JMJ. Jeffrey Moore

J. Jeffrey Moore

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


J. Jeffrey Moore has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Oxygen Storage Incorporated Into Net Power and the Allam–Fetvedt Oxy-Fuel sCO2 Power Cycle—Techno-Economic Analysis

    by J. Jeffrey Moore, Owen Pryor, Ian Cormier, Jeremy Fetvedt

    With the planned future reliance on variable renewable energy, the ability to store energy for prolonged time periods will be required to reduce the disruption of market fluctuations. This paper presents a method to analyze a hybrid liquid-oxygen (LOx) storage / direct-fired sCO2 power cycle and optimize the economic performance over a diverse range of scenarios. The system utilizes a modified version of the NET Power process to produce energy when energy demand exceeds the supply while displacing much of the cost of the ASU energy requirements through cryogenic storage of oxygen. The model uses marginal cost of energy data to determine the optimal times to charge and discharge the system over a given scenario. The model then applies ramp rates and other time-dependent factors to generate an economic model for the system without storage considerations. The size of the storage system is then applied to create a realistic model of the plant operation. From the real plant operation model, the amount of energy charged and discharged, the CAPEX of each system, energy costs and revenue and other parameters can be calculated. The economic parameters are then combined to calculate the net present value (NPV) of the system for the given scenario. The model was then run through the SMPSO genetic algorithm in Python for a variety of geographic regions and large-scale scenarios (high solar penetration) to maximize the NPV based on multiple parameters for each subsystem. The LOx storage requirements will also be discussed.


  • Manufacturing and Hydro Testing of a 10 MWe sCO2 Axial Turbine

    by John D. Klaerner, J. Jeffrey Moore, Kyle Robinson, Jonathan L. Wade, Aaron McClung

    Supercritical CO2 (sCO2) power cycles designed for thermodynamic efficiencies above 50% push component designs into pressure and temperature combinations that approach the limits of American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code and ASME Piping Design Codes with Turbine inlet conditions near 250 bar and 715 °C. These design conditions which limit available materials to high nickel alloys are compounded by the high fluid densities of sCO2 at these conditions which result in very compact machinery at the 10 MWe class which are currently being developed for the DOE supercritical transformational electric power (STEP) program. Design of the STEP Turbine is complete with integrated lessons learned from a previous 1 MWth subscale demonstration of a high temperature 10 MWe Turbine designed under the DOE SunShot Program. Fabrication of the STEP Turbine is nearing completion with all housings and pressure containing components in hand. This paper provides a detailed look at design intentions and limitations for the pressurized sections of the main pressure casing and the fabrication of key turbine components. Additional discussion is provided regarding postfabrication inspection and acceptance of the casing for use after issues with casing welds were identified late in the fabrication process.


  • Open Access

    Development and Testing of a 10 MWe Supercritical CO2 Turbine in a 1 MWe Flow Loop

    by J. Jeffrey Moore, Stefan Cich, Meera Day-Towler, Jason Mortzheim

    A new high temperature turbine was developed and tested for use a sCO~2~ closed-loop recompression Brayton cycle. This turbine was developed for Concentrating Solar Power (CSP) applications (700+ºC) with funding from the US DOE Sunshot initiative and industry partners, but its application includes traditional heat sources such as natural gas, coal, and nuclear power. Traditional

  • Planning for Successful Transients and Trips in a 1 MWe-Scale High-Temperature sCO2 Test Loop

    by Timothy C. Allison, Ph.D., J. Jeffrey Moore, Douglas Hofer, Meera Day Towler, J. Michael Thorpe, Joseph Thorp

    Supercritical CO2 power cycles incorporate a unique combination of high fluid pressure, temperature, and density as well as limited component availability (e.g., high-temperature trip valves) that can result in operational challenges, particularly during off-design and transient operation. These conditions and various failure scenarios must be considered and addressed during the facility, component, and control system design phase in order to ensure machinery health and safety during operation. This paper discusses significant findings and resulting design/control requirements from a detailed failure modes and effects analysis (FMEA) that was performed for the 1 MWe-scale supercritical CO2 test loop at Southwest Research Institute, providing insight into design and control requirements for future test facilities and applications. The test loop incorporates a centrifugal pump, axial turboexpander, gas-fired primary heat exchanger, and microchannel recuperator for testing in a simple recuperated cycle configuration at pressures and temperatures up to 255 bar and 715 °C, respectively. The analysis considered off-design operation as well as high-impact failures of turbomachinery and loop components that may require fast shutdowns and blowdowns. The balance between fast shutdowns/blowdowns and the need to manage thermal stresses in the turbomachinery resulted in staged shutdown sequences and impacted the design/control strategies for major loop components and ancillary systems including the fill, vent, and seal supply systems.


  • Impact of Bearing Clearance on Measured Stiffness and Damping Coefficients and Thermal Performance of a High-Stiffness Generation 3 Foil Journal Bearing

    by Jason C. Wilkes, Jonathan Wade, Aaron Rimpel, Jeff Moore, Erik Swanson, Joseph Grieco, Jerry Brady

    High-speed foil bearings are currently used in increasingly demanding, high performance applications. The application under consideration is a 120 krpm natural gas turboexpander-compressor, which requires 38 mm (1.5 in.) foil journal bearings with high stiffness and load capacity to help enhance rotordynamic stability. This paper describes the development of the foil bearing for this application and includes measured stiffness and damping coefficients recorded on a high-speed dynamic bearing test rig. The dynamic test data were taken for several different foil bearing configurations with varying spring-element foil thicknesses, number of spring-element foils, and bearing shim thickness. All three parameters have a direct impact on bearing clearance. The influence of these different parameters on measured stiffness and damping coefficients and thermal performance of the bearings are presented and discussed.


  • An Improved Catcher Bearing Model and an Explanation of the Forward Whirl/Whip Phenomenon Observed in Active Magnetic Bearing Transient Drop Experiments

    by Jason Wilkes, Jeff Moore, David Ransom, Giuseppe Vannini

    Though many approaches have been proposed in the literature to model the reaction forces in a catcher bearing (CB), there are still phenomena observed in experimental tests that cannot be explained by existing models. The following paper presents a novel approach to model a CB system. Some of the elements in the model have been previously introduced in the literature; however, there are other elements in the proposed model that are new, providing an explanation for the forward whirling phenomena that has been observed repeatedly in the literature. The proposed CB model is implemented in a finite-element rotordynamic package, and nonlinear time-transient simulations are performed to predict published experimental results of a high-speed vertical subscale compressor; with no other forces present in the model, the agreement between simulations and experimental data is favorable. The results presented herein show that friction between the journal and axial face of the catcher bearing results in a forward cross-coupled force that pushes the rotor in the direction of rotation. This force is proportional to the coefficient of friction between the axial face of the rotor and catcher bearing and the axial thrust on the rotor. This force results in synchronous whirl when the running speed is below a combined natural frequency of the rotor-stator system and constant frequency whip when the speed is above a whip frequency.


  • Rotordynamic Force Prediction of Centrifugal Compressor Impellers Using Computational Fluid Dynamics

    by J. Jeffrey Moore, David L. Ransom, Flavia Viana

    The energy industry depends on centrifugal compressors to produce, process, reinject, and transport many different gases. Centrifugal compressors use one or more impellers to impart momentum to the flowing gas and, thereby, produce an increase in pressure through diffusion. As the operating pressure in a compressor increases, the fluid-rotor interaction at the seals and impellers become more important. Also, the new generation of megascale liquefied natural gas compressors is dependent on accurate assessment of these forces. The aerodynamic forces and cross-coupled stiffness from the impellers cannot be accurately predicted with traditional methods and must be estimated with semiempirical formulations. The result of these inaccuracies is a potential for compressor designs that can experience unexpected, dangerous, and damaging instabilities and subsynchronous vibrations. The current investigation is intended to advance the state of the art to achieve an improved, physics-based method of predicted aerodynamic destabilizing cross-coupling forces on centrifugal compressor impellers using computational fluid dynamics (CFD). CFD was employed in this study to predict the impeller-fluid interaction forces, which gives rise to the aerodynamic cross coupling. The procedure utilized in this study was developed by Moore and Palazzolo (2002, “Rotordynamic Force Prediction of Centrifugal Impeller Shroud Passages Using Computational Fluid Dynamic Techniques With Combined Primary Secondary Flow Model ,” ASME J. Eng. Gas Turbines Power, 123, pp. 910–918), which applied the method to liquid pump impellers. Their results showed good correlation to test data. Unfortunately, no such data exist for centrifugal compressors. Therefore, in order to validate the present model, comparisons will be made to predict the instability of an industrial centrifugal compressor. A parametric CFD study is then presented leading to a new analytical expression for predicting the cross-coupled stiffness for centrifugal impellers.


  • Development of a High Speed Gas Bearing Test Rig to Measure Rotordynamic Force Coefficients

    by J. Jeffrey Moore, Andrew Lerche, Timothy Allison, David L. Ransom, Daniel Lubell

    The use of gas bearings has increased over the last several decades to include microturbines, air cycle machines, and hermetically sealed compressors and turbines. Gas bearings have many advantages over traditional bearings, such as rolling element or oil lubricated fluid film bearings, including longer life, ability to use the process fluid, no contamination of the process with lubricants, accommodating high shaft speeds, and operation over a wide range of temperatures. Unlike fluid film bearings that utilize oil, gas lubricated bearings generate very little damping from the gas itself. Therefore, successful bearing designs such as foil bearings utilize damping features on the bearing to improve the damping generated. Similar to oil bearings, gas bearing designers strive to develop gas bearings with good rotordynamic stability. Gas bearings are challenging to design requiring a fully coupled thermo-elastic, hydrodynamic analysis including complex non-linear mechanisms such as Coulomb friction. There is a surprisingly low amount of rotordynamic force coefficient measurement in the literature despite the need to verify the model predictions and the stability of the bearing. This paper describes the development and testing of a 60,000 rpm gas bearing test rig and presents measured stiffness and damping coefficients for a 57 mm foil type bearing. The design of the rig overcomes many challenges in making this measurement by developing a patented, high-frequency, high-amplitude shaker system resulting in excitation over most of the subsynchronous range.

  • Rotordynamic Analysis of a Large Industrial Turbocompressor Including Finite Element Substructure Modeling

    by J. Jeffrey Moore, Giuseppe Vannini, Massimo Camatti, Paolo Bianchi

    A rotordynamic analysis of a large turbocompressor that models both the casing and supports along with the rotor-bearing system was performed. A 3D finite element model of the casing captures the intricate details of the casing and support structure. Two approaches are presented, including development of transfer functions of the casing and foundation, as well as a fully coupled rotor-casing-foundation model. The effect of bearing support compliance is captured, as well as the influence of casing modes on the rotor response. The first approach generates frequency response functions (FRFs) from the finite element case model at the bearing support locations. A high-order polynomial in numerator-denominator transfer function format is generated from a curve fit of the FRF. These transfer functions are then incorporated into the rotordynamics model. The second approach is a fully coupled rotor and casing model that is solved together. An unbalance response calculation is performed in both cases to predict the resulting rotor critical speeds and response of the casing modes. The effect of the compressor case and supports caused the second critical speed to drop to a value close to the operating speed and not compliant with the requirements of the American Petroleum Institute (API) specification 617 7th edition. A combination of rotor, journal bearing, casing, and support modifications resulted in a satisfactory and API compliant solution. The results of the fully coupled model validated the transfer function approach.


  • Centrifugal Compressor Stability Prediction Using a New Physics Based Approach

    by J. Jeffrey Moore, David L. Ransom

    The accurate prediction of centrifugal compressor stability continues to be an important area of interest in the oil and gas industry. Ensuring stability is critical to the cost-effective installation and operation of these machines in remote environments, where field stability problems are much more expensive to diagnose and correct. Current industry standards and tools for the prediction of impeller destabilizing forces are based on empirical methods that, to date, have served fairly well for systems with reasonable stability margins. However, as stability margins are decreased, use of a modeling method that is more physics based and can better represent the observed trends in machine behavior at low stability margins is required. Furthermore, the development of mega-class Liquefied Natural Gas (LNG) compressors and ultra-high pressure reinjection compressors provides further motivation to improve accuracy. In this paper, a new physics based expression for the prediction of impeller cross-coupling, previously described by Moore, et al. [1] is further investigated by analyzing several classes and scale factors of impellers ranging from 2-D designs used in reinjection to full 3-D impellers typically used in LNG. The new expression is based on both Computational Fluid Dynamics (CFD) simulation and experimental test data from a known instability. These results are then applied to two case studies of marginally stable and unstable compressors in the field that were studied by the authors’ company. For each case study, the system stability is evaluated using both the new physics based expression as well as the more traditional empirical approaches. Comparisons are made for overall stability prediction as well as sensitivity to system changes. Conclusions are made regarding the applicability and limits of this new approach.