David L. Ransom
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
David L. Ransom has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- J. Jeffrey Moore
Southwest Research Institute®, San Antonio, TX
5 shared publications Andrew Lerche
Southwest Research Institute®, San Antonio, TX
1 shared publicationDaniel Lubell
Capstone Turbine Corporation, Chatsworth, CA
1 shared publication- Flavia Viana
Mechanical and Materials Engineering Division, Southwest Research Institute®, Post Office Drawer 28510, San Antonio, TX 78228-0510
1 shared publication - Giuseppe Vannini
GE Oil & Gas, Via F. Matteucci, 2, Florence 50127, Italy
1 shared publication - Jason C. Wilkes
Machinery Department, Southwest Research Institute, San Antonio, TX 78238
1 shared publication
Latest Publications
- 12 December 2013
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 136 (4) , 042504
An Improved Catcher Bearing Model and an Explanation of the Forward Whirl/Whip Phenomenon Observed in Active Magnetic Bearing Transient Drop Experiments
Though many approaches have been proposed in the literature to model the reaction forces in a catcher bearing (CB), there are still phenomena observed in experimental tests that cannot be explained by existing models. The following paper presents a novel approach to model a CB system. Some of the elements in the model have been previously introduced in the literature; however, there are other elements in the proposed model that are new, providing an explanation for the forward whirling phenomena that has been observed repeatedly in the literature. The proposed CB model is implemented in a finite-element rotordynamic package, and nonlinear time-transient simulations are performed to predict published experimental results of a high-speed vertical subscale compressor; with no other forces present in the model, the agreement between simulations and experimental data is favorable. The results presented herein show that friction between the journal and axial face of the catcher bearing results in a forward cross-coupled force that pushes the rotor in the direction of rotation. This force is proportional to the coefficient of friction between the axial face of the rotor and catcher bearing and the axial thrust on the rotor. This force results in synchronous whirl when the running speed is below a combined natural frequency of the rotor-stator system and constant frequency whip when the speed is above a whip frequency.
- 12 December 2013
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 136 (4) , 042504
An Improved Catcher Bearing Model and an Explanation of the Forward Whirl/Whip Phenomenon Observed in Active Magnetic Bearing Transient Drop Experiments
Though many approaches have been proposed in the literature to model the reaction forces in a catcher bearing (CB), there are still phenomena observed in experimental tests that cannot be explained by existing models. The following paper presents a novel approach to model a CB system. Some of the elements in the model have been previously introduced in the literature; however, there are other elements in the proposed model that are new, providing an explanation for the forward whirling phenomena that has been observed repeatedly in the literature. The proposed CB model is implemented in a finite-element rotordynamic package, and nonlinear time-transient simulations are performed to predict published experimental results of a high-speed vertical subscale compressor; with no other forces present in the model, the agreement between simulations and experimental data is favorable. The results presented herein show that friction between the journal and axial face of the catcher bearing results in a forward cross-coupled force that pushes the rotor in the direction of rotation. This force is proportional to the coefficient of friction between the axial face of the rotor and catcher bearing and the axial thrust on the rotor. This force results in synchronous whirl when the running speed is below a combined natural frequency of the rotor-stator system and constant frequency whip when the speed is above a whip frequency.
- 19 November 2010
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (4) , 042504
Rotordynamic Force Prediction of Centrifugal Compressor Impellers Using Computational Fluid Dynamics
The energy industry depends on centrifugal compressors to produce, process, reinject, and transport many different gases. Centrifugal compressors use one or more impellers to impart momentum to the flowing gas and, thereby, produce an increase in pressure through diffusion. As the operating pressure in a compressor increases, the fluid-rotor interaction at the seals and impellers become more important. Also, the new generation of megascale liquefied natural gas compressors is dependent on accurate assessment of these forces. The aerodynamic forces and cross-coupled stiffness from the impellers cannot be accurately predicted with traditional methods and must be estimated with semiempirical formulations. The result of these inaccuracies is a potential for compressor designs that can experience unexpected, dangerous, and damaging instabilities and subsynchronous vibrations. The current investigation is intended to advance the state of the art to achieve an improved, physics-based method of predicted aerodynamic destabilizing cross-coupling forces on centrifugal compressor impellers using computational fluid dynamics (CFD). CFD was employed in this study to predict the impeller-fluid interaction forces, which gives rise to the aerodynamic cross coupling. The procedure utilized in this study was developed by Moore and Palazzolo (2002, “Rotordynamic Force Prediction of Centrifugal Impeller Shroud Passages Using Computational Fluid Dynamic Techniques With Combined Primary Secondary Flow Model ,” ASME J. Eng. Gas Turbines Power, 123, pp. 910–918), which applied the method to liquid pump impellers. Their results showed good correlation to test data. Unfortunately, no such data exist for centrifugal compressors. Therefore, in order to validate the present model, comparisons will be made to predict the instability of an industrial centrifugal compressor. A parametric CFD study is then presented leading to a new analytical expression for predicting the cross-coupled stiffness for centrifugal impellers.
- 19 November 2010
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (4) , 042504
Rotordynamic Force Prediction of Centrifugal Compressor Impellers Using Computational Fluid Dynamics
The energy industry depends on centrifugal compressors to produce, process, reinject, and transport many different gases. Centrifugal compressors use one or more impellers to impart momentum to the flowing gas and, thereby, produce an increase in pressure through diffusion. As the operating pressure in a compressor increases, the fluid-rotor interaction at the seals and impellers become more important. Also, the new generation of megascale liquefied natural gas compressors is dependent on accurate assessment of these forces. The aerodynamic forces and cross-coupled stiffness from the impellers cannot be accurately predicted with traditional methods and must be estimated with semiempirical formulations. The result of these inaccuracies is a potential for compressor designs that can experience unexpected, dangerous, and damaging instabilities and subsynchronous vibrations. The current investigation is intended to advance the state of the art to achieve an improved, physics-based method of predicted aerodynamic destabilizing cross-coupling forces on centrifugal compressor impellers using computational fluid dynamics (CFD). CFD was employed in this study to predict the impeller-fluid interaction forces, which gives rise to the aerodynamic cross coupling. The procedure utilized in this study was developed by Moore and Palazzolo (2002, “Rotordynamic Force Prediction of Centrifugal Impeller Shroud Passages Using Computational Fluid Dynamic Techniques With Combined Primary Secondary Flow Model ,” ASME J. Eng. Gas Turbines Power, 123, pp. 910–918), which applied the method to liquid pump impellers. Their results showed good correlation to test data. Unfortunately, no such data exist for centrifugal compressors. Therefore, in order to validate the present model, comparisons will be made to predict the instability of an industrial centrifugal compressor. A parametric CFD study is then presented leading to a new analytical expression for predicting the cross-coupled stiffness for centrifugal impellers.
- 10 October 2010
- Published by ASME International
- p. 541-548
Development of a High Speed Gas Bearing Test Rig to Measure Rotordynamic Force Coefficients
The use of gas bearings has increased over the last several decades to include microturbines, air cycle machines, and hermetically sealed compressors and turbines. Gas bearings have many advantages over traditional bearings, such as rolling element or oil lubricated fluid film bearings, including longer life, ability to use the process fluid, no contamination of the process with lubricants, accommodating high shaft speeds, and operation over a wide range of temperatures. Unlike fluid film bearings that utilize oil, gas lubricated bearings generate very little damping from the gas itself. Therefore, successful bearing designs such as foil bearings utilize damping features on the bearing to improve the damping generated. Similar to oil bearings, gas bearing designers strive to develop gas bearings with good rotordynamic stability. Gas bearings are challenging to design requiring a fully coupled thermo-elastic, hydrodynamic analysis including complex non-linear mechanisms such as Coulomb friction. There is a surprisingly low amount of rotordynamic force coefficient measurement in the literature despite the need to verify the model predictions and the stability of the bearing. This paper describes the development and testing of a 60,000 rpm gas bearing test rig and presents measured stiffness and damping coefficients for a 57 mm foil type bearing. The design of the rig overcomes many challenges in making this measurement by developing a patented, high-frequency, high-amplitude shaker system resulting in excitation over most of the subsynchronous range.
- 10 October 2010
- Published by ASME International
- p. 541-548
Development of a High Speed Gas Bearing Test Rig to Measure Rotordynamic Force Coefficients
The use of gas bearings has increased over the last several decades to include microturbines, air cycle machines, and hermetically sealed compressors and turbines. Gas bearings have many advantages over traditional bearings, such as rolling element or oil lubricated fluid film bearings, including longer life, ability to use the process fluid, no contamination of the process with lubricants, accommodating high shaft speeds, and operation over a wide range of temperatures. Unlike fluid film bearings that utilize oil, gas lubricated bearings generate very little damping from the gas itself. Therefore, successful bearing designs such as foil bearings utilize damping features on the bearing to improve the damping generated. Similar to oil bearings, gas bearing designers strive to develop gas bearings with good rotordynamic stability. Gas bearings are challenging to design requiring a fully coupled thermo-elastic, hydrodynamic analysis including complex non-linear mechanisms such as Coulomb friction. There is a surprisingly low amount of rotordynamic force coefficient measurement in the literature despite the need to verify the model predictions and the stability of the bearing. This paper describes the development and testing of a 60,000 rpm gas bearing test rig and presents measured stiffness and damping coefficients for a 57 mm foil type bearing. The design of the rig overcomes many challenges in making this measurement by developing a patented, high-frequency, high-amplitude shaker system resulting in excitation over most of the subsynchronous range.
- 1 January 2009
- Published by ASME International
- p. 1023-1031
Centrifugal Compressor Stability Prediction Using a New Physics Based Approach
The accurate prediction of centrifugal compressor stability continues to be an important area of interest in the oil and gas industry. Ensuring stability is critical to the cost-effective installation and operation of these machines in remote environments, where field stability problems are much more expensive to diagnose and correct. Current industry standards and tools for the prediction of impeller destabilizing forces are based on empirical methods that, to date, have served fairly well for systems with reasonable stability margins. However, as stability margins are decreased, use of a modeling method that is more physics based and can better represent the observed trends in machine behavior at low stability margins is required. Furthermore, the development of mega-class Liquefied Natural Gas (LNG) compressors and ultra-high pressure reinjection compressors provides further motivation to improve accuracy. In this paper, a new physics based expression for the prediction of impeller cross-coupling, previously described by Moore, et al. [1] is further investigated by analyzing several classes and scale factors of impellers ranging from 2-D designs used in reinjection to full 3-D impellers typically used in LNG. The new expression is based on both Computational Fluid Dynamics (CFD) simulation and experimental test data from a known instability. These results are then applied to two case studies of marginally stable and unstable compressors in the field that were studied by the authors’ company. For each case study, the system stability is evaluated using both the new physics based expression as well as the more traditional empirical approaches. Comparisons are made for overall stability prediction as well as sensitivity to system changes. Conclusions are made regarding the applicability and limits of this new approach.
- 1 January 2009
- Published by ASME International
- p. 1023-1031
Centrifugal Compressor Stability Prediction Using a New Physics Based Approach
The accurate prediction of centrifugal compressor stability continues to be an important area of interest in the oil and gas industry. Ensuring stability is critical to the cost-effective installation and operation of these machines in remote environments, where field stability problems are much more expensive to diagnose and correct. Current industry standards and tools for the prediction of impeller destabilizing forces are based on empirical methods that, to date, have served fairly well for systems with reasonable stability margins. However, as stability margins are decreased, use of a modeling method that is more physics based and can better represent the observed trends in machine behavior at low stability margins is required. Furthermore, the development of mega-class Liquefied Natural Gas (LNG) compressors and ultra-high pressure reinjection compressors provides further motivation to improve accuracy. In this paper, a new physics based expression for the prediction of impeller cross-coupling, previously described by Moore, et al. [1] is further investigated by analyzing several classes and scale factors of impellers ranging from 2-D designs used in reinjection to full 3-D impellers typically used in LNG. The new expression is based on both Computational Fluid Dynamics (CFD) simulation and experimental test data from a known instability. These results are then applied to two case studies of marginally stable and unstable compressors in the field that were studied by the authors’ company. For each case study, the system stability is evaluated using both the new physics based expression as well as the more traditional empirical approaches. Comparisons are made for overall stability prediction as well as sensitivity to system changes. Conclusions are made regarding the applicability and limits of this new approach.
- 1 January 2008
- Published by ASME International
- p. 1305-1309
Refinement of Physics Based Approach Used in the Prediction of Impeller Rotordynamic Forces for Centrifugal Compressors
The accurate prediction of centrifugal compressor stability continues to be an important area of interest in the oil and gas industry. Ensuring stability is critical to the cost-effective installation and operation of these machines in remote environments where field stability problems are much more expensive to diagnose and correct. Current industry standards and tools for the prediction of impeller destabilizing forces are based on empirical methods that, to date, have served fairly well for systems with reasonable stability margins. However, as stability margins are decreased, use of a modeling method that is more physics based that can better represent the observed trends in machine behavior at low stability margins is needed. Furthermore, the development of mega-class Liquefied Natural Gas (LNG) compressors and ultra-high pressure re-injection compressors provide further motivation to improve accuracy. In this paper, a new physics based expression for the prediction of impeller cross-coupling, previously introduced by Moore et al. [1] is further investigated by analyzing several classes and scale factors of impellers ranging from 2-D designs used in re-injection up to full 3-D impellers typically used in LNG. The new expression is based on both numerical simulation (CFD) and experimental test data from a known instability. Comparisons are made for overall stability prediction as well as sensitivity to system changes. Conclusions are made regarding the applicability and limits of this new approach.
- 1 January 2008
- Published by ASME International
- p. 1305-1309
Refinement of Physics Based Approach Used in the Prediction of Impeller Rotordynamic Forces for Centrifugal Compressors
The accurate prediction of centrifugal compressor stability continues to be an important area of interest in the oil and gas industry. Ensuring stability is critical to the cost-effective installation and operation of these machines in remote environments where field stability problems are much more expensive to diagnose and correct. Current industry standards and tools for the prediction of impeller destabilizing forces are based on empirical methods that, to date, have served fairly well for systems with reasonable stability margins. However, as stability margins are decreased, use of a modeling method that is more physics based that can better represent the observed trends in machine behavior at low stability margins is needed. Furthermore, the development of mega-class Liquefied Natural Gas (LNG) compressors and ultra-high pressure re-injection compressors provide further motivation to improve accuracy. In this paper, a new physics based expression for the prediction of impeller cross-coupling, previously introduced by Moore et al. [1] is further investigated by analyzing several classes and scale factors of impellers ranging from 2-D designs used in re-injection up to full 3-D impellers typically used in LNG. The new expression is based on both numerical simulation (CFD) and experimental test data from a known instability. Comparisons are made for overall stability prediction as well as sensitivity to system changes. Conclusions are made regarding the applicability and limits of this new approach.