Kan-Sen Chou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kan-Sen Chou has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
I-Hsien Lai
Department of Chemical Engineering, National Tsing Hua University, Hsinchu, Taiwan
2 shared publicationsYu-Chieh Lu
Department of Chemical Engineering, National Tsing Hua University
2 shared publicationsChen-Yu Kao
Department of Chemical Engineering, National Tsing Hua University, Hsinchu, Taiwan 30013
1 shared publicationChia-Hsuan Lee
Department of Chemical Engineering, National Tsing Hua University, Hsinchu 30013, Taiwan
1 shared publicationChieh-Tsung Lo
1 shared publicationJyh-Ching Tsai
1 shared publication
Latest Publications
- 6 October 2015
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 93 (6) , 468-480
Effect of titania addition on adhesion of silver colloids to glass substrate
The purpose of this study was to investigate the effects of titania addition on adhesion strength of silver colloids to glass substrate. Our results indicated that when the pH was adjusted to 10, the mixed slurry of titania and silver colloids was stable with no sign of settling at approximately 4 hr. After film deposition by doctor blade method and subsequent sintering treatment, the adhesion strength between silver film and glass substrate was measured by both ASTM D3359 and D4541 standards. The results showed positive correlation of adhesion strength to both the titania concentration and sintering temperature. The adhesion strength reached 7.0 MPa when we added 8 wt% titania (based on silver) and sintered the film at 320°C for 20 min. X-ray photoelectron spectroscopy data revealed that interdiffusion of Ti into both glass substrate and silver colloid might be responsible for adhesion enhancement. On the other hand, the electrical resistivity of films increased with titania addition. This fact implied that we need to compromise between these two properties when titania addition was used to improve adhesion between silver colloid and glass substrate. An empirical model was subsequently proposed to simulate the compromise between adhesion strength and electrical resistivity.
- 6 October 2015
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 93 (6) , 468-480
Effect of titania addition on adhesion of silver colloids to glass substrate
The purpose of this study was to investigate the effects of titania addition on adhesion strength of silver colloids to glass substrate. Our results indicated that when the pH was adjusted to 10, the mixed slurry of titania and silver colloids was stable with no sign of settling at approximately 4 hr. After film deposition by doctor blade method and subsequent sintering treatment, the adhesion strength between silver film and glass substrate was measured by both ASTM D3359 and D4541 standards. The results showed positive correlation of adhesion strength to both the titania concentration and sintering temperature. The adhesion strength reached 7.0 MPa when we added 8 wt% titania (based on silver) and sintered the film at 320°C for 20 min. X-ray photoelectron spectroscopy data revealed that interdiffusion of Ti into both glass substrate and silver colloid might be responsible for adhesion enhancement. On the other hand, the electrical resistivity of films increased with titania addition. This fact implied that we need to compromise between these two properties when titania addition was used to improve adhesion between silver colloid and glass substrate. An empirical model was subsequently proposed to simulate the compromise between adhesion strength and electrical resistivity.
- 21 May 2015
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 92 (6) , 429-439
Surface Roughness on Adhesion of Silver Colloids to a Polyimide Substrate
The adhesion of silver colloids to a polyimide (PI) substrate was investigated in this study. This issue would be of concern when one tried to print electronic circuits on a flexible PI substrate. To enhance the adhesion between them, the PI surface was first roughened by using the sandblasting technique, and varying degrees of roughness were achieved using various sizes of alumina particles and various air pressures for sandblasting. The adhesion strength of silver colloids to the PI substrate after sintering was then measured according to both ASTM D4541 and ASTM 3359 standards. The results indicated that adhesion strength increased proportionally with surface roughness; however, this enhancement effect was lessened when the roughness was above 880 nm. Sintering temperature was also beneficial in increasing adhesion to the substrate; however, the electrical resistance of the silver colloids after sintering also increased with the degree of roughness. This implied that the packing of silver colloids was also affected by surface roughness. Consequently, values of surface roughness were optimal when adhesion strength and electrical resistivity were balanced.
- 21 May 2015
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 92 (6) , 429-439
Surface Roughness on Adhesion of Silver Colloids to a Polyimide Substrate
The adhesion of silver colloids to a polyimide (PI) substrate was investigated in this study. This issue would be of concern when one tried to print electronic circuits on a flexible PI substrate. To enhance the adhesion between them, the PI surface was first roughened by using the sandblasting technique, and varying degrees of roughness were achieved using various sizes of alumina particles and various air pressures for sandblasting. The adhesion strength of silver colloids to the PI substrate after sintering was then measured according to both ASTM D4541 and ASTM 3359 standards. The results indicated that adhesion strength increased proportionally with surface roughness; however, this enhancement effect was lessened when the roughness was above 880 nm. Sintering temperature was also beneficial in increasing adhesion to the substrate; however, the electrical resistance of the silver colloids after sintering also increased with the degree of roughness. This implied that the packing of silver colloids was also affected by surface roughness. Consequently, values of surface roughness were optimal when adhesion strength and electrical resistivity were balanced.
- Open Access
- 7 August 2014
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2014, 1-5
Fabrication of Silver Interdigitated Electrode by a Stamp Method
A stamp method was developed in this study to fabricate interdigitated electrodes (IDEs) on glass substrate from a 37.5 wt% silver ink. This method is simple and fast. A small amount of silver ink was first dripped into an IDE-patterned sponge of a stamp and then one could stamp out the desired IDE pattern made of nanosized silver colloids on a glass substrate, which was subsequently sintered at 280°C for 10 minutes to obtain the final silver IDE. Our brief study showed that when a large stamping force was used, more ink would be stamped out in the beginning and it decreased after each usage. However, if the force was too small, there would not be sufficient ink for a complete IDE. There existed therefore an optimal force to fabricate IDEs with minimal changes from sample to sample. The average dimension of an IDE when the applied force was 102 gm was roughly 403 ± 20 µm in width and 1154 ± 153 nm in height, and the average final electrical resistivity was about Ω-cm.- 7 August 2014
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2014, 1-5
Open AccessFabrication of Silver Interdigitated Electrode by a Stamp Method
A stamp method was developed in this study to fabricate interdigitated electrodes (IDEs) on glass substrate from a 37.5 wt% silver ink. This method is simple and fast. A small amount of silver ink was first dripped into an IDE-patterned sponge of a stamp and then one could stamp out the desired IDE pattern made of nanosized silver colloids on a glass substrate, which was subsequently sintered at 280°C for 10 minutes to obtain the final silver IDE. Our brief study showed that when a large stamping force was used, more ink would be stamped out in the beginning and it decreased after each usage. However, if the force was too small, there would not be sufficient ink for a complete IDE. There existed therefore an optimal force to fabricate IDEs with minimal changes from sample to sample. The average dimension of an IDE when the applied force was 102 gm was roughly 403 ± 20 µm in width and 1154 ± 153 nm in height, and the average final electrical resistivity was about Ω-cm. - 26 March 2012
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 51 (13) , 4905-4910
Studies on the Continuous Precipitation of Silver Nanoparticles
- 26 March 2012
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 51 (13) , 4905-4910
Studies on the Continuous Precipitation of Silver Nanoparticles
- 12 November 2011
- Published by Oxford University Press (OUP) in Chemistry Letters
- Vol. 40 (12) , 1352-1353
Diameter Control of Silver Nanowires by Chloride Ions and Its Application as Transparent Conductive Coating
- 12 November 2011
- Published by Oxford University Press (OUP) in Chemistry Letters
- Vol. 40 (12) , 1352-1353
Diameter Control of Silver Nanowires by Chloride Ions and Its Application as Transparent Conductive Coating
- 15 July 2009
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 116 (1) , 1-5
Process window for the synthesis of Ag wires through polyol process
- 15 July 2009
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 116 (1) , 1-5
Process window for the synthesis of Ag wires through polyol process
- 1 March 2009
- Published by Elsevier in Colloids and Surfaces A: Physicochemical and Engineering Aspects
- Vol. 336 (1-3) , 23-28
Facile methods to synthesize nanaosized iron oxide colloidal dispersion and its characterization
- 1 March 2009
- Published by Elsevier in Colloids and Surfaces A: Physicochemical and Engineering Aspects
- Vol. 336 (1-3) , 23-28
Facile methods to synthesize nanaosized iron oxide colloidal dispersion and its characterization
- 1 August 2007
- Published by Elsevier in Electrochemistry Communications
- Vol. 9 (8) , 1907-1912
Microstructure changes to iron nanoparticles during discharge/charge cycles
- 1 August 2007
- Published by Elsevier in Electrochemistry Communications
- Vol. 9 (8) , 1907-1912
Microstructure changes to iron nanoparticles during discharge/charge cycles
- 1 January 2007
- Published by The Electrochemical Society in Electrochemical and Solid-State Letters
- Vol. 10 (3) , D32-D34
Electroless Copper Plating onto Printed Lines of Nanosized Silver Seeds
It was demonstrated that continuous copper films could be grown onto printed lines of nanosized silver colloids. These silver colloids, with an average size of , were printed on alumina substrates by either an ink-jet printer or a felt-tip pen and then served as a seed layer for subsequent electroless copper plating. A complete copper film could be obtained in less than when the surface density of silver particles was greater than and an appropriate plating solution to produce a mean copper growth rate of . After of growth and a resulting film thickness of , the measured electric resistivity of the lines was about , being very close to bulk copper. In addition, the measured peel adhesion strength between the deposited copper film and the substrate was larger than .
- 1 January 2007
- Published by The Electrochemical Society in Electrochemical and Solid-State Letters
- Vol. 10 (3) , D32-D34
Electroless Copper Plating onto Printed Lines of Nanosized Silver Seeds
It was demonstrated that continuous copper films could be grown onto printed lines of nanosized silver colloids. These silver colloids, with an average size of , were printed on alumina substrates by either an ink-jet printer or a felt-tip pen and then served as a seed layer for subsequent electroless copper plating. A complete copper film could be obtained in less than when the surface density of silver particles was greater than and an appropriate plating solution to produce a mean copper growth rate of . After of growth and a resulting film thickness of , the measured electric resistivity of the lines was about , being very close to bulk copper. In addition, the measured peel adhesion strength between the deposited copper film and the substrate was larger than .
- 22 April 2005
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 97 (1) , 128-135
Effect of mixing process on electromagnetic interference shielding effectiveness of nickel/acrylonitrile–butadiene–styrene composites
This article reports the effect of the mixing process on the electromagnetic interference (EMI) shielding effectiveness of nickel/acrylonitrile–butadiene–styrene (ABS) composites. Nickel in either powder or filament form was used as the filler material. It was mixed with ABS by two mixing processes: one was the Brabender‐mixing method, in which nickel was mixed in the polymer melt by a strong shear at high temperatures, and the other was a simple dry mixing method performed in a centrifugal ball mill. Our results showed that the dry‐mixing method could produce EMI shielding effectiveness of 36 dB at the 3 vol % nickel filaments level. In contrast, we need 20 vol % nickel powder to exhibit some shielding effectiveness for the Brabender method. After the nondestructive X‐ray examination and four‐point probe resistivity measurements, we concluded that better EMI shielding effectiveness could be achieved when the mixing method provided a state of uniformity on the macroscale, but not on the microscale. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 128–135, 2005
- 22 April 2005
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 97 (1) , 128-135
Effect of mixing process on electromagnetic interference shielding effectiveness of nickel/acrylonitrile–butadiene–styrene composites
This article reports the effect of the mixing process on the electromagnetic interference (EMI) shielding effectiveness of nickel/acrylonitrile–butadiene–styrene (ABS) composites. Nickel in either powder or filament form was used as the filler material. It was mixed with ABS by two mixing processes: one was the Brabender‐mixing method, in which nickel was mixed in the polymer melt by a strong shear at high temperatures, and the other was a simple dry mixing method performed in a centrifugal ball mill. Our results showed that the dry‐mixing method could produce EMI shielding effectiveness of 36 dB at the 3 vol % nickel filaments level. In contrast, we need 20 vol % nickel powder to exhibit some shielding effectiveness for the Brabender method. After the nondestructive X‐ray examination and four‐point probe resistivity measurements, we concluded that better EMI shielding effectiveness could be achieved when the mixing method provided a state of uniformity on the macroscale, but not on the microscale. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 128–135, 2005