Kazufumi Nomura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kazufumi Nomura has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Satoru Asai
Graduate School of Engineering, Osaka University, Osaka, Japan
5 shared publications- Satoru Asai
DAIHEN Welding and Joining Research Alliance Laboratories, Joining and Welding Research Institute, The University of Osaka, Osaka 567-0047, Japan
4 shared publications Yoshinori Hirata
Osaka University
4 shared publicationsSatoshi Otaki
Graduate School of Engineering, Osaka University, Osaka, Japan
3 shared publicationsTakashi Kishi
Osaka University
3 shared publicationsTaketo Matsuida
Graduate School of Engineering, Osaka University, Osaka, Japan
3 shared publications
Latest Publications
- Open Access
- 9 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (2) , 688
Study on Non-Contact Defect Detection Using the Laser Ultrasonic Method for Friction Stir-Welded Cu–Al Dissimilar Material Joints
Ensuring friction stir welding (FSW) joint quality typically relies on ultrasonic testing (UT) and radiographic testing (RT), but achieving complete coverage is challenging, and echo-based defect discrimination becomes difficult in dissimilar joints. Laser ultrasonics is a promising non-contact technique that remotely assesses weld quality and provides high spatial resolution at the generation and detection points. This study establishes a laser-ultrasonic method for defect detection in dissimilar Cu–Al FSW joints. Slit-like artificial defects (0.1–2.5 mm deep in 5 mm thick plates) were introduced at the Al-side interface of specimens fabricated with an Al-offset tool. Experiments and numerical simulations were used to evaluate wave modes and irradiation configurations, focusing on intensity-attenuation ratios of specific wave types, including longitudinal and Rayleigh waves. On the non-slit surface, attenuation of reflected longitudinal waves enabled detection of defects ≥0.5 mm deep. On the slit surface, Rayleigh-wave attenuation allowed identification of defects as shallow as 0.1 mm, although slit-side irradiation may be less practical during joining. These results demonstrate that defect identification in dissimilar materials can be achieved by evaluating wave-intensity attenuation rather than relying solely on the presence of reflected echoes, suggesting potential for implementing laser ultrasonics in in-process monitoring of FSW joints.
- 9 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (2) , 688
Open AccessStudy on Non-Contact Defect Detection Using the Laser Ultrasonic Method for Friction Stir-Welded Cu–Al Dissimilar Material Joints
Ensuring friction stir welding (FSW) joint quality typically relies on ultrasonic testing (UT) and radiographic testing (RT), but achieving complete coverage is challenging, and echo-based defect discrimination becomes difficult in dissimilar joints. Laser ultrasonics is a promising non-contact technique that remotely assesses weld quality and provides high spatial resolution at the generation and detection points. This study establishes a laser-ultrasonic method for defect detection in dissimilar Cu–Al FSW joints. Slit-like artificial defects (0.1–2.5 mm deep in 5 mm thick plates) were introduced at the Al-side interface of specimens fabricated with an Al-offset tool. Experiments and numerical simulations were used to evaluate wave modes and irradiation configurations, focusing on intensity-attenuation ratios of specific wave types, including longitudinal and Rayleigh waves. On the non-slit surface, attenuation of reflected longitudinal waves enabled detection of defects ≥0.5 mm deep. On the slit surface, Rayleigh-wave attenuation allowed identification of defects as shallow as 0.1 mm, although slit-side irradiation may be less practical during joining. These results demonstrate that defect identification in dissimilar materials can be achieved by evaluating wave-intensity attenuation rather than relying solely on the presence of reflected echoes, suggesting potential for implementing laser ultrasonics in in-process monitoring of FSW joints.
- Open Access
- 26 December 2025
- Published by MDPI AG in Applied Sciences
- Vol. 16 (1) , 281
Development of Laser Ultrasonic Robotic System for In Situ Internal Defect Detection
Assurance of the integrity of every weld joint is highly desirable, and defect detection methods that can be applied to welds at high temperatures immediately after welding are required. The laser ultrasonic (LU) method, which generates ultrasonic waves in the target via pulsed laser irradiation, is a well-known technique for non-contact defect detection during welding. Ultrasonic waves excited in ablation mode exhibit large amplitudes and predominantly surface-normal propagation, which has driven extensive research into their application for weld inspection. However, owing to the size and weight of conventional equipment, such systems have largely been limited to bench-top experimental setups. To address this, we developed an LU robotic system incorporating a compact, lightweight laser source and an improved signal-processing system. We conducted experiments to measure signals and to detect backside slits in flat plates and blowholes in lap-fillet welds. Additionally, a method to improve the sensitivity of laser interferometers was investigated and demonstrated on smut-covered areas near weld beads.
- 26 December 2025
- Published by MDPI AG in Applied Sciences
- Vol. 16 (1) , 281
Open AccessDevelopment of Laser Ultrasonic Robotic System for In Situ Internal Defect Detection
Assurance of the integrity of every weld joint is highly desirable, and defect detection methods that can be applied to welds at high temperatures immediately after welding are required. The laser ultrasonic (LU) method, which generates ultrasonic waves in the target via pulsed laser irradiation, is a well-known technique for non-contact defect detection during welding. Ultrasonic waves excited in ablation mode exhibit large amplitudes and predominantly surface-normal propagation, which has driven extensive research into their application for weld inspection. However, owing to the size and weight of conventional equipment, such systems have largely been limited to bench-top experimental setups. To address this, we developed an LU robotic system incorporating a compact, lightweight laser source and an improved signal-processing system. We conducted experiments to measure signals and to detect backside slits in flat plates and blowholes in lap-fillet welds. Additionally, a method to improve the sensitivity of laser interferometers was investigated and demonstrated on smut-covered areas near weld beads.
- Open Access
- 10 March 2024
- Published by Sumart Processing Society for Minerals, Environment and Energy in Journal of Smart Processing
- Vol. 13 (2) , 75-81
Development of Dynamic Laser Ultrasonic System Using Microchip Laser Mounted on a Robot Arm
The laser ultrasonic method is highly applicable to in-process and in-line measurement as a technology that enables non-contact ultrasonic detection. Previous studies have reported measurements using laser ultrasonic for various applications, however, most were measurements using fixed systems. There is a need for a dynamic UT system in which the laser ultrasonic measurement system itself can move. Therefore, we made it possible to mount the laser system on a robot arm by using a compact microchip laser as the ultrasonic generation source. We measured the artificial back surface slit and verified its detectability performance as a dynamic robot UT system.
- 10 March 2024
- Published by Sumart Processing Society for Minerals, Environment and Energy in Journal of Smart Processing
- Vol. 13 (2) , 75-81
Open AccessDevelopment of Dynamic Laser Ultrasonic System Using Microchip Laser Mounted on a Robot Arm
The laser ultrasonic method is highly applicable to in-process and in-line measurement as a technology that enables non-contact ultrasonic detection. Previous studies have reported measurements using laser ultrasonic for various applications, however, most were measurements using fixed systems. There is a need for a dynamic UT system in which the laser ultrasonic measurement system itself can move. Therefore, we made it possible to mount the laser system on a robot arm by using a compact microchip laser as the ultrasonic generation source. We measured the artificial back surface slit and verified its detectability performance as a dynamic robot UT system.
- Open Access
- 20 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (20) , 11515
Study on Detecting Method of Internal Defects by Laser Ultrasonics in Lap Joint Welding of Galvanized Steel Sheet and Finite Element Analysis of Its Detectability
Blowholes caused by vaporization of the galvanized layer are a problem with galvanized steel sheets, which use lap joint welding. The laser ultrasonic method is the possible solution to realize the desirable 100% inspection instead of the conventional sampling inspection. We have previously proposed a method to detect blowholes by capturing the reduction in ultrasonic intensity when it passes through internal defects through signal processing. However, there was a problem that the detection indicator devised varied. In this study, we investigated the causes and trends of detectability using finite element analysis. To efficiently calculate the results obtained by scanning measurement, we proposed and established a method to reproduce the results by taking the results from static measurements, which were shifted in the direction of the weld line little by little. As a result, it was found that one of the reasons for the detection indicator variation with scanning by the lasers is the three-dimensional positional relationship between the blowhole and the scanning measurement line. In addition, it was possible to propose the performance required for the ultrasonic generation laser such as the traveling speed and the repetition frequency by back-calculating the spatial resolution from the rate of detection needed.
- 20 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (20) , 11515
Open AccessStudy on Detecting Method of Internal Defects by Laser Ultrasonics in Lap Joint Welding of Galvanized Steel Sheet and Finite Element Analysis of Its Detectability
Blowholes caused by vaporization of the galvanized layer are a problem with galvanized steel sheets, which use lap joint welding. The laser ultrasonic method is the possible solution to realize the desirable 100% inspection instead of the conventional sampling inspection. We have previously proposed a method to detect blowholes by capturing the reduction in ultrasonic intensity when it passes through internal defects through signal processing. However, there was a problem that the detection indicator devised varied. In this study, we investigated the causes and trends of detectability using finite element analysis. To efficiently calculate the results obtained by scanning measurement, we proposed and established a method to reproduce the results by taking the results from static measurements, which were shifted in the direction of the weld line little by little. As a result, it was found that one of the reasons for the detection indicator variation with scanning by the lasers is the three-dimensional positional relationship between the blowhole and the scanning measurement line. In addition, it was possible to propose the performance required for the ultrasonic generation laser such as the traveling speed and the repetition frequency by back-calculating the spatial resolution from the rate of detection needed.
- Open Access
- 12 October 2023
- Published by Elsevier in NDT & E International
- Vol. 140
Study on non-contact measurement method of resistance spot weld nugget diameter using laser ultrasonic technique
- 12 October 2023
- Published by Elsevier in NDT & E International
- Vol. 140
Open AccessStudy on non-contact measurement method of resistance spot weld nugget diameter using laser ultrasonic technique
- 22 July 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (11) , 2271-2280
Fundamental study of the quality measurement for wire arc additive manufacturing process by laser ultrasonic technique
- 22 July 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (11) , 2271-2280
Fundamental study of the quality measurement for wire arc additive manufacturing process by laser ultrasonic technique
- Open Access
- 13 May 2022
- Published by Elsevier in NDT & E International
- Vol. 130
In situ measurement of ultrasonic behavior during lap spot welding with laser ultrasonic method
- 13 May 2022
- Published by Elsevier in NDT & E International
- Vol. 130
Open AccessIn situ measurement of ultrasonic behavior during lap spot welding with laser ultrasonic method
- 3 June 2021
- Published by Taylor & Francis in Welding International
- Vol. 35 (4-6) , 214-229
In-process monitoring of welding quality by robotic laser ultrasonic measurement system using microchip laser
Laser ultrasonic technique (LUT) is applicable even in a high temperature state such as during welding because the laser is irradiated remotely without contact. Recent studies have reported that LUT is applicable during welding, and it is effective for in-process monitoring. However, in the previous studies, there was a problem with the portability of the measurement device especially in a generation laser, so the scope of its application was limited. In this study, we constructed a robotic measurement system of laser ultrasonic with a small microchip laser mounted on a robotic arm. Microchip laser, which is a prototype product (1064 nm, 20 mJ/pulse, 1.5 ns, 20 Hz), was used to generate ultrasonic, and a laser interferometer (532 nm, 1 W) was used to detect the surface micro-vibration caused by the arrival of ultrasonic wave and was scanned using an uniaxial stage. After acquiring the B scope, which is composed of a generation point and multi-detection points, the synthetic aperture focussing technique (SAFT) is applied. SAFT image obtained by in-process measurement was evaluated to confirm the presence or absence of welding defect indication. Then, during gas metal arc (GMA) welding process in the mid-pass of a multi-layer welding for a single bevel groove, we attempted to detect welding defects generated by introducing slits before welding. As a result, in the second pass, defects were indicated in all areas where defects existed, and no indications were found in areas without defects. Therefore, it was shown that the robotic laser ultrasonic measurement system constructed in this study can detect defects in the process of welding. In conclusion, we were able to show the possibility of evaluating the welding quality in the process of welding even at the construction site by selecting the appropriate generation position and detection range according to the required accuracy and laser specifications.
- 3 June 2021
- Published by Taylor & Francis in Welding International
- Vol. 35 (4-6) , 214-229
In-process monitoring of welding quality by robotic laser ultrasonic measurement system using microchip laser
Laser ultrasonic technique (LUT) is applicable even in a high temperature state such as during welding because the laser is irradiated remotely without contact. Recent studies have reported that LUT is applicable during welding, and it is effective for in-process monitoring. However, in the previous studies, there was a problem with the portability of the measurement device especially in a generation laser, so the scope of its application was limited. In this study, we constructed a robotic measurement system of laser ultrasonic with a small microchip laser mounted on a robotic arm. Microchip laser, which is a prototype product (1064 nm, 20 mJ/pulse, 1.5 ns, 20 Hz), was used to generate ultrasonic, and a laser interferometer (532 nm, 1 W) was used to detect the surface micro-vibration caused by the arrival of ultrasonic wave and was scanned using an uniaxial stage. After acquiring the B scope, which is composed of a generation point and multi-detection points, the synthetic aperture focussing technique (SAFT) is applied. SAFT image obtained by in-process measurement was evaluated to confirm the presence or absence of welding defect indication. Then, during gas metal arc (GMA) welding process in the mid-pass of a multi-layer welding for a single bevel groove, we attempted to detect welding defects generated by introducing slits before welding. As a result, in the second pass, defects were indicated in all areas where defects existed, and no indications were found in areas without defects. Therefore, it was shown that the robotic laser ultrasonic measurement system constructed in this study can detect defects in the process of welding. In conclusion, we were able to show the possibility of evaluating the welding quality in the process of welding even at the construction site by selecting the appropriate generation position and detection range according to the required accuracy and laser specifications.
- Open Access
- 1 January 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 61, 590-600
Burn-through prediction and weld depth estimation by deep learning model monitoring the molten pool in gas metal arc welding with gap fluctuation
- 1 January 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 61, 590-600
Open AccessBurn-through prediction and weld depth estimation by deep learning model monitoring the molten pool in gas metal arc welding with gap fluctuation
- 1 January 2020
- Published by Japan Welding Society in JOURNAL OF THE JAPAN WELDING SOCIETY
- Vol. 89 (1) , 87-94
Inspection and Monitoring of Weld using Laser Ultrasonics
- 1 January 2020
- Published by Japan Welding Society in JOURNAL OF THE JAPAN WELDING SOCIETY
- Vol. 89 (1) , 87-94
Inspection and Monitoring of Weld using Laser Ultrasonics