Satoru Asai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Satoru Asai has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Kazufumi Nomura
Division of Materials and Manufacturing Science, Graduate School of Engineering, The University of Osaka, Osaka 565-0871, Japan
4 shared publications - Yosuke Ogino
Graduate School of Engineering, Osaka University, Suita, Japan
3 shared publications - Keiji Kadota
DAIHEN Welding and Joining Research Alliance Laboratories, Joining and Welding Research Institute, The University of Osaka, Osaka 567-0047, Japan
2 shared publications - Seiya Nitta
DAIHEN Welding and Joining Research Alliance Laboratories, Joining and Welding Research Institute, The University of Osaka, Osaka 567-0047, Japan
2 shared publications - Tetsuo Era
DAIHEN Welding and Joining Research Alliance Laboratories, Joining and Welding Research Institute, The University of Osaka, Osaka 567-0047, Japan
2 shared publications Yasuhiro Konishi
Department of Chemical Engineering, Osaka Prefecture University, 1-1 Gaknen-cho, Sakai, Osaka 593, Japan
2 shared publications
Latest Publications
- Open Access
- 9 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (2) , 688
Study on Non-Contact Defect Detection Using the Laser Ultrasonic Method for Friction Stir-Welded Cu–Al Dissimilar Material Joints
Ensuring friction stir welding (FSW) joint quality typically relies on ultrasonic testing (UT) and radiographic testing (RT), but achieving complete coverage is challenging, and echo-based defect discrimination becomes difficult in dissimilar joints. Laser ultrasonics is a promising non-contact technique that remotely assesses weld quality and provides high spatial resolution at the generation and detection points. This study establishes a laser-ultrasonic method for defect detection in dissimilar Cu–Al FSW joints. Slit-like artificial defects (0.1–2.5 mm deep in 5 mm thick plates) were introduced at the Al-side interface of specimens fabricated with an Al-offset tool. Experiments and numerical simulations were used to evaluate wave modes and irradiation configurations, focusing on intensity-attenuation ratios of specific wave types, including longitudinal and Rayleigh waves. On the non-slit surface, attenuation of reflected longitudinal waves enabled detection of defects ≥0.5 mm deep. On the slit surface, Rayleigh-wave attenuation allowed identification of defects as shallow as 0.1 mm, although slit-side irradiation may be less practical during joining. These results demonstrate that defect identification in dissimilar materials can be achieved by evaluating wave-intensity attenuation rather than relying solely on the presence of reflected echoes, suggesting potential for implementing laser ultrasonics in in-process monitoring of FSW joints.
- 9 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (2) , 688
Open AccessStudy on Non-Contact Defect Detection Using the Laser Ultrasonic Method for Friction Stir-Welded Cu–Al Dissimilar Material Joints
Ensuring friction stir welding (FSW) joint quality typically relies on ultrasonic testing (UT) and radiographic testing (RT), but achieving complete coverage is challenging, and echo-based defect discrimination becomes difficult in dissimilar joints. Laser ultrasonics is a promising non-contact technique that remotely assesses weld quality and provides high spatial resolution at the generation and detection points. This study establishes a laser-ultrasonic method for defect detection in dissimilar Cu–Al FSW joints. Slit-like artificial defects (0.1–2.5 mm deep in 5 mm thick plates) were introduced at the Al-side interface of specimens fabricated with an Al-offset tool. Experiments and numerical simulations were used to evaluate wave modes and irradiation configurations, focusing on intensity-attenuation ratios of specific wave types, including longitudinal and Rayleigh waves. On the non-slit surface, attenuation of reflected longitudinal waves enabled detection of defects ≥0.5 mm deep. On the slit surface, Rayleigh-wave attenuation allowed identification of defects as shallow as 0.1 mm, although slit-side irradiation may be less practical during joining. These results demonstrate that defect identification in dissimilar materials can be achieved by evaluating wave-intensity attenuation rather than relying solely on the presence of reflected echoes, suggesting potential for implementing laser ultrasonics in in-process monitoring of FSW joints.
- Open Access
- 26 December 2025
- Published by MDPI AG in Applied Sciences
- Vol. 16 (1) , 281
Development of Laser Ultrasonic Robotic System for In Situ Internal Defect Detection
Assurance of the integrity of every weld joint is highly desirable, and defect detection methods that can be applied to welds at high temperatures immediately after welding are required. The laser ultrasonic (LU) method, which generates ultrasonic waves in the target via pulsed laser irradiation, is a well-known technique for non-contact defect detection during welding. Ultrasonic waves excited in ablation mode exhibit large amplitudes and predominantly surface-normal propagation, which has driven extensive research into their application for weld inspection. However, owing to the size and weight of conventional equipment, such systems have largely been limited to bench-top experimental setups. To address this, we developed an LU robotic system incorporating a compact, lightweight laser source and an improved signal-processing system. We conducted experiments to measure signals and to detect backside slits in flat plates and blowholes in lap-fillet welds. Additionally, a method to improve the sensitivity of laser interferometers was investigated and demonstrated on smut-covered areas near weld beads.
- 26 December 2025
- Published by MDPI AG in Applied Sciences
- Vol. 16 (1) , 281
Open AccessDevelopment of Laser Ultrasonic Robotic System for In Situ Internal Defect Detection
Assurance of the integrity of every weld joint is highly desirable, and defect detection methods that can be applied to welds at high temperatures immediately after welding are required. The laser ultrasonic (LU) method, which generates ultrasonic waves in the target via pulsed laser irradiation, is a well-known technique for non-contact defect detection during welding. Ultrasonic waves excited in ablation mode exhibit large amplitudes and predominantly surface-normal propagation, which has driven extensive research into their application for weld inspection. However, owing to the size and weight of conventional equipment, such systems have largely been limited to bench-top experimental setups. To address this, we developed an LU robotic system incorporating a compact, lightweight laser source and an improved signal-processing system. We conducted experiments to measure signals and to detect backside slits in flat plates and blowholes in lap-fillet welds. Additionally, a method to improve the sensitivity of laser interferometers was investigated and demonstrated on smut-covered areas near weld beads.
- Open Access
- 20 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (20) , 11515
Study on Detecting Method of Internal Defects by Laser Ultrasonics in Lap Joint Welding of Galvanized Steel Sheet and Finite Element Analysis of Its Detectability
Blowholes caused by vaporization of the galvanized layer are a problem with galvanized steel sheets, which use lap joint welding. The laser ultrasonic method is the possible solution to realize the desirable 100% inspection instead of the conventional sampling inspection. We have previously proposed a method to detect blowholes by capturing the reduction in ultrasonic intensity when it passes through internal defects through signal processing. However, there was a problem that the detection indicator devised varied. In this study, we investigated the causes and trends of detectability using finite element analysis. To efficiently calculate the results obtained by scanning measurement, we proposed and established a method to reproduce the results by taking the results from static measurements, which were shifted in the direction of the weld line little by little. As a result, it was found that one of the reasons for the detection indicator variation with scanning by the lasers is the three-dimensional positional relationship between the blowhole and the scanning measurement line. In addition, it was possible to propose the performance required for the ultrasonic generation laser such as the traveling speed and the repetition frequency by back-calculating the spatial resolution from the rate of detection needed.
- 20 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (20) , 11515
Open AccessStudy on Detecting Method of Internal Defects by Laser Ultrasonics in Lap Joint Welding of Galvanized Steel Sheet and Finite Element Analysis of Its Detectability
Blowholes caused by vaporization of the galvanized layer are a problem with galvanized steel sheets, which use lap joint welding. The laser ultrasonic method is the possible solution to realize the desirable 100% inspection instead of the conventional sampling inspection. We have previously proposed a method to detect blowholes by capturing the reduction in ultrasonic intensity when it passes through internal defects through signal processing. However, there was a problem that the detection indicator devised varied. In this study, we investigated the causes and trends of detectability using finite element analysis. To efficiently calculate the results obtained by scanning measurement, we proposed and established a method to reproduce the results by taking the results from static measurements, which were shifted in the direction of the weld line little by little. As a result, it was found that one of the reasons for the detection indicator variation with scanning by the lasers is the three-dimensional positional relationship between the blowhole and the scanning measurement line. In addition, it was possible to propose the performance required for the ultrasonic generation laser such as the traveling speed and the repetition frequency by back-calculating the spatial resolution from the rate of detection needed.
- 1 January 2020
- Published by Japan Welding Society in JOURNAL OF THE JAPAN WELDING SOCIETY
- Vol. 89 (1) , 87-94
Inspection and Monitoring of Weld using Laser Ultrasonics
- 1 January 2020
- Published by Japan Welding Society in JOURNAL OF THE JAPAN WELDING SOCIETY
- Vol. 89 (1) , 87-94
Inspection and Monitoring of Weld using Laser Ultrasonics
- Open Access
- 1 January 2019
- Published by Japan Welding Society in QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY
- Vol. 37 (3) , 108-114
Fundamental Study on On-line Image Sensing Technology of Arc Welding
- 1 January 2019
- Published by Japan Welding Society in QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY
- Vol. 37 (3) , 108-114
Open AccessFundamental Study on On-line Image Sensing Technology of Arc Welding
- 18 June 2018
- Published by Springer Nature in Welding in the World
- Vol. 62 (5) , 1021-1030
Numerical study of the influence of gap between plates on weld pool formation in arc spot welding process
- 18 June 2018
- Published by Springer Nature in Welding in the World
- Vol. 62 (5) , 1021-1030
Numerical study of the influence of gap between plates on weld pool formation in arc spot welding process
- 20 June 2017
- Published by Springer Nature in Welding in the World
- Vol. 61 (6) , 1289-1296
Numerical simulation of metal transfer in pulsed-MIG welding
- 20 June 2017
- Published by Springer Nature in Welding in the World
- Vol. 61 (6) , 1289-1296
Numerical simulation of metal transfer in pulsed-MIG welding
- 19 March 1998
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 37 (6) , 2093-2098
Precipitation Stripping of Yttrium Oxalate Powders from Yttrium-Loaded Carboxylate Solutions with Aqueous Oxalic Acid Solutions
- 19 March 1998
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 37 (6) , 2093-2098
Precipitation Stripping of Yttrium Oxalate Powders from Yttrium-Loaded Carboxylate Solutions with Aqueous Oxalic Acid Solutions
- Open Access
- 1 January 1994
- Published by Japan Institute of Metals in Materials Transactions, JIM
- Vol. 35 (10) , 695-698
Leaching of Copper from Natural Covellite in Alkaline Na4EDTA Solutions
- 1 January 1994
- Published by Japan Institute of Metals in Materials Transactions, JIM
- Vol. 35 (10) , 695-698
Open AccessLeaching of Copper from Natural Covellite in Alkaline Na4EDTA Solutions