JEJames P. Evans

James P. Evans

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


James P. Evans has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Composition, microstructures, and petrophysics of the Mozumi fault, Japan: In situ analyses of fault zone properties and structure in sedimentary rocks from shallow crustal levels

    by Angela J. Isaacs, James P. Evans, Peter T. Kolesar, Tsuyoshi Nohara

    We characterize the chemical, microstructural, and geophysical properties of fault‐related rock samples from the 80–100 m wide Mozumi fault zone, north central Honshu, Japan. The fault is exposed in a research tunnel 300–400 m below the ground, and we combine geological data with borehole geophysical logs to determine the elastic and seismic properties of the fault zone. Detailed mapping within the tunnel reveals that the fault zone consists of two zones of breccia to foliated cataclasites 20 and 50 m thick. Two narrow (tens of centimeters wide) principal slip zones on which most of the slip occurred bound the central fault zone. The dominant deformation mechanisms within the fault zone were brittle fracture, brecciation, slip localization, plastic deformation, and vein formation in a sericite‐calcite rich matrix. Clay alteration patterns are complex within the fault zone, with clay‐rich fault breccia enriched in smectite, illite, and kaolinite relative to the kaolinite and illite dominant in the host rock. Whole rock geochemical analyses show that the fault‐related rocks are depleted in Fe, Na, K, Al, Mg, and Si relative to the host rock. The fault zone exhibits depressed electrical resistivity values by 10–100 ohm m relative to the wall rock, values of Vp and Vs values that are ∼0.30 and ∼0.40 km/s (10–20%) less than protolith values. The spontaneous potential logs indicate that the fault zone has increased freshwater content relative to formation waters. Wellbore‐based measurements of Vp and Vs in fault‐related rocks to enable us to calculate values of Young's modulus from 16.2 to 44.9 GPa and Poisson's ratio for the fault zone of 0.263 to 0.393. The protolith has Young's modulus of 55.4 GPa and a Poisson's ratio of 0.242. Lowest calculated values of Young's modulus and highest calculated values of Poisson's ratio correspond to fault breccia with increased porosity, high fluid content, and low resistivity values. Taken together, these data show that the shallow portion of the Mozumi fault consists of a complex zone of anastomosing narrow slip zones that bound broad zones of damage. Fluid‐rock alteration and deformation created altered fault‐related rocks, which have resulted in overall reduced interval velocities of the fault zone. These data indicate that seismic waves traveling along the interface or internally reflected in the fault zone would encounter rocks of differing and reduced elastic properties relative to the host rocks but that in detail, material properties within the fault may vary.


  • Geochemistry of CO2 sequestration in the Jurassic Navajo Sandstone, Colorado Plateau, Utah

    by W. T. Parry, Craig B. Forster, J. P. Evans, Brenda Beitler Bowen, Marjorie A. Chan

    The Jurassic Navajo Sandstone on the Colorado Plateau of Utah may be considered for sequestration of CO2, because it is thick, widely distributed, has a high porosity and permeability, is typically horizontal to gently folded, is favorably located with respect to seal strata, and underlies many large point sources of CO2. However, faulting common on the Colorado Plateau may provide pathways for leakage of the CO2 similar to present-day geysers and CO2-charged springs. Natural groundwater present in the Navajo Sandstone includes a range of low-salinity, moderate-salinity with high bicarbonate, and high-salinity waters. Higher salinity waters may have moved from deeper strata under artesian pressures or originated from solution of evaporite in pre-Jurassic rocks. These characteristics make the Navajo Sandstone an excellent analog for examining the geochemistry of CO2 injection into deep saline aquifers. The storativity of CO2 in solution is a function of the solubility of CO2 in these waters, which is dependent on salinity, temperature, and pressure. Geochemical modeling shows that the coolest, least saline water can contain the most CO2 in solution. Dissolving CO2 in the water lowers the pH, so that no minerals precipitate, and the Navajo Sandstone contains only small amounts of mineral that may consume the H+. The reaction of the acidic water produced by dissolving CO2 with K-feldspar and minor clays and calcite in the sandstone throughout 500 yr consumes little H+ and produces only small amounts of product minerals. The Navajo Sandstone likely would not store significant CO2 as mineral precipitate, and thus, stored volumes of CO2 would be limited by its solubility in the in-situ water and storage as free CO2 in pore space.


  • Faulting and Fracturing of Nonwelded Bishop Tuff, Eastern California: Deformation Mechanisms in Very Porous Materials in the Vadose Zone

    by James P. Evans, Kelly Keighley Bradbury

    Field and microstructural studies were conducted on the basal, nonwelded and partially welded portions of the rhyolite Bishop Tuff in eastern California to examine the nature and processes of brittle deformation in these units. The nonwelded tuff consists of a variable sequence of finely laminated to massive pumice‐rich deposits, fine‐grained ash, and pyroclastic glass erupted from the Long Valley Caldera. The deposits are experiencing east–west extension in the hanging wall of the White Mountain fault, and small‐displacement faults and fractures cut the tuff. Deformation in the Bishop Tuff occurred by fracturing associated with faults, and by slip along narrow faults with smooth, often mineralized surfaces. Localization of fracturing appears to be a function of welding. Units with a greater degree of welding have a greater abundance of fractures associated with faults, whereas nonwelded portions typically have a narrow deformation band–type faults with little or no associated damage. Microstructural observations show that transgranular fractures lie along grain boundaries of pumice and feldspar phenocrysts, and these fractures are often filled with calcite. These deposits appear to have behaved as an open‐cell foam with a low strength, but with a cohesion that allowed the support of a differential stress to failure that resulted in subvertical open fractures and faults. These results demonstrate how brittle deformation may be manifested in nonwelded deposits in the vadose zone, and impart an anisotropy in which flow would be enhanced vertically and impeded horizontally. The Bishop Tuff is analogous to other nonwelded tuffs in the western USA. Thus, these results have implications for understanding deformation and flow in a variety of arid regions.


  • Structural Heterogeneity and Permeability in Faulted Eolian Sandstone: Implications for Subsurface Modeling of Faults

    by Zoe K. Shipton, James P. Evans, Kim R. Robeson, Craig B. Forster, Stephen Snelgrove

    We determined the structure and permeability variations of a 4 km-long normal fault by integrating surface mapping with data from five boreholes drilled through the fault (borehole to tens of meters scale). The Big Hole fault outcrops in the Jurassic Navajo Sandstone, central Utah. A total of 363.2 m of oriented drill core was recovered at two sites where fault displacement is 8 and 3-5 m. The main fault core is a narrow zone of intensely comminuted grains that is a maximum of 30 cm thick and is composed of low-porosity amalgamated deformation bands that have slip surfaces on one or both sides. Probe permeameter measurements showed a permeability decline from greater than 2000 to less than 0.1 md as the fault is approached. Whole-core analyses showed that fault core permeability is less than 1 md and individual deformation band permeability is about 1 md. Using these data, we calculated the bulk permeability of the fault zone. Calculated transverse permeability over length scales of 5-10 m is 30-40 md, approximately 1-4% the value of the host rock. An inverse power mean calculation (representing a fault array with complex geometry) yielded total fault-zone permeabilities of 7-57 md. The bulk fault-zone permeability is most sensitive to variations in fault core thickness, which exhibits the greatest variability of the fault components.


  • Fault zone architecture and permeability structure

    by Jonathan Saul Caine, James P. Evans, Craig B. Forster

    Fault zone architecture and related permeability structures form primary controls on fluid flow in upper-crustal, brittle fault zones. We develop qualitative and quantitative schemes for evaluating fault-related permeability structures by using results of field investigations, laboratory permeability measurements, and numerical models of flow within and near fault zones. The qualitative scheme compares the percentage of the total fault zone width composed of fault core materials (e.g., anastomosing slip surfaces, clay-rich gouge, cataclasite, and fault breccias) to the percentage of subsidiary damage zone structures (e.g., kinematically related fracture sets, small faults, and veins). A more quantitative scheme is developed to define a set of indices that characterize fault zone architecture and spatial variability. The fault core and damage zone are distinct structural and hydrogeologic units that reflect the material properties and deformation conditions within a fault zone. Whether a fault zone will act as a conduit, barrier, or combined conduit-barrier system is controlled by the relative percentage of fault core and damage zone structures and the inherent variability in grain scale and fracture permeability. This paper outlines a framework for understanding, comparing, and correlating the fluid flow properties of fault zones in various geologic settings.