L. J. Ernst
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
L. J. Ernst has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- G. Q. Zhang
Delft University of Technology
4 shared publications H. J. L. Bressers
Philips, P.O. Box 218, 5600 MD Eindhoven, The Netherlands
1 shared publicationJ. H. J. Janssen
Philips Semiconductors, ATO Innovation, P.O. Box 30008, 6534 AE Nijmegen, The Netherlands
1 shared publication- Jiang Zhou
Lamar University
1 shared publication - Kaspar M. B. Jansen
Faculty of Industrial Design Engineering, Delft University of Technology, Landbergstraat 15, 2628 CE Delft, The Netherlands
1 shared publication - V Rizov
Department of Technical Mechanics, Civil Engineering and Geodesy, University of Architecture, Chr. Smirnensky 1, Sofia 1421, Bulgaria
1 shared publication
Latest Publications
- 1 December 2004
- Published by ASME International in Journal of Electronic Packaging
- Vol. 127 (4) , 530-536
State-of-the-Art of Thermo-Mechanical Characterization of Thin Polymer Films
In microelectronic industry, thin polymer layers are one of the more commonly used product constituents. Examples are glue layers, coatings, and dielectric layers. The thicknesses of these films vary from a few tens of nanometers to over a hundred micrometers. Since at film thicknesses below 100nm the thermal and mechanical properties start to deviate from those in the bulk, adequate characterization techniques are required. In the present paper we will report the results of an extensive literature search on the state-of-the-art of thermo-mechanical thin film characterization methods, such as the substrate curvature test, nanoindentation technique, bulge test, and impulsive stimulated thermal scattering.
- 1 December 2004
- Published by ASME International in Journal of Electronic Packaging
- Vol. 127 (4) , 530-536
State-of-the-Art of Thermo-Mechanical Characterization of Thin Polymer Films
In microelectronic industry, thin polymer layers are one of the more commonly used product constituents. Examples are glue layers, coatings, and dielectric layers. The thicknesses of these films vary from a few tens of nanometers to over a hundred micrometers. Since at film thicknesses below 100nm the thermal and mechanical properties start to deviate from those in the bulk, adequate characterization techniques are required. In the present paper we will report the results of an extensive literature search on the state-of-the-art of thermo-mechanical thin film characterization methods, such as the substrate curvature test, nanoindentation technique, bulge test, and impulsive stimulated thermal scattering.
- 26 June 2004
- Published by ASME International in Journal of Electronic Packaging
- Vol. 127 (3) , 262-267
A Micromechanics-Based Vapor Pressure Model in Electronic Packages
A complete vapor pressure model based on a micromechanics approach is developed in this paper. The model can be extended to calculate the initial vapor pressure as traction loading subjected to the interfaces after the delamination. The impact of the vapor pressure induced expanison on the material’s deformation is discussed.
- 26 June 2004
- Published by ASME International in Journal of Electronic Packaging
- Vol. 127 (3) , 262-267
A Micromechanics-Based Vapor Pressure Model in Electronic Packages
A complete vapor pressure model based on a micromechanics approach is developed in this paper. The model can be extended to calculate the initial vapor pressure as traction loading subjected to the interfaces after the delamination. The impact of the vapor pressure induced expanison on the material’s deformation is discussed.
- Open Access
- 1 December 2003
- Published by ASME International in Journal of Electronic Packaging
- Vol. 125 (4) , 465
Thermal and Mechanical Simulation and Experiments in Micro-electronics and Microsystems
- 1 December 2003
- Published by ASME International in Journal of Electronic Packaging
- Vol. 125 (4) , 465
Open AccessThermal and Mechanical Simulation and Experiments in Micro-electronics and Microsystems
- 1 December 2003
- Published by ASME International in Journal of Electronic Packaging
- Vol. 125 (4) , 490-497
Response Surface Modeling for Nonlinear Packaging Stresses
The present study focuses on the development of reliable response surface models (RSM’s) for the major packaging processes of a typical electronic package. The major objective is to optimize the product/process designs against the possible failure mode of vertical die cracks. First, the finite element mode (FEM)-based physics of failure models are developed and the reliability of the predicted stress levels was verified by experiments. In the development of reliable thermo-mechanical simulation models, both the process (time and temperature) dependent material nonlinearity and geometric nonlinearity are taken into account. Afterwards, RSM’s covering the whole specified geometric design spaces are constructed. Finally, these RSM’s are used to predict, evaluate, optimize, and eventually qualify the thermo-mechanical behavior of this electronic package against the actual design requirements prior to major physical prototyping and manufacturing investments.
- 1 December 2003
- Published by ASME International in Journal of Electronic Packaging
- Vol. 125 (4) , 490-497
Response Surface Modeling for Nonlinear Packaging Stresses
The present study focuses on the development of reliable response surface models (RSM’s) for the major packaging processes of a typical electronic package. The major objective is to optimize the product/process designs against the possible failure mode of vertical die cracks. First, the finite element mode (FEM)-based physics of failure models are developed and the reliability of the predicted stress levels was verified by experiments. In the development of reliable thermo-mechanical simulation models, both the process (time and temperature) dependent material nonlinearity and geometric nonlinearity are taken into account. Afterwards, RSM’s covering the whole specified geometric design spaces are constructed. Finally, these RSM’s are used to predict, evaluate, optimize, and eventually qualify the thermo-mechanical behavior of this electronic package against the actual design requirements prior to major physical prototyping and manufacturing investments.
- 31 December 2001
- Published by Elsevier in Composite Structures
- Vol. 54 (2-3) , 331-334
On the analysis of the interlaminar strain-energy release rates in ring-fracture-test specimens
- 31 December 2001
- Published by Elsevier in Composite Structures
- Vol. 54 (2-3) , 331-334
On the analysis of the interlaminar strain-energy release rates in ring-fracture-test specimens