TMTomoshi Miyamura

Tomoshi Miyamura

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Tomoshi Miyamura has a total of 72 co-authors. Here are the top co-authors by number of shared publications:

  • Shinobu Yoshimura

    Univ Tokyo, Sch Engn, Dept Syst Innovat, 7-3-1 Hongo,Bunkyo Ku, Tokyo 1138656, Japan

    9 shared publications
  • Makoto Ohsaki

    Kyoto University

    8 shared publications
  • Takuzo Yamashita

    National Research Institute for Earth Science and Disaster Resilience (NIED), Miki, Hyogo, Japan

    7 shared publications
  • Hirohisa Noguchi

    Department of System Design Engineering, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama 223-8522, Japan

    6 shared publications
  • Makoto Ohsaki

    Department of Architecture and Architectural Engineering, Kyoto University, Kyoto, Japan

    6 shared publications
  • Muneo Hori

    Earthquake Research Institute, The University of Tokyo, 1-1-1 Yayoi, Bunkyo-ku, Tokyo 113-0032, Japan

    5 shared publications

Latest Publications

  • Open Access

    Implicit finite element analysis of ductile fracture of a steel frame under cyclic deformation

    by Makoto Ohsaki, Jun Fujiwara, Tomoshi Miyamura, Hisashi Namba


  • Coupled structural and heat conduction FE analysis of laminated high damping rubber bearing

    by Tomoshi Miyamura, Makoto Ohsaki, Jun Fujiwara, Masashi Yamamoto

    A framework for coupled structural and heat conduction finite element analysis is developed for laminated high damping rubber bearings (HDRBs), and coupled analyses are conducted for full‐scale tests of an HDRB using the shaking table at E‐Defense. An HDRB, which is used in base‐isolated buildings, is modeled using hexahedral solid elements. The high damping rubber is modeled as an overlaid viscohyperelastic and elastic‐plastic constitutive model. However, material parameters are identified using the results for the HDRB subjected to one‐directional loading, and temperature dependences of the parameters are taken into account by a simple method based on empirical formulae for the HDRB because no cyclic coupon test was conducted for the high damping rubber used in the full‐scale tests. The combined structural and heat conduction analyses are conducted for a number of loading cases. The same hexahedral mesh of the HDRB is used for both structural and heat conduction analyses. Analysis results are presented for a one‐directional cyclic loading test, two‐directional loading test with elliptical orbit, and earthquake loading test. The results obtained by the tests and those obtained by the coupled structural and heat conduction analyses are compared. The coupling effect of the mechanical and thermal behaviors is clearly shown in the analysis results, although reductions of the equivalent stiffness and damping are not large because the number of loading cycles in the present analyses is limited.


  • A Comprehensive Numerical Simulation of Steel-Concrete Composite Beam Incorporating Compressive Failure of Concrete

    by Mahendra Kumar Pal, Takuzo Yamashita, Tomoshi Miyamura, Makoto Ohsaki

    We present a high fidelity numerical simulation technique to analyze the nonlinear behavior of a composite beam under cyclic loading. The analysis is performed by using the in-house software called E-Simulator. A constitutive model for concrete; extended Drucker–Prager model considering the compressive failure and the tensile crack has been employed and the parameters are identified so that compressive and tensile behavior of concrete can be reproduced. The relation between the bending moment and deflection angle of a composite beam has been analyzed and compared with experimental results. Damage propagation and stiffness degradation results of concrete slab are demonstrated.


  • Development of a framework to combine an elastic-plastic constitutive model and a creep constitutive model

    by Tomoshi Miyamura, Yasunori Yusa, Jun Yin, Kuniaki Koike, Takashi Ikeda, Tomonori Yamada

    The formulation of a general combined elastic-plastic and creep constitutive model is derived. A partitioned stress integration technique is proposed for the combined model. A simple implementation can be achieved by using the proposed technique. Various kinds of constitutive models such as Ohno-Wang model and Norton-Bailey model can be combined using the present formulation. Therefore, a general framework can be developed to implement material models for a structure used in a high temperature environment.

  • Feasibility study of full-scale elastic-plastic seismic response analysis of nuclear power plant

    by Tomoshi Miyamura, Shinobu Yoshimura, Tomonori Yamada

    A finite element elastic-plastic seismic response analysis using a full-scale integrated model of Unit 1 of the Fukushima-Daiichi Nuclear Power Plant, which was subjected to the 2011 off the Pacific coast of Tohoku Earthquake, is performed using the K computer in order to obtain both the global and local responses more precisely. The purpose of the present study is to investigate the computational performance and show the feasibility of such an analysis. The high-fidelity finite element mesh for the plant used in the present study was generated using tetrahedral elements in a previous study by Yoshimura et al. (2019a) for the pressure vessel, the containment vessel, the suppression chamber, the vent pipes, a number of supports, and the reactor building. The mesh with linear elements has approximately 200 million DOFs. The elastoplasticity is taken into account for only the steel used in the pressure and containment vessels. However, the material for the reactor building is assumed to be elastic. The dynamic response during 55 s is solved successfully, although yielding occurs at very few points. The total elapsed time for analysis is approximately 14.2 days using 1,032 nodes of the K computer. If the nonlinearity increases, the computation time may be increased by three to four times due to the increase in the number of Newton-Raphson iteration steps. Even in this case, the computation time can be estimated to be less than two months, which means that an elastic-plastic seismic response analysis of the plant using the high-fidelity finite element mesh is feasible. An elastic-plastic seismic response analysis using a quadratic element model with approximately 1.5 billion DOFs is also successfully conducted for 12 time steps (0.12 s) using 4,128 nodes of the K computer.


  • Open Access

    Seismic Response Analysis of Unit 1 of Fukushima-Daiichi Nuclear Power Plant During the 2011 Off the Pacific Coast of Tohoku Earthquake Using Three-Dimensional Finite Element Method (1st Report: Development of Analysis Method, Model Construction and Verification of Analysis Performance)

    by Shinobu Yoshimura, Tomoshi Miyamura, Tomonori Yamada, Hiroshi Akiba, Hideaki Kiyoura

    This research presents the recent development of the analysis system ADVENTURE, i.e., a parallel structural analysis solver ADVENTURE_Solid Ver.2 and its pre-/post-modules, towards petascale computers such as the K computer with 10 petaflops peak performance, as well as its application to three-dimensional finite element seismic response analyses of a full-scale integrated model of the boiling water reactor and reactor building of Unit 1 at the Fukushima-Daiichi Nuclear Power Plant subjected to the 2011 off the Pacific coast of Tohoku Earthquake of 9.0 Mw occurring on March 11, 2011. Here, we precisely modeled its pressure vessel, containment vessel, suppression chamber, vent piping, a number of supports and the reactor building with a 200 million DOF finite element mesh. Then, we successfully solved its dynamic response in 65 s. We report our research results in two papers, i.e., Part I and Part II. Part I (this paper) reports the developed analysis method, model construction, verification of the analysis model, and computation performance. Part II reports the results of an eigenanalysis and a seismic response analysis. Finally, we concluded some key roles of petascale simulation for such practical and socially important problems.


  • FINITE ELEMENT ANALYSIS OF SQUARE CONCRETE-FILLED-TUBE COLUMN UNDER CYCLIC SHEAR-BENDING CONSIDERING COMPRESSIVE DAMAGE OF CONCRETE

    by Jun Fujiwara, Makoto Ohsaki, Hiroyuki Tagawa, Tomoshi Miyamura, Takuzo Yamashita

    In this paper, we conduct a finite element analysis of a square concrete-filled-tube (CFT) column to replicate cyclic shear-bending behavior under constant axial load. CFTs are used as columns of architectural and civil engineering structures. CFTs usually have large deformation capacity due to lateral constraints from steel tubes providing ductility. There are several existing studies on numerical analysis of CFTs. To the best of authors' knowledge, however, no numerical analysis method for simulating cyclic bending behavior of CFTs, in which interaction between steel tube and filled concrete, softening of concrete and local buckling of steel tube are simultaneously considered, has been proposed. The authors have been developing a detailed finite element analysis system called E-Simulator. In this research project, we simulate structural behavior only by combining detailed solid finite element model and material constitutive laws, which can represent damages and fractures of materials. By using E-Simulator, we can consider interaction between filled concrete and steel tube without any additional constraint effects. The concrete constitutive model, which has been proposed by the authors, is updated and applied to the analysis. The concrete model is a combination of extended Drucker-Prager model and a simple damage criterion. Here, we improve the concrete constitutive model so that damage progresses only in compressive stress state. A cyclic shear-bending loading experiment of a square CFT column is replicated. The height and width of the column are 1440 mm and 240 mm, respectively. A pseudo-static cyclic lateral displacement and a constant vertical load are given at the top of the column. The ratio of lateral displacement amplitude to the column height is increased from 1/400 to 1/33, gradually. The CFT consists of high strength concrete and steel, whose nominal strengths are 150 N/mm2 and 780 N/mm2, respectively. The material parameters are identified from material tests. The load-deformation relation obtained from the numerical result is compared to the experimental one. The interaction between the filled concrete and the steel tube is also discussed. The results of the analysis are summarized as follows: 1. The load-displacement relationships of the analysis and experiment have been almost linear and elastic until the distortion angle has reached 1/100. The stiffness of the analysis has agreed well to that of the experiment. The load measured in the experiment is not proportional to the displacement. In positive loading direction, as a result, the load of the analysis is larger than the experimental one. The ratio of load from the analysis to the experimental one is 0.979 – 1.142 in positive loading direction, 0.715 - 1.004 in negative loading direction. 2. When the distortion angle has exceeded 1/100 first, strength deterioration due to local buckling of the tube and damage of the concrete has been seen in the numerical result. In the experiment, local buckling of the steel tube has been observed in the same loading cycle. Although the strength deterioration in the analysis has occurred later than that in the experiment, the load-deformation relation of the experiment after plasticizing has been replicated, qualitatively. The ratio of load from the analysis to the experimental one is 1.076 – 1.154. 3. The contact between the filled concrete and the steel tube due to the local buckling of steel tube has been first observed. After that, the large bending deformation has caused another contact. The contact pressure gave the concrete confinement, which made the equivalent stress higher than the uniaxial compressive strength of the damaged concrete. From this result, it can be concluded that interaction between filled concrete and steel tube can be represented by using detailed solid FE mesh model and E-Simulator.