G. Q. Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
G. Q. Zhang has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Willem Dirk van Driel
Delft University of Technology
10 shared publications - Xuejun Fan
Department of Mechanical Engineering, Lamar University, Beaumont, USA
5 shared publications - L. J. Ernst
Delft University of Technology, Mekelweg 2, 2628 CD Delft, The Netherlands
4 shared publications - Cadmus Yuan
Delft University of Technology
3 shared publications - B. A. E. van Hal
Department of Mechanical Engineering, Eindhoven University of Technology, P.O. Box 513, 5600 MB Eindhoven, The Netherlands
2 shared publications - Jiang Zhou
Lamar University
2 shared publications
Latest Publications
- 23 September 2018
- Published by Springer Nature
- p. 129-183
Advances in Delamination Modeling of Metal/Polymer Systems: Atomistic Aspects
- 23 September 2018
- Published by Springer Nature
- p. 129-183
Advances in Delamination Modeling of Metal/Polymer Systems: Atomistic Aspects
- 18 July 2012
- Published by Springer Nature
- p. 395-412
Fault Tolerant Control of Large LED Systems
- 1 July 2012
- Published by Elsevier in Microelectronics Reliability
- Vol. 52 (7) , 1279-1284
Effects of single vacancy defect position on the stability of carbon nanotubes
- 1 July 2012
- Published by Elsevier in Microelectronics Reliability
- Vol. 52 (7) , 1279-1284
Effects of single vacancy defect position on the stability of carbon nanotubes
- 1 January 2011
- Published by IOP Publishing in Journal of Semiconductors
- Vol. 32 (1) , 45-48
Degradation of light emitting diodes: a proposed methodology
Due to their long lifetime and high efficacy,light emitting diodes have the potential to revolutionize the illumination industry.However,self heat and high environmental temperature which will lead to increased junction temperature and degradation due to electrical overstress can shorten the life of the light emitting diode.In this research,a methodology to investigate the degradation of the LED emitter has been proposed.The epoxy lens of the emitter can be modelled using simplified Eyring methods whereas an equation has been proposed for describing the degradation of the LED emitters.
- 1 January 2011
- Published by IOP Publishing in Journal of Semiconductors
- Vol. 32 (1) , 45-48
Degradation of light emitting diodes: a proposed methodology
Due to their long lifetime and high efficacy,light emitting diodes have the potential to revolutionize the illumination industry.However,self heat and high environmental temperature which will lead to increased junction temperature and degradation due to electrical overstress can shorten the life of the light emitting diode.In this research,a methodology to investigate the degradation of the LED emitter has been proposed.The epoxy lens of the emitter can be modelled using simplified Eyring methods whereas an equation has been proposed for describing the degradation of the LED emitters.
- 14 May 2010
- Published by Springer Nature
- p. 435-460
Underfill Selection Against Moisture in Flip Chip BGA Packages
- 14 May 2010
- Published by Springer Nature
- p. 435-460
Underfill Selection Against Moisture in Flip Chip BGA Packages
- 14 May 2010
- Published by Springer Nature
- p. 411-434
Industrial Applications of Moisture-Related Reliability Problems
- 14 May 2010
- Published by Springer Nature
- p. 411-434
Industrial Applications of Moisture-Related Reliability Problems
- 14 May 2010
- Published by Springer Nature
- p. 279-299
Continuum Theory in Moisture-Induced Failures of Encapsulated IC Devices
- 14 May 2010
- Published by Springer Nature
- p. 279-299
Continuum Theory in Moisture-Induced Failures of Encapsulated IC Devices
- 4 August 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 9 (1) , 2-8
On Wire Failures in Microelectronic Packages
At present, over 95% of the manufactured packages are still being wire-bonded. Due to the ongoing trend of miniaturization, material changes, and cost reduction, wire-bond-related failures are becoming increasingly important. Different finite-element (FE) techniques are explored for their ability to describe the thermomechanical behavior of the wire embedded in the electronic package. The developed nonlinear and parametric FE models are able to predict the strong nonlinear behavior of wire failures and multifailure-mode interaction accurately and efficiently. It is found that both processing and reliability-testing environments as well as the occurrence of delamination strongly increase the risk of wire failures. Our results indicate that processing and reliability-testing influences are much less than those of the delamination. Combining the strengths of predictive modeling with simulation-based optimization methods, the optimal wire-loop shape is obtained.
- 4 August 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 9 (1) , 2-8
On Wire Failures in Microelectronic Packages
At present, over 95% of the manufactured packages are still being wire-bonded. Due to the ongoing trend of miniaturization, material changes, and cost reduction, wire-bond-related failures are becoming increasingly important. Different finite-element (FE) techniques are explored for their ability to describe the thermomechanical behavior of the wire embedded in the electronic package. The developed nonlinear and parametric FE models are able to predict the strong nonlinear behavior of wire failures and multifailure-mode interaction accurately and efficiently. It is found that both processing and reliability-testing environments as well as the occurrence of delamination strongly increase the risk of wire failures. Our results indicate that processing and reliability-testing influences are much less than those of the delamination. Combining the strengths of predictive modeling with simulation-based optimization methods, the optimal wire-loop shape is obtained.
- 1 August 2008
- Published by Elsevier in Microelectronics Reliability
- Vol. 48 (8-9) , 1268-1272
On chip–package stress interaction
- 1 August 2008
- Published by Elsevier in Microelectronics Reliability
- Vol. 48 (8-9) , 1268-1272
On chip–package stress interaction