Craig B. Forster
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Craig B. Forster has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Ari Menitove
University of Utah, 423 Wakara Way, Salt Lake City, Utah, 84108
1 shared publicationDeming Wang
University of Texas at Dallas, 2601 N. Floyd Road, Richardson, Texas, 75080
1 shared publication- George A. McMechan
The University of Texas at Dallas 2 , Center for Lithospheric Studies, 800 West Campbell Road (ROC21), Richardson, Texas 75080, USA.
1 shared publication - James P. Evans
Department of Geology, Utah State University, Logan, Utah 84322-4505
1 shared publication John B. Thurmond
Massachusetts Institute of Technology, 77 Massachusetts Avenue, 54-913, Cambridge, Massachusetts, 02139
1 shared publicationKim R. Robeson
Deceased
1 shared publication
Latest Publications
- 1 May 2002
- Published by American Association of Petroleum Geologists AAPG/Datapages in AAPG Bulletin
- Vol. 86 (5) , 863-883
Structural Heterogeneity and Permeability in Faulted Eolian Sandstone: Implications for Subsurface Modeling of Faults
We determined the structure and permeability variations of a 4 km-long normal fault by integrating surface mapping with data from five boreholes drilled through the fault (borehole to tens of meters scale). The Big Hole fault outcrops in the Jurassic Navajo Sandstone, central Utah. A total of 363.2 m of oriented drill core was recovered at two sites where fault displacement is 8 and 3-5 m. The main fault core is a narrow zone of intensely comminuted grains that is a maximum of 30 cm thick and is composed of low-porosity amalgamated deformation bands that have slip surfaces on one or both sides. Probe permeameter measurements showed a permeability decline from greater than 2000 to less than 0.1 md as the fault is approached. Whole-core analyses showed that fault core permeability is less than 1 md and individual deformation band permeability is about 1 md. Using these data, we calculated the bulk permeability of the fault zone. Calculated transverse permeability over length scales of 5-10 m is 30-40 md, approximately 1-4% the value of the host rock. An inverse power mean calculation (representing a fault array with complex geometry) yielded total fault-zone permeabilities of 7-57 md. The bulk fault-zone permeability is most sensitive to variations in fault core thickness, which exhibits the greatest variability of the fault components.
- 1 May 2002
- Published by American Association of Petroleum Geologists AAPG/Datapages in AAPG Bulletin
- Vol. 86 (5) , 863-883
Structural Heterogeneity and Permeability in Faulted Eolian Sandstone: Implications for Subsurface Modeling of Faults
We determined the structure and permeability variations of a 4 km-long normal fault by integrating surface mapping with data from five boreholes drilled through the fault (borehole to tens of meters scale). The Big Hole fault outcrops in the Jurassic Navajo Sandstone, central Utah. A total of 363.2 m of oriented drill core was recovered at two sites where fault displacement is 8 and 3-5 m. The main fault core is a narrow zone of intensely comminuted grains that is a maximum of 30 cm thick and is composed of low-porosity amalgamated deformation bands that have slip surfaces on one or both sides. Probe permeameter measurements showed a permeability decline from greater than 2000 to less than 0.1 md as the fault is approached. Whole-core analyses showed that fault core permeability is less than 1 md and individual deformation band permeability is about 1 md. Using these data, we calculated the bulk permeability of the fault zone. Calculated transverse permeability over length scales of 5-10 m is 30-40 md, approximately 1-4% the value of the host rock. An inverse power mean calculation (representing a fault array with complex geometry) yielded total fault-zone permeabilities of 7-57 md. The bulk fault-zone permeability is most sensitive to variations in fault core thickness, which exhibits the greatest variability of the fault components.
- 1 September 2001
- Published by American Association of Petroleum Geologists AAPG/Datapages in AAPG Bulletin
- Vol. 85 (9) , 1583-1608
Detailed Internal Architecture of a Fluvial Channel Sandstone Determined from Outcrop, Cores, and 3-D Ground-Penetrating Radar: Example from the Middle Cretaceous Ferron Sandstone, East-Central Utah
Ideally, characterization of hydrocarbon reservoirs requires information about heterogeneity at a submeter scale in three dimensions. Detailed geologic information and permeability data from surface and cliff face outcrops and boreholes in the alluvial part of the Ferron Sandstone are integrated here with three-dimensional (3-D) ground-penetrating radar (GPR) data for analysis of a near-surface sandstone reservoir analog in fluvial channel deposits. The GPR survey covers a volume with a surface area of 40 x 16.5 m and a depth of 12 m. Five architectural elements are identified and described in outcrop and well cores, using a sixfold hierarchy of bounding surfaces. Internally, the lower four units consist of fine-grained, parallel-laminated sandstone, and the upper unit consists of medium-grained, trough cross-bedded sandstone. The same sedimentary architectural elements and associated bounding surfaces are distinguished in the GPR data by making use of principles developed in seismic stratigraphic analysis. To facilitate comparison of geologic features in the depth domain and radar reflectors in the time domain, the radar data are depth migrated. The GPR interpretation is carried out mainly on migrated 100 MHz data with a vertical resolution of about 0.5 m. Measures of the spatial continuity and variation of the first- and second-order bounding surfaces are obtained by computing 3-D experimental variograms for each architectural element (each radar facies). The maximum correlation length of the dominant internal features ranges between 4 and 6 m, and the anisotropy factor ranges between 0.6 and 0.95.
- 1 September 2001
- Published by American Association of Petroleum Geologists AAPG/Datapages in AAPG Bulletin
- Vol. 85 (9) , 1583-1608
Detailed Internal Architecture of a Fluvial Channel Sandstone Determined from Outcrop, Cores, and 3-D Ground-Penetrating Radar: Example from the Middle Cretaceous Ferron Sandstone, East-Central Utah
Ideally, characterization of hydrocarbon reservoirs requires information about heterogeneity at a submeter scale in three dimensions. Detailed geologic information and permeability data from surface and cliff face outcrops and boreholes in the alluvial part of the Ferron Sandstone are integrated here with three-dimensional (3-D) ground-penetrating radar (GPR) data for analysis of a near-surface sandstone reservoir analog in fluvial channel deposits. The GPR survey covers a volume with a surface area of 40 x 16.5 m and a depth of 12 m. Five architectural elements are identified and described in outcrop and well cores, using a sixfold hierarchy of bounding surfaces. Internally, the lower four units consist of fine-grained, parallel-laminated sandstone, and the upper unit consists of medium-grained, trough cross-bedded sandstone. The same sedimentary architectural elements and associated bounding surfaces are distinguished in the GPR data by making use of principles developed in seismic stratigraphic analysis. To facilitate comparison of geologic features in the depth domain and radar reflectors in the time domain, the radar data are depth migrated. The GPR interpretation is carried out mainly on migrated 100 MHz data with a vertical resolution of about 0.5 m. Measures of the spatial continuity and variation of the first- and second-order bounding surfaces are obtained by computing 3-D experimental variograms for each architectural element (each radar facies). The maximum correlation length of the dominant internal features ranges between 4 and 6 m, and the anisotropy factor ranges between 0.6 and 0.95.