GENESIS. Numerical results of the shape optimization of the bolt-nut fastening structure are given to prove the effectiveness of the new technique. The proposed technique is easy to apply without any additional computational time and code for complex contact analysis.
- 26 October 2004
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 29 (4) , 304-311
Application of structure optimization technique to aluminum beverage bottle design
- 26 October 2004
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 29 (4) , 304-311
Application of structure optimization technique to aluminum beverage bottle design
- 6 July 2004
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 28 (1) , 47-54
Optimization of the crushing characteristics of triangulated aluminum beverage cans
- 6 July 2004
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 28 (1) , 47-54
Optimization of the crushing characteristics of triangulated aluminum beverage cans