Onur Sayman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Onur Sayman has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Mustafa Ozen
Harran University
3 shared publications - Adnan Özel
Atatürk University
2 shared publications - Ahmet Okur
Dokuz Eylül University, Izmir Vocational School of Higher Education, 35150, Buca, Izmir, Turkey
1 shared publication Ahmet Pasinli
Ege Technical Training High School , Ege University , Bornova, Izmir , Turkey
1 shared publication- Aytac Goren
Dokuz Eylul University
1 shared publication Behiye Korkmaz
Engineering Faculty, Department of Mechanical Engineering, Uludag University, Gorukle, Bursa, Turkey
1 shared publication
Latest Publications
- 19 March 2013
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 27 (21) , 2304-2314
Nonlinear stress analysis in adhesively bonded single-lap joint
In this investigation, an analytical elastic–plastic solution was proposed for a single-lap joint. A ductile adhesive joint material was used as the bond material. FM-73 was utilized in the study. The influence of the bending moment was neglected in the solution. The solution was modified for shear stresses. The analytical solution was compared with the FEM solution. An ANSYS 10.0 solution was employed in the numerical solution. Both solutions were compared with each other. These two solutions produced close agreements.
- 19 March 2013
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 27 (21) , 2304-2314
Nonlinear stress analysis in adhesively bonded single-lap joint
In this investigation, an analytical elastic–plastic solution was proposed for a single-lap joint. A ductile adhesive joint material was used as the bond material. FM-73 was utilized in the study. The influence of the bending moment was neglected in the solution. The solution was modified for shear stresses. The analytical solution was compared with the FEM solution. An ANSYS 10.0 solution was employed in the numerical solution. Both solutions were compared with each other. These two solutions produced close agreements.
- 1 January 2013
- Vol. 15 (3) , 19-27
Modeling and stress analyses of a normal foot-ankle and a prosthetic foot-ankle complex.
Total ankle replacement (TAR) is a relatively new concept and is becoming more popular for treatment of ankle arthritis and fractures. Because of the high costs and difficulties of experimental studies, the developments of TAR prostheses are progressing very slowly. For this reason, the medical imaging techniques such as CT, and MR have become more and more useful. The finite element method (FEM) is a widely used technique to estimate the mechanical behaviors of materials and structures in engineering applications. FEM has also been increasingly applied to biomechanical analyses of human bones, tissues and organs, thanks to the development of both the computing capabilities and the medical imaging techniques. 3-D finite element models of the human foot and ankle from reconstruction of MR and CT images have been investigated by some authors. In this study, data of geometries (used in modeling) of a normal and a prosthetic foot and ankle were obtained from a 3D reconstruction of CT images. The segmentation software, MIMICS was used to generate the 3D images of the bony structures, soft tissues and components of prosthesis of normal and prosthetic ankle-foot complex. Except the spaces between the adjacent surface of the phalanges fused, metatarsals, cuneiforms, cuboid, navicular, talus and calcaneus bones, soft tissues and components of prosthesis were independently developed to form foot and ankle complex. SOLIDWORKS program was used to form the boundary surfaces of all model components and then the solid models were obtained from these boundary surfaces. Finite element analyses software, ABAQUS was used to perform the numerical stress analyses of these models for balanced standing position. Plantar pressure and von Mises stress distributions of the normal and prosthetic ankles were compared with each other. There was a peak pressure increase at the 4th metatarsal, first metatarsal and talus bones and a decrease at the intermediate cuneiform and calcaneus bones, in prosthetic ankle-foot complex compared to normal one. The predicted plantar pressures and von Misses stress distributions for a normal foot were consistent with other FE models given in the literature. The present study is aimed to open new approaches for the development of ankle prosthesis.
- 1 January 2013
- Vol. 15 (3) , 19-27
Modeling and stress analyses of a normal foot-ankle and a prosthetic foot-ankle complex.
Total ankle replacement (TAR) is a relatively new concept and is becoming more popular for treatment of ankle arthritis and fractures. Because of the high costs and difficulties of experimental studies, the developments of TAR prostheses are progressing very slowly. For this reason, the medical imaging techniques such as CT, and MR have become more and more useful. The finite element method (FEM) is a widely used technique to estimate the mechanical behaviors of materials and structures in engineering applications. FEM has also been increasingly applied to biomechanical analyses of human bones, tissues and organs, thanks to the development of both the computing capabilities and the medical imaging techniques. 3-D finite element models of the human foot and ankle from reconstruction of MR and CT images have been investigated by some authors. In this study, data of geometries (used in modeling) of a normal and a prosthetic foot and ankle were obtained from a 3D reconstruction of CT images. The segmentation software, MIMICS was used to generate the 3D images of the bony structures, soft tissues and components of prosthesis of normal and prosthetic ankle-foot complex. Except the spaces between the adjacent surface of the phalanges fused, metatarsals, cuneiforms, cuboid, navicular, talus and calcaneus bones, soft tissues and components of prosthesis were independently developed to form foot and ankle complex. SOLIDWORKS program was used to form the boundary surfaces of all model components and then the solid models were obtained from these boundary surfaces. Finite element analyses software, ABAQUS was used to perform the numerical stress analyses of these models for balanced standing position. Plantar pressure and von Mises stress distributions of the normal and prosthetic ankles were compared with each other. There was a peak pressure increase at the 4th metatarsal, first metatarsal and talus bones and a decrease at the intermediate cuneiform and calcaneus bones, in prosthetic ankle-foot complex compared to normal one. The predicted plantar pressures and von Misses stress distributions for a normal foot were consistent with other FE models given in the literature. The present study is aimed to open new approaches for the development of ankle prosthesis.
- Open Access
- 17 December 2012
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 20 (2) , 163-168
A non-linear elastic-plastic stress analysis in a ductile double-lap joint
In this study, an elastic-plastic stress analysis was proposed in order to obtain shear stress distribution in a double-lap joint, analytically. The solution was carried out using incremental theory. The obtained shear stress was then used for determining the peel stress in the adhesive. The elastic peel stress distribution in the adhesive was determined using Newton-Raphson method. In this study, FM73 (Cytec Industries Inc., New Jersey, USA) ductile adhesive was selected as it represents plastic hardening. The analytical results were compared with the finite element solution. For that, ANSYS 10 Software (Figes Engineering A.S., Turkey) was used so as to compare with the analytical results. A good agreement was obtained between the two methods.
- 17 December 2012
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 20 (2) , 163-168
Open AccessA non-linear elastic-plastic stress analysis in a ductile double-lap joint
In this study, an elastic-plastic stress analysis was proposed in order to obtain shear stress distribution in a double-lap joint, analytically. The solution was carried out using incremental theory. The obtained shear stress was then used for determining the peel stress in the adhesive. The elastic peel stress distribution in the adhesive was determined using Newton-Raphson method. In this study, FM73 (Cytec Industries Inc., New Jersey, USA) ductile adhesive was selected as it represents plastic hardening. The analytical results were compared with the finite element solution. For that, ANSYS 10 Software (Figes Engineering A.S., Turkey) was used so as to compare with the analytical results. A good agreement was obtained between the two methods.
- Open Access
- 1 December 2011
- Published by MDPI AG in Mathematical and Computational Applications
- Vol. 16 (3) , 598-604
Thermal Stress Analysis in ZrO2 Insulation Coatings on Cr-Ni Substrates during Cooling Process
In this study, thermal stresses analysis of ZrO2 insulation coatings on Cr-Ni substrate during the cooling process was investigated. A transient thermal analysis was performed using finite element method (FEM) via ANSYS software. The temperature versus the time curve obtained from FEM solution was controlled with the temperaturetime diagram measured by a thermocouple. The results obtained from the numerical calculations were improved by the experimental measurement. Additionally, residual stresses were calculated by FEM solutions and they were compared in different points. The compressive and tensile stresses occurred in ZrO2 coating and Cr-Ni substrate owing to the different thermal expansion coefficients in each material, respectively.
- 1 December 2011
- Published by MDPI AG in Mathematical and Computational Applications
- Vol. 16 (3) , 598-604
Open AccessThermal Stress Analysis in ZrO2 Insulation Coatings on Cr-Ni Substrates during Cooling Process
In this study, thermal stresses analysis of ZrO2 insulation coatings on Cr-Ni substrate during the cooling process was investigated. A transient thermal analysis was performed using finite element method (FEM) via ANSYS software. The temperature versus the time curve obtained from FEM solution was controlled with the temperaturetime diagram measured by a thermocouple. The results obtained from the numerical calculations were improved by the experimental measurement. Additionally, residual stresses were calculated by FEM solutions and they were compared in different points. The compressive and tensile stresses occurred in ZrO2 coating and Cr-Ni substrate owing to the different thermal expansion coefficients in each material, respectively.
- Open Access
- 1 December 2011
- Published by MDPI AG in Mathematical and Computational Applications
- Vol. 16 (4) , 849-857
Elastic-Plastic and Residual Stresses in Clamped Thermoplastic Composite Laminates Loaded Transversely
In this study, an elastic-plastic stress analysis was carried out in woven steel fibers- thermoplastic clamped composite laminates. The stacking sequences were chosen as [0/0]2, [15/-15]2, [30/-30]2 and [45/-45]2 for woven steel fibers – thermoplastic composites plates. The layers were chosen for symmetric and antisymmetric cases. The finite element solution was performed by using the ANSYS software. Solid 186 element was utilized in the solution. Normal stress components at the clamped edges were found to be higher than that at the mid point of the laminated plates. Normal stresses are tensile at the mid point of the clamped edges and compressive at the mid point of the laminated plates. Then, the residual stress components were calculated in the critical points of the composite laminates.
- 1 December 2011
- Published by MDPI AG in Mathematical and Computational Applications
- Vol. 16 (4) , 849-857
Open AccessElastic-Plastic and Residual Stresses in Clamped Thermoplastic Composite Laminates Loaded Transversely
In this study, an elastic-plastic stress analysis was carried out in woven steel fibers- thermoplastic clamped composite laminates. The stacking sequences were chosen as [0/0]2, [15/-15]2, [30/-30]2 and [45/-45]2 for woven steel fibers – thermoplastic composites plates. The layers were chosen for symmetric and antisymmetric cases. The finite element solution was performed by using the ANSYS software. Solid 186 element was utilized in the solution. Normal stress components at the clamped edges were found to be higher than that at the mid point of the laminated plates. Normal stresses are tensile at the mid point of the clamped edges and compressive at the mid point of the laminated plates. Then, the residual stress components were calculated in the critical points of the composite laminates.
- 3 February 2009
- Published by Wiley in Polymer Composites
- Vol. 31 (1) , 173-178
Experimental failure analysis of bolted joints in moisture‐ and temperature‐induced composite laminates under preload
In this study, an experimental investigation was carried out in a bolted glass fiber‐reinforced laminate under preload moments. The stacking sequence at the composite laminate was chosen as [90°/0°/45°/−30°]s. The preload moments were selected as 2, 4, and 6 Nm, in order to compare the influence of preload moments on failure modes and strengths. Some specimens were subjected to hot pure water at 70°C for 7 days. The bearing strength in this case was measured again under the same preload moments of 2, 4, and 6 Nm. It is found that the bearing strength of the specimen waited in hot water was 5.4% smaller than that of the specimen in dry condition. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers
- 3 February 2009
- Published by Wiley in Polymer Composites
- Vol. 31 (1) , 173-178
Experimental failure analysis of bolted joints in moisture‐ and temperature‐induced composite laminates under preload
In this study, an experimental investigation was carried out in a bolted glass fiber‐reinforced laminate under preload moments. The stacking sequence at the composite laminate was chosen as [90°/0°/45°/−30°]s. The preload moments were selected as 2, 4, and 6 Nm, in order to compare the influence of preload moments on failure modes and strengths. Some specimens were subjected to hot pure water at 70°C for 7 days. The bearing strength in this case was measured again under the same preload moments of 2, 4, and 6 Nm. It is found that the bearing strength of the specimen waited in hot water was 5.4% smaller than that of the specimen in dry condition. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers
- 31 October 2007
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 27 (1) , 69-81
Failure Analysis of Bolted Aluminum Sandwich Composite Plates under Compressive Preload
The aim of this study is to examine the failure load and failure mode in an aluminum— glass-epoxy sandwich composite plate fastened mechanically by a bolt and washers on a circular hole under a preload exerted by a moment. Parametric studies were performed by experiments to find out the effects of joint geometry and preload moment on the failure strength and failure mode. The preload moments chosen (M) were 0, 3 and 6 Nm while the end distance to hole diameter (E/D) and width to diameter (W/D) ratios were chosen as 1—5 and 2—5, respectively. It is concluded from these experiments that the failure load increases with the increase of M, E/D and W/D. When M, E/D and W/D ratios reach 3—6, 2—5 and 5 Nm, full bearing strengths occur, respectively. When E/D = 1 for all the widths and preload moments, the shear-out failure mode is observed. The mixed modes, especially bearing and net-tension, are observed for E/D and W/D equal to 2—5 and 3—4, respectively. The preload moments increase the failure strengths of the composite laminate.
- 31 October 2007
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 27 (1) , 69-81
Failure Analysis of Bolted Aluminum Sandwich Composite Plates under Compressive Preload
The aim of this study is to examine the failure load and failure mode in an aluminum— glass-epoxy sandwich composite plate fastened mechanically by a bolt and washers on a circular hole under a preload exerted by a moment. Parametric studies were performed by experiments to find out the effects of joint geometry and preload moment on the failure strength and failure mode. The preload moments chosen (M) were 0, 3 and 6 Nm while the end distance to hole diameter (E/D) and width to diameter (W/D) ratios were chosen as 1—5 and 2—5, respectively. It is concluded from these experiments that the failure load increases with the increase of M, E/D and W/D. When M, E/D and W/D ratios reach 3—6, 2—5 and 5 Nm, full bearing strengths occur, respectively. When E/D = 1 for all the widths and preload moments, the shear-out failure mode is observed. The mixed modes, especially bearing and net-tension, are observed for E/D and W/D equal to 2—5 and 3—4, respectively. The preload moments increase the failure strengths of the composite laminate.
- 1 November 2006
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 25 (16) , 1709-1722
Thermal Stresses in a Thermoplastic Composite Disc under a Steady State Temperature Distribution
In the present study, an elastic-plastic stress analysis is carried out in a thermoplastic composite disc reinforced by steel fibers curvilinearly under a steady state temperature distribution. Elastic, elastic-plastic, and residual stresses are calculated in the solution. The largest tangential stress and the highest residual stress components are found around the inner portion of the disc. The solution is also performed by the finite element solution. Both solutions are observed to be in good agreement.
- 1 November 2006
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 25 (16) , 1709-1722
Thermal Stresses in a Thermoplastic Composite Disc under a Steady State Temperature Distribution
In the present study, an elastic-plastic stress analysis is carried out in a thermoplastic composite disc reinforced by steel fibers curvilinearly under a steady state temperature distribution. Elastic, elastic-plastic, and residual stresses are calculated in the solution. The largest tangential stress and the highest residual stress components are found around the inner portion of the disc. The solution is also performed by the finite element solution. Both solutions are observed to be in good agreement.
- 28 February 2002
- Published by Elsevier in Composites Science and Technology
- Vol. 62 (2) , 265-273
An elastic–plastic stress analysis of simply supported metal-matrix composite beams under a transverse uniformly distributed load
- 28 February 2002
- Published by Elsevier in Composites Science and Technology
- Vol. 62 (2) , 265-273
An elastic–plastic stress analysis of simply supported metal-matrix composite beams under a transverse uniformly distributed load
- 1 November 2001
- Published by Elsevier in Composites Science and Technology
- Vol. 61 (14) , 2129-2137
Elastic–plastic thermal stress analysis of aluminum-martix composite beams under a parabolically temperature distribution
- 1 November 2001
- Published by Elsevier in Composites Science and Technology
- Vol. 61 (14) , 2129-2137
Elastic–plastic thermal stress analysis of aluminum-martix composite beams under a parabolically temperature distribution