Jeffrey L. Stein
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jeffrey L. Stein has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Tulga Ersal
University of Michigan
14 shared publications - Loucas S. Louca
Department of Mechanical and Manufacturing Engineering, University of Cyprus, Nicosia 1678, Cyprus
8 shared publications - D. Geoff Rideout
Memorial University of Newfoundland, St. John’s, NL, Canada
5 shared publications - Hosam K. Fathy
University of Michigan, Ann Arbor, MI
4 shared publications - Huei Peng
University of Michigan
3 shared publications - Kunsoo Huh
Hanyang University
3 shared publications
Latest Publications
- 1 October 2021
- Published by Wiley in Journal of Autonomous Vehicles and Systems
- Vol. 1 (4)
Real-Time Trajectory Planning for Automated Vehicle Safety and Performance in Dynamic Environments
Safe trajectory planning for high-performance automated vehicles in an environment with both static and moving obstacles is a challenging problem. Part of the challenge is developing a formulation that can be solved in real-time while including the following set of specifications: minimum time-to-goal, a dynamic vehicle model, minimum control effort, both static and moving obstacle avoidance, simultaneous optimization of speed and steering, and a short execution horizon. This paper presents a nonlinear model predictive control-based trajectory planning formulation, tailored for a large, high-speed unmanned ground vehicle, that includes the above set of specifications. The ability to solve this formulation in real-time is evaluated using NLOptControl, an open-source, direct-collocation-based optimal control problem solver in conjunction with the KNITRO nonlinear programming problem solver. The formulation is tested with various sets of specifications. A parametric study relating execution horizon and obstacle speed indicates that the moving obstacle avoidance specification is not needed for safety when the planner has a small execution horizon and the obstacles are moving slowly. However, a moving obstacle avoidance specification is needed when the obstacles are moving faster, and this specification improves the overall safety without, in most cases, increasing the solve-times. The results indicate that (i) safe trajectory planners for high-performance automated vehicles should include the entire set of specifications mentioned above, unless a static or low-speed environment permits a less comprehensive planner and (ii) the resulting formulation can be solved in real-time.
- 1 October 2021
- Published by Wiley in Journal of Autonomous Vehicles and Systems
- Vol. 1 (4)
Real-Time Trajectory Planning for Automated Vehicle Safety and Performance in Dynamic Environments
Safe trajectory planning for high-performance automated vehicles in an environment with both static and moving obstacles is a challenging problem. Part of the challenge is developing a formulation that can be solved in real-time while including the following set of specifications: minimum time-to-goal, a dynamic vehicle model, minimum control effort, both static and moving obstacle avoidance, simultaneous optimization of speed and steering, and a short execution horizon. This paper presents a nonlinear model predictive control-based trajectory planning formulation, tailored for a large, high-speed unmanned ground vehicle, that includes the above set of specifications. The ability to solve this formulation in real-time is evaluated using NLOptControl, an open-source, direct-collocation-based optimal control problem solver in conjunction with the KNITRO nonlinear programming problem solver. The formulation is tested with various sets of specifications. A parametric study relating execution horizon and obstacle speed indicates that the moving obstacle avoidance specification is not needed for safety when the planner has a small execution horizon and the obstacles are moving slowly. However, a moving obstacle avoidance specification is needed when the obstacles are moving faster, and this specification improves the overall safety without, in most cases, increasing the solve-times. The results indicate that (i) safe trajectory planners for high-performance automated vehicles should include the entire set of specifications mentioned above, unless a static or low-speed environment permits a less comprehensive planner and (ii) the resulting formulation can be solved in real-time.
- Open Access
- 6 May 2021
- Published by Morressier GmbH
Project 1.27: Mutually-Aaptive Shared Control Between Human Operators and Autonomy in Ground Vehicles
Shared control frameworks allow for transition of control authority in semi-autonomous vehicles between a human driver and autonomy to achieve a level of safety and performance that cannot be achieved by either agent alone. Shared control takes advantage of the potential codependency of the control agents, which then critically allows for adaptation. However, workload, a critical
- 6 May 2021
- Published by Morressier GmbH
Open AccessProject 1.27: Mutually-Aaptive Shared Control Between Human Operators and Autonomy in Ground Vehicles
Shared control frameworks allow for transition of control authority in semi-autonomous vehicles between a human driver and autonomy to achieve a level of safety and performance that cannot be achieved by either agent alone. Shared control takes advantage of the potential codependency of the control agents, which then critically allows for adaptation. However, workload, a critical
- Open Access
- 6 May 2021
- Published by Morressier GmbH
Project 1.27 Mutually-Adaptive Shared Control between Human Operators and Autonomy in Ground Vehicles
Project 1.27 Mutually-Adaptive Shared Control between Human Operators and Autonomy in Ground Vehicles
- 6 May 2021
- Published by Morressier GmbH
Open AccessProject 1.27 Mutually-Adaptive Shared Control between Human Operators and Autonomy in Ground Vehicles
Project 1.27 Mutually-Adaptive Shared Control between Human Operators and Autonomy in Ground Vehicles
- Open Access
NLOptControl: A modeling language for solving optimal control problems
Current direct-collocation-based optimal control software is either easy to use or fast, but not both. This is a major limitation for users that are trying to formulate complex optimal control problems (OCPs) for use in on-line applications. This paper introduces NLOptControl, an open-source modeling language that allows users to both easily formulate and quickly solve nonlinear OCPs using direct-collocation methods. To achieve these attributes, NLOptControl (1) is written in an efficient, dynamically-typed computing language called Julia, (2) extends an optimization modeling language called JuMP to provide a natural algebraic syntax for modeling nonlinear OCPs; and (3) uses reverse automatic differentiation with the acrylic-coloring method to exploit sparsity in the Hessian matrix. This work explores the novel design features of NLOptControl and compares its syntax and speed to those of PROPT. The syntax comparisons shows that NLOptControl models OCPs more concisely than PROPT. The speeds of various collocation methods within PROPT and NLOptControl are benchmarked over a range of collocation points using performance profiles; overall, NLOptControl's single, two, and four interval pseudospectral methods are roughly $14$, $26$, and $36$ times faster than PROPT's, respectively. NLOptControl is well-suited to improve existing off-line and on-line control systems and to engender new ones.Open AccessNLOptControl: A modeling language for solving optimal control problems
Current direct-collocation-based optimal control software is either easy to use or fast, but not both. This is a major limitation for users that are trying to formulate complex optimal control problems (OCPs) for use in on-line applications. This paper introduces NLOptControl, an open-source modeling language that allows users to both easily formulate and quickly solve nonlinear OCPs using direct-collocation methods. To achieve these attributes, NLOptControl (1) is written in an efficient, dynamically-typed computing language called Julia, (2) extends an optimization modeling language called JuMP to provide a natural algebraic syntax for modeling nonlinear OCPs; and (3) uses reverse automatic differentiation with the acrylic-coloring method to exploit sparsity in the Hessian matrix. This work explores the novel design features of NLOptControl and compares its syntax and speed to those of PROPT. The syntax comparisons shows that NLOptControl models OCPs more concisely than PROPT. The speeds of various collocation methods within PROPT and NLOptControl are benchmarked over a range of collocation points using performance profiles; overall, NLOptControl's single, two, and four interval pseudospectral methods are roughly $14$, $26$, and $36$ times faster than PROPT's, respectively. NLOptControl is well-suited to improve existing off-line and on-line control systems and to engender new ones. - 20 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 24 (5) , 2365-2376
A Delay Compensation Framework for Predicting Heading in Teleoperated Ground Vehicles
A delay compensation framework for teleoperated ground vehicles is developed in this paper that aims to achieve an improved prediction of vehicle heading. The framework seeks to combine the performance benefits of a model-based feedforward method with the robustness benefits of a model-free prediction scheme through a blended architecture. In particular, the feedforward heading signal from a second-order steering model is combined with the feedback heading signal from a model-free predictor. While leveraging this model-free predictor from the literature, a generic procedure is also developed for designing its gain and the predictor is further augmented with a saturation and resetting scheme to improve its transient performance. The vehicle heading prediction with the blended architecture is evaluated in two open-loop case studies and it is shown that blending the outputs of these model-based and model-free approaches can yield a more accurate prediction than either approach alone.
- 20 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 24 (5) , 2365-2376
A Delay Compensation Framework for Predicting Heading in Teleoperated Ground Vehicles
A delay compensation framework for teleoperated ground vehicles is developed in this paper that aims to achieve an improved prediction of vehicle heading. The framework seeks to combine the performance benefits of a model-based feedforward method with the robustness benefits of a model-free prediction scheme through a blended architecture. In particular, the feedforward heading signal from a second-order steering model is combined with the feedback heading signal from a model-free predictor. While leveraging this model-free predictor from the literature, a generic procedure is also developed for designing its gain and the predictor is further augmented with a saturation and resetting scheme to improve its transient performance. The vehicle heading prediction with the blended architecture is evaluated in two open-loop case studies and it is shown that blending the outputs of these model-based and model-free approaches can yield a more accurate prediction than either approach alone.
- 19 December 2018
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 141 (4)
Optimality of Norm-Optimal Iterative Learning Control Among Linear Time Invariant Iterative Learning Control Laws in Terms of Balancing Robustness and Performance
This paper presents a frequency domain analysis toward the robustness, convergence speed, and steady-state error for general linear time invariant (LTI) iterative learning control (ILC) for single-input-single-output (SISO) LTI systems and demonstrates the optimality of norm-optimal iterative learning control (NO-ILC) in terms of balancing the tradeoff between robustness, convergence speed, and steady-state error. The key part of designing LTI ILC updating laws is to choose the Q-filter and learning gain to achieve the desired robustness and performance, i.e., convergence speed and steady-state error. An analytical equation that characterizes these three terms for NO-ILC has been previously presented in the literature. For general LTI ILC updating laws, however, this relationship is still unknown. Adopting a frequency domain analysis approach, this paper characterizes this relationship for LTI ILC updating laws and, subsequently, demonstrates the optimality of NO-ILC in terms of balancing the tradeoff between robustness, convergence speed, and steady-state error.
- 19 December 2018
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 141 (4)
Optimality of Norm-Optimal Iterative Learning Control Among Linear Time Invariant Iterative Learning Control Laws in Terms of Balancing Robustness and Performance
This paper presents a frequency domain analysis toward the robustness, convergence speed, and steady-state error for general linear time invariant (LTI) iterative learning control (ILC) for single-input-single-output (SISO) LTI systems and demonstrates the optimality of norm-optimal iterative learning control (NO-ILC) in terms of balancing the tradeoff between robustness, convergence speed, and steady-state error. The key part of designing LTI ILC updating laws is to choose the Q-filter and learning gain to achieve the desired robustness and performance, i.e., convergence speed and steady-state error. An analytical equation that characterizes these three terms for NO-ILC has been previously presented in the literature. For general LTI ILC updating laws, however, this relationship is still unknown. Adopting a frequency domain analysis approach, this paper characterizes this relationship for LTI ILC updating laws and, subsequently, demonstrates the optimality of NO-ILC in terms of balancing the tradeoff between robustness, convergence speed, and steady-state error.
- 20 September 2017
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 140 (2) , 021004
A Frequency-Dependent Filter Design Approach for Norm-Optimal Iterative Learning Control and Its Fundamental Trade-Off Between Robustness, Convergence Speed, and Steady-State Error
This paper focuses on norm-optimal iterative learning control (NO-ILC) for single-input-single-output (SISO) linear time invariant (LTI) systems and presents an infinite time horizon approach for a frequency-dependent design of NO-ILC weighting filters. Because NO-ILC is a model-based learning algorithm, model uncertainty can degrade its performance; hence, ensuring robust monotonic convergence (RMC) against model uncertainty is important. This robustness, however, must be balanced against convergence speed (CS) and steady-state error (SSE). The weighting filter design approaches for NO-ILC in the literature provide limited design freedom to adjust this trade-off. Moreover, even though qualitative guidelines to adjust the trade-off exist, a quantitative characterization of the trade-off is not yet available. To address these two gaps, a frequency-dependent weighting filter design is proposed in this paper and the robustness, convergence speed, and steady-state error are analyzed in the frequency domain. An analytical expression characterizing the fundamental trade-off of NO-ILC with respect to robustness, convergence speed, and steady-state error at each frequency is presented. Compared to the state of the art, a frequency-dependent filter design gives increased freedom to adjust the trade-off between robustness, convergence speed, and steady-state error because it allows the design to meet different performance requirements at different frequencies. Simulation examples are given to confirm the analysis and demonstrate the utility of the developed filter design technique.
- 20 September 2017
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 140 (2) , 021004
A Frequency-Dependent Filter Design Approach for Norm-Optimal Iterative Learning Control and Its Fundamental Trade-Off Between Robustness, Convergence Speed, and Steady-State Error
This paper focuses on norm-optimal iterative learning control (NO-ILC) for single-input-single-output (SISO) linear time invariant (LTI) systems and presents an infinite time horizon approach for a frequency-dependent design of NO-ILC weighting filters. Because NO-ILC is a model-based learning algorithm, model uncertainty can degrade its performance; hence, ensuring robust monotonic convergence (RMC) against model uncertainty is important. This robustness, however, must be balanced against convergence speed (CS) and steady-state error (SSE). The weighting filter design approaches for NO-ILC in the literature provide limited design freedom to adjust this trade-off. Moreover, even though qualitative guidelines to adjust the trade-off exist, a quantitative characterization of the trade-off is not yet available. To address these two gaps, a frequency-dependent weighting filter design is proposed in this paper and the robustness, convergence speed, and steady-state error are analyzed in the frequency domain. An analytical expression characterizing the fundamental trade-off of NO-ILC with respect to robustness, convergence speed, and steady-state error at each frequency is presented. Compared to the state of the art, a frequency-dependent filter design gives increased freedom to adjust the trade-off between robustness, convergence speed, and steady-state error because it allows the design to meet different performance requirements at different frequencies. Simulation examples are given to confirm the analysis and demonstrate the utility of the developed filter design technique.
- Open Access
- 5 June 2017
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 139 (9)
Battery State of Health Monitoring by Estimation of Side Reaction Current Density Via Retrospective-Cost Subsystem Identification
This paper introduces a new method to monitor battery state of health (SOH). In particular, the side reaction current density is estimated as a direct SOH indicator for the first time and its estimation is formulated as an inaccessible subsystem identification problem, where the battery health subsystem is treated as an inaccessible subsystem with the side reaction current density as the output. Inaccessibility in this context refers to the fact that the inputs and outputs of the subsystem are not measurable in situ. This subsystem is identified using retrospective-cost subsystem identification (RCSI) algorithm, and the output of the identified battery health subsystem provides an estimate for the side reaction current density. Using an example parameter set for a LiFePO4 battery, simulations are performed to obtain estimates under various current profiles. These simulations show promising results in identifying the battery health subsystem and estimating the side reaction current density with RCSI under ideal conditions. Robustness of the algorithm under nonideal conditions is analyzed. Estimation of the side reaction current density using RCSI is shown to be sensitive to nonideal conditions that cause errors in the measurement or estimation of the battery voltage. A method for quantitatively assessing the impact of nonideal conditions on the side reaction current estimation accuracy is provided. The proposed estimation technique, including the method for estimating the side reaction current density using RCSI and the framework analyzing its robustness, can also be applied to other parameter sets and other battery chemistries to monitor the SOH change resulting from any electrochemical-based degradation mechanism that consumes cyclable Li-ions.
- 5 June 2017
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 139 (9)
Open AccessBattery State of Health Monitoring by Estimation of Side Reaction Current Density Via Retrospective-Cost Subsystem Identification
This paper introduces a new method to monitor battery state of health (SOH). In particular, the side reaction current density is estimated as a direct SOH indicator for the first time and its estimation is formulated as an inaccessible subsystem identification problem, where the battery health subsystem is treated as an inaccessible subsystem with the side reaction current density as the output. Inaccessibility in this context refers to the fact that the inputs and outputs of the subsystem are not measurable in situ. This subsystem is identified using retrospective-cost subsystem identification (RCSI) algorithm, and the output of the identified battery health subsystem provides an estimate for the side reaction current density. Using an example parameter set for a LiFePO4 battery, simulations are performed to obtain estimates under various current profiles. These simulations show promising results in identifying the battery health subsystem and estimating the side reaction current density with RCSI under ideal conditions. Robustness of the algorithm under nonideal conditions is analyzed. Estimation of the side reaction current density using RCSI is shown to be sensitive to nonideal conditions that cause errors in the measurement or estimation of the battery voltage. A method for quantitatively assessing the impact of nonideal conditions on the side reaction current estimation accuracy is provided. The proposed estimation technique, including the method for estimating the side reaction current density using RCSI and the framework analyzing its robustness, can also be applied to other parameter sets and other battery chemistries to monitor the SOH change resulting from any electrochemical-based degradation mechanism that consumes cyclable Li-ions.
- 1 January 2015
- Published by Elsevier in IFAC-PapersOnLine
- Vol. 48 (12) , 434-439
Performance Analysis of a Model-Free Predictor for Delay Compensation in Networked Systems∗∗This work was supported by the Automotive Research Center (ARC) in accordance with Cooperative Agreement W56HZV–142–0001 U.S. Army Tank Automotive Research, Development and Engineering Center (TARDEC) Warren, MI. UNCLASSIFIED: Distribution Statement A. Approved for public release. #26203
- 1 January 2015
- Published by Elsevier in IFAC-PapersOnLine
- Vol. 48 (12) , 434-439
Performance Analysis of a Model-Free Predictor for Delay Compensation in Networked Systems∗∗This work was supported by the Automotive Research Center (ARC) in accordance with Cooperative Agreement W56HZV–142–0001 U.S. Army Tank Automotive Research, Development and Engineering Center (TARDEC) Warren, MI. UNCLASSIFIED: Distribution Statement A. Approved for public release. #26203
- 8 August 2014
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 136 (6) , 061012
An Iterative Learning Control Approach to Improving Fidelity in Internet-Distributed Hardware-in-the-Loop Simulation
One of the main challenges of cosimulating hardware-in-the-loop (HIL) systems in real-time over the Internet is the fidelity of the simulation. The dynamics of the Internet may significantly distort the dynamics of the network-integrated system. This paper presents the development and experimental validation of an iterative learning control (ILC) based approach to improve fidelity of such networked system integration. Toward this end, a new metric for characterizing coupling fidelity is proposed, which, unlike some existing metrics, enables the formulation of the problem of improving system fidelity without requiring any knowledge about the reference dynamics (i.e., dynamics that would be observed, if the system was physically connected). Next, using this metric, the problem of improving fidelity is formulated as an ILC problem. The proposed approach is illustrated on an experimental setup simulating a hybrid electric powertrain distributed across three different sites with a real engine and battery in the loop. The conclusion is that the proposed approach holds significant potential for achieving high fidelity in Internet-distributed HIL (ID-HIL) simulation setups.
- 8 August 2014
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 136 (6) , 061012
An Iterative Learning Control Approach to Improving Fidelity in Internet-Distributed Hardware-in-the-Loop Simulation
One of the main challenges of cosimulating hardware-in-the-loop (HIL) systems in real-time over the Internet is the fidelity of the simulation. The dynamics of the Internet may significantly distort the dynamics of the network-integrated system. This paper presents the development and experimental validation of an iterative learning control (ILC) based approach to improve fidelity of such networked system integration. Toward this end, a new metric for characterizing coupling fidelity is proposed, which, unlike some existing metrics, enables the formulation of the problem of improving system fidelity without requiring any knowledge about the reference dynamics (i.e., dynamics that would be observed, if the system was physically connected). Next, using this metric, the problem of improving fidelity is formulated as an ILC problem. The proposed approach is illustrated on an experimental setup simulating a hybrid electric powertrain distributed across three different sites with a real engine and battery in the loop. The conclusion is that the proposed approach holds significant potential for achieving high fidelity in Internet-distributed HIL (ID-HIL) simulation setups.