Oumarou Savadogo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Oumarou Savadogo has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- A. Samson Myles
Ecole Polytech Montreal, Dept Genie Chim, Lab New Mat Energy, Montreal, PQ, Canada
2 shared publications F. Fouda-Onana
Laboratoire de nouveaux matériaux pour les systèmes électrochimiques et énergétiques, Ecole Polytechnique de Montréal, Montréal, Québec, Canada H3C 3A7
2 shared publicationsKentaro Oishi
Cole Polytech Montreal, Lab New Mat Energy, Dept Genie Chim, Montreal, PQ, Canada
2 shared publicationsM. Talebi-Esfandarani
École Polytechnque de Montréal
2 shared publications- Rachid Boukhili
Polytechnique Montreal
2 shared publications - Wend-Waoga Anthelme Zemane
Laboratory of New Materials for Energy and Electrochemistry, Polytechnique Montreal, Montreal, QC H3T 1J4, Canada
2 shared publications
Latest Publications
- Open Access
A New Power Dissipation Model and Its Analytic Formulation for Electric-Field-Driven Water Dissociation in the Cationic/Anionic Bipolar Polymer Membrane Junctions
Bipolar Polymer Membranes (BPMs) enable the creation of large, stable pH gradients by driving water dissociation (WD) at the cation/anion junction under reverse bias, a process central to electrodialysis, CO2 capture, and emerging acid–alkaline water electrolysis. Yet despite decades of study, the mechanism by which intense interfacial electric fields accelerate WD remains debated and is often modeled with ad hoc assumptions. In this study, we present a power dissipation model in which minority ions from water autoprotolysis act as carriers that continuously dissipate field-supplied power in the hydrated nanometric junction. This dissipative input increases the local probability of heterolytic O–H bond cleavage and analytically leads to a quadratic dependence of the dissociation rate constant on the field. Without adjustable parameters, the model reproduces the required orders of magnitude for the enhancement ratio kd(E)/kd(0), where kd(E) is the field-enhanced water dissociation rate constant and kd(0) is its zero-field value across typical BPM fields, and yields a quadratic current–voltage junction law. A proof-of-principle measurement on a commercial Fumasep® FBM bipolar membrane confirms the quadratic current–voltage trend, supporting a power-dissipation-driven water dissociation mechanism and providing a concise, falsifiable baseline for future studies.
Open AccessA New Power Dissipation Model and Its Analytic Formulation for Electric-Field-Driven Water Dissociation in the Cationic/Anionic Bipolar Polymer Membrane Junctions
Bipolar Polymer Membranes (BPMs) enable the creation of large, stable pH gradients by driving water dissociation (WD) at the cation/anion junction under reverse bias, a process central to electrodialysis, CO2 capture, and emerging acid–alkaline water electrolysis. Yet despite decades of study, the mechanism by which intense interfacial electric fields accelerate WD remains debated and is often modeled with ad hoc assumptions. In this study, we present a power dissipation model in which minority ions from water autoprotolysis act as carriers that continuously dissipate field-supplied power in the hydrated nanometric junction. This dissipative input increases the local probability of heterolytic O–H bond cleavage and analytically leads to a quadratic dependence of the dissociation rate constant on the field. Without adjustable parameters, the model reproduces the required orders of magnitude for the enhancement ratio kd(E)/kd(0), where kd(E) is the field-enhanced water dissociation rate constant and kd(0) is its zero-field value across typical BPM fields, and yields a quadratic current–voltage junction law. A proof-of-principle measurement on a commercial Fumasep® FBM bipolar membrane confirms the quadratic current–voltage trend, supporting a power-dissipation-driven water dissociation mechanism and providing a concise, falsifiable baseline for future studies.
- Open Access
- 1 December 2025
- Published by MDPI AG in Preprints.org
Proposition of a New Power Dissipation Model and Its Analytic Formulation for Electric-Field-Driven Water Dissociation in the Cationic/ Anionic Bipolar Polymer Membranes Junctions
Bipolar Polymer Membranes (BPMs) enable the creation of large, stable pH gradients by drivingwater dissociation (WD) at the cation/anion junction under reverse bias, a process central to electrodialysis, CO₂ capture, and emerging acid–alkaline water electrolysis. Yet, despite decades of study, the mechanism by which intense interfacial electric fields accelerate WD remains debated and is often modeled with ad hoc assumptions. Here, we outline key limitations of existing models of field-enhanced WD in BPMs and we present a power-dissipation model and its formalism that address them. In this new framework, we emphasize that minority ions from water autoprotolysis act as carriers that continuously dissipate field-supplied power in the hydrated nanometric junction. This dissipative input raises the local probability of heterolytic O–H bond cleavage and leads analytically to the dissociation rate’s quadratic dependence on the field. Without adjustable parameters, the model reproduces the required orders of magnitude for the enhancement ratio kd(E)/kd(0), where kd(E) is the field-enhanced water-dissociation rate constant and kd(0) its zero-field value, across typical BPM fields and yields a quadratic current–voltage junction law. A proof-of-principle measurement on a commercial Fumasep® FBM confirms the quadratic current–voltage trend, supporting a power dissipation field-driven WD and providing a concise, falsifiable baseline for future studies.
- 1 December 2025
- Published by MDPI AG in Preprints.org
Open AccessProposition of a New Power Dissipation Model and Its Analytic Formulation for Electric-Field-Driven Water Dissociation in the Cationic/ Anionic Bipolar Polymer Membranes Junctions
Bipolar Polymer Membranes (BPMs) enable the creation of large, stable pH gradients by drivingwater dissociation (WD) at the cation/anion junction under reverse bias, a process central to electrodialysis, CO₂ capture, and emerging acid–alkaline water electrolysis. Yet, despite decades of study, the mechanism by which intense interfacial electric fields accelerate WD remains debated and is often modeled with ad hoc assumptions. Here, we outline key limitations of existing models of field-enhanced WD in BPMs and we present a power-dissipation model and its formalism that address them. In this new framework, we emphasize that minority ions from water autoprotolysis act as carriers that continuously dissipate field-supplied power in the hydrated nanometric junction. This dissipative input raises the local probability of heterolytic O–H bond cleavage and leads analytically to the dissociation rate’s quadratic dependence on the field. Without adjustable parameters, the model reproduces the required orders of magnitude for the enhancement ratio kd(E)/kd(0), where kd(E) is the field-enhanced water-dissociation rate constant and kd(0) its zero-field value, across typical BPM fields and yields a quadratic current–voltage junction law. A proof-of-principle measurement on a commercial Fumasep® FBM confirms the quadratic current–voltage trend, supporting a power dissipation field-driven WD and providing a concise, falsifiable baseline for future studies.
- Open Access
Electrochemical Performances of Li-Ion Batteries Based on LiFePO4 Cathodes Supported by Bio-Sourced Activated Carbon from Millet Cob (MC) and Water Hyacinth (WH)
The electrochemical performance of Li-ion batteries employing LiFePO4 (LFP) cathodes supported by bio-sourced activated carbon derived from millet cob (MC) and water hyacinth (WH) were systematically investigated. Carbon activation was carried out using potassium hydroxide (KOH) at varying mass ratios of KOH to precursor material: 1:1, 2:1, and 5:1 for both WH and MC-derived carbon. The physical properties (X-ray diffraction patterns, BET surface area, micropore and mesopore volume, conductivity, etc.) and electrochemical performance (specific capacity, discharge at various current rates, electrochemical impedance measurement, etc.) were determined. Material characterization revealed that the activated carbon derived from MC exhibits an amorphous structure, whereas that obtained from WH is predominantly crystalline. High specific surface areas were achieved with activated carbons synthesized using a low KOH-to-carbon mass ratio (1:1), reaching 413.03 m2·g−1 for WH and 216.34 m2·g−1 for MC. However, larger average pore diameters were observed at higher activation ratios (5:1), measuring 8.38 nm for KOH/WH and 5.28 nm for KOH/MC. For both biomass-derived carbons, optimal electrical conductivity was obtained at a 2:1 activation ratio, with values of 14.7 × 10−3 S·cm−1 for KOH/WH and 8.42 × 10−3 S·cm−1 for KOH/MC. The electrochemical performance of coin cells based on cathodes composed of 85% LiFePO4, 8% of these activated carbons, and 7% polyvinylidene fluoride (PVDF) as a binder, with lithium metal as the anode were studied. The LiFePO4/C (LFP/C) cathodes exhibited specific capacities of up to 160 mAh·g−1 at a current rate of C/12 and 110 mAh·g−1 at 5C. Both LFP/MC and LFP/WH cathodes exhibit optimal energy density at specific values of pore size, pore volume, charge transfer resistance (Rct), and diffusion coefficient (DLi), reflecting a favorable balance between ionic transport, accessible surface area, and charge conduction. Maximum energy densities relative to active mass were recorded at 544 mWh·g−1 for LFP/MC 2:1, 554 mWh·g−1 for LFP/WH 2:1, and 568 mWh·g−1 for the reference LFP/graphite system. These performance results demonstrate that the development of high-performing bio-sourced activated carbon depends on the optimization of various parameters, including chemical composition, specific surface area, pore volume and size distribution, as well as electrical conductivity.
Open AccessElectrochemical Performances of Li-Ion Batteries Based on LiFePO4 Cathodes Supported by Bio-Sourced Activated Carbon from Millet Cob (MC) and Water Hyacinth (WH)
The electrochemical performance of Li-ion batteries employing LiFePO4 (LFP) cathodes supported by bio-sourced activated carbon derived from millet cob (MC) and water hyacinth (WH) were systematically investigated. Carbon activation was carried out using potassium hydroxide (KOH) at varying mass ratios of KOH to precursor material: 1:1, 2:1, and 5:1 for both WH and MC-derived carbon. The physical properties (X-ray diffraction patterns, BET surface area, micropore and mesopore volume, conductivity, etc.) and electrochemical performance (specific capacity, discharge at various current rates, electrochemical impedance measurement, etc.) were determined. Material characterization revealed that the activated carbon derived from MC exhibits an amorphous structure, whereas that obtained from WH is predominantly crystalline. High specific surface areas were achieved with activated carbons synthesized using a low KOH-to-carbon mass ratio (1:1), reaching 413.03 m2·g−1 for WH and 216.34 m2·g−1 for MC. However, larger average pore diameters were observed at higher activation ratios (5:1), measuring 8.38 nm for KOH/WH and 5.28 nm for KOH/MC. For both biomass-derived carbons, optimal electrical conductivity was obtained at a 2:1 activation ratio, with values of 14.7 × 10−3 S·cm−1 for KOH/WH and 8.42 × 10−3 S·cm−1 for KOH/MC. The electrochemical performance of coin cells based on cathodes composed of 85% LiFePO4, 8% of these activated carbons, and 7% polyvinylidene fluoride (PVDF) as a binder, with lithium metal as the anode were studied. The LiFePO4/C (LFP/C) cathodes exhibited specific capacities of up to 160 mAh·g−1 at a current rate of C/12 and 110 mAh·g−1 at 5C. Both LFP/MC and LFP/WH cathodes exhibit optimal energy density at specific values of pore size, pore volume, charge transfer resistance (Rct), and diffusion coefficient (DLi), reflecting a favorable balance between ionic transport, accessible surface area, and charge conduction. Maximum energy densities relative to active mass were recorded at 544 mWh·g−1 for LFP/MC 2:1, 554 mWh·g−1 for LFP/WH 2:1, and 568 mWh·g−1 for the reference LFP/graphite system. These performance results demonstrate that the development of high-performing bio-sourced activated carbon depends on the optimization of various parameters, including chemical composition, specific surface area, pore volume and size distribution, as well as electrical conductivity.
- Open Access
- 22 May 2025
- Published by MDPI AG in Preprints.org
Electrochemical Performances of Li-Ion Batteries Based on LiFePO4 Cathodes Supported by Bio-Sourced Activated Carbon from Millet Cob (MC) or Water Hyacinth (WH)
The electrochemical performances of Li-ion batteries based on LiFePO4(LFP) cathode supported by bio sourced activated carbon obtained from Millet Cob (MC) or Water Hyacinth (WH) were determined. The carbons were obtained by combustion prior to drying the raw materials of WH and MC, followed by steps of various chemical cleanings, were activated at the following different mass ratios of potassium hydroxide (KOH) and WH or MC respectively: KOH/WH 1:1, 2:1, and 5:1, and KOH/MC 1:1, 2:1, and 5:1.The physics properties (X-ray diffraction patterns, BET surface area, micropore and mesopore volume, conductivity, etc. ) and electrochemical performances (specific capacity, discharge at various current rates, electrochemical impedance measurement, etc.) were determined. The electrochemical performances of coin cells based on cathodes composed of 85% LiFePO4, 8% of these activated carbons, and 7% polyvinylidene fluoride (PVDF) as a binder, with lithium metal as the anode were studied. Cycling tests and the discharge at different current rates of these cells based on the LiFePO4/C cathodes supported by the various activated carbons were achieved. It was found that the coulombic efficiency, the specific capacity and the discharge at different current densities of these cells were interesting for Li-ion batteries applications. It was shown that their Coulombic efficiency was at least 99% and was very close to that of the cell based on LFP/commercial graphite cathode. The specific capacity of the cells was correlated to the KOH/WH et KOH/MC. Overall, the electrochemical performances of cells based on LFP/MC and LFP/WH were correlated to the physics properties of the activated carbons of MC and WH. Their performances were also compared to those of cells based on LFP/graphite. It was found that cells based on activated carbon obtained from WH exhibited better performances than those from MC. For a given current rate and the same number of cycles, the specific capacity of the cells based on activated carbons of WH is very close to that based on graphite.
- 22 May 2025
- Published by MDPI AG in Preprints.org
Open AccessElectrochemical Performances of Li-Ion Batteries Based on LiFePO4 Cathodes Supported by Bio-Sourced Activated Carbon from Millet Cob (MC) or Water Hyacinth (WH)
The electrochemical performances of Li-ion batteries based on LiFePO4(LFP) cathode supported by bio sourced activated carbon obtained from Millet Cob (MC) or Water Hyacinth (WH) were determined. The carbons were obtained by combustion prior to drying the raw materials of WH and MC, followed by steps of various chemical cleanings, were activated at the following different mass ratios of potassium hydroxide (KOH) and WH or MC respectively: KOH/WH 1:1, 2:1, and 5:1, and KOH/MC 1:1, 2:1, and 5:1.The physics properties (X-ray diffraction patterns, BET surface area, micropore and mesopore volume, conductivity, etc. ) and electrochemical performances (specific capacity, discharge at various current rates, electrochemical impedance measurement, etc.) were determined. The electrochemical performances of coin cells based on cathodes composed of 85% LiFePO4, 8% of these activated carbons, and 7% polyvinylidene fluoride (PVDF) as a binder, with lithium metal as the anode were studied. Cycling tests and the discharge at different current rates of these cells based on the LiFePO4/C cathodes supported by the various activated carbons were achieved. It was found that the coulombic efficiency, the specific capacity and the discharge at different current densities of these cells were interesting for Li-ion batteries applications. It was shown that their Coulombic efficiency was at least 99% and was very close to that of the cell based on LFP/commercial graphite cathode. The specific capacity of the cells was correlated to the KOH/WH et KOH/MC. Overall, the electrochemical performances of cells based on LFP/MC and LFP/WH were correlated to the physics properties of the activated carbons of MC and WH. Their performances were also compared to those of cells based on LFP/graphite. It was found that cells based on activated carbon obtained from WH exhibited better performances than those from MC. For a given current rate and the same number of cycles, the specific capacity of the cells based on activated carbons of WH is very close to that based on graphite.
- Open Access
- 15 October 2024
- Published by Springer Nature in Discover Energy
- Vol. 4 (1) , 1-29
Techno economic analysis of electrolytic hydrogen production by alkaline and PEM electrolysers using MCDM methods
- 15 October 2024
- Published by Springer Nature in Discover Energy
- Vol. 4 (1) , 1-29
Open AccessTechno economic analysis of electrolytic hydrogen production by alkaline and PEM electrolysers using MCDM methods
- 13 June 2023
- Published by ASME International in Journal of Electrochemical Energy Conversion and Storage
- Vol. 21 (1) , 1-16
Exhaust Gas Composition of Lignin Reactions in Molten Carbonate Salt of Direct Carbon Fuel Cell Using FactSage
The most studied Molten Carbonate-Direct Carbon Fuel Cel (MC-LFC) or Molten Carbonate Direct Carbon Fuel Cell (MC-DCFC) prototypes are those which are fed by fossil fuel. Substituting these fossilized fuels in the MC-DCFC operation with lignin, which is a bio-based carbon, may make this system more efficient, clean, and sustainable. The manipulation module (Mixture) and the computational module (Equilib) of the Factsage package were used to simulate two systems that can represent the anodic compartment of a direct carbon fuel cell based on MC-DCFC. The first system includes lignin and a mixture of molten carbonate (Li2CO3-Na2CO3-Cs2CO3). The second system uses the same first electrolyte system but with the addition of CO2 gas. The results show the formation of mixed gases in the anodic compartment which are composed of H2, CO, CO2, CH4 and H2O. The relative concentration of each of the species of this mixed gas has an impact on the efficiency of the MC-DCFC. How the relative concentration of these gases in this electrolyte can impact the performance parameters of the MC-DCFC is systematically analysed. If the operating conditions of the fuel cell are optimized to get a gas composition of mainly of CO2 with low amounts of H2, CO, CH4, H2O in the anode compartment of the MC-DCFC, This will help to improve the conversion efficiency of lignin fuel in the MC-DCFC.
- 13 June 2023
- Published by ASME International in Journal of Electrochemical Energy Conversion and Storage
- Vol. 21 (1) , 1-16
Exhaust Gas Composition of Lignin Reactions in Molten Carbonate Salt of Direct Carbon Fuel Cell Using FactSage
The most studied Molten Carbonate-Direct Carbon Fuel Cel (MC-LFC) or Molten Carbonate Direct Carbon Fuel Cell (MC-DCFC) prototypes are those which are fed by fossil fuel. Substituting these fossilized fuels in the MC-DCFC operation with lignin, which is a bio-based carbon, may make this system more efficient, clean, and sustainable. The manipulation module (Mixture) and the computational module (Equilib) of the Factsage package were used to simulate two systems that can represent the anodic compartment of a direct carbon fuel cell based on MC-DCFC. The first system includes lignin and a mixture of molten carbonate (Li2CO3-Na2CO3-Cs2CO3). The second system uses the same first electrolyte system but with the addition of CO2 gas. The results show the formation of mixed gases in the anodic compartment which are composed of H2, CO, CO2, CH4 and H2O. The relative concentration of each of the species of this mixed gas has an impact on the efficiency of the MC-DCFC. How the relative concentration of these gases in this electrolyte can impact the performance parameters of the MC-DCFC is systematically analysed. If the operating conditions of the fuel cell are optimized to get a gas composition of mainly of CO2 with low amounts of H2, CO, CH4, H2O in the anode compartment of the MC-DCFC, This will help to improve the conversion efficiency of lignin fuel in the MC-DCFC.
- 1 October 2020
- Published by Journal of New Materials for Electrochemical Systems in Journal of New Materials for Electrochemical Systems
- Vol. 23 (4) , 221-224
Will the Future of Electric Vehicles be Powered by Accumulators or Fuel Cells?
- 1 October 2020
- Published by Journal of New Materials for Electrochemical Systems in Journal of New Materials for Electrochemical Systems
- Vol. 23 (4) , 221-224
Will the Future of Electric Vehicles be Powered by Accumulators or Fuel Cells?
- 30 December 2019
- Published by Journal of New Materials for Electrochemical Systems in Journal of New Materials for Electrochemical Systems
- Vol. 22 (4) , 200-216
Development of a New Building Integrated PV-Thermal Solar Module
- 30 December 2019
- Published by Journal of New Materials for Electrochemical Systems in Journal of New Materials for Electrochemical Systems
- Vol. 22 (4) , 200-216
Development of a New Building Integrated PV-Thermal Solar Module