Mehmet Yasar Gundogdu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Mehmet Yasar Gundogdu has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Ihsan Kutlar
University of Gaziantep
2 shared publications - Fuat Yilmaz
Department of Mechanical Engineering, Gaziantep University, Gaziantep, Turkey
1 shared publication Melda O. Carpinlioglu
Mechanical Engineering Department, Faculty of Engineering , University of Gaziantep , Gaziantep, Turkey
1 shared publication
Latest Publications
- 1 June 2011
- Published by Springer Nature in Korea-Australia Rheology Journal
- Vol. 23 (2) , 89-103
Analysis of drag effects on pulsatile blood flow in a right coronary artery by using Eulerian multiphase model
- 1 June 2011
- Published by Springer Nature in Korea-Australia Rheology Journal
- Vol. 23 (2) , 89-103
Analysis of drag effects on pulsatile blood flow in a right coronary artery by using Eulerian multiphase model
- 21 November 2008
- Published by Taylor & Francis in Particulate Science and Technology
- Vol. 26 (6) , 551-562
Discharge Regimes of Polydisperse Powders through Conical Hoppers under Positive Flow Conditions
Discharge characteristics of polydisperse powders through a conical hopper were experimentally investigated by observing the solids discharge regimes under different positive pressure differences (i.e., ΔP > 0) and also measuring the corresponding solids discharge rates. The observations and measurements were systematically conducted at least four diameters of hopper orifice (2.5 mm ≤ Do ≤ 30.0 mm) under five positive ΔP values (0 Pa ≤ ΔP ≤ 1405 Pa) for the test powders: river sand, zeolite, fertilizer, and sawdust. Effects of positive ΔP on both discharge regime and solids discharge rate are first predicted for different orifice diameters and test powders in this study. One of the novel results on the discharge regime is that increase of positive ΔP value up to a critical value conserves or successively stabilizes the discharge regime observed when ΔP = 0 (i.e., for gravity flow condition) through the same hopper. However, the additional increase of positive ΔP over this critical value destabilizes the discharge regime, as in conformity with the effect of increase in negative ΔP cited in the literature.
- 21 November 2008
- Published by Taylor & Francis in Particulate Science and Technology
- Vol. 26 (6) , 551-562
Discharge Regimes of Polydisperse Powders through Conical Hoppers under Positive Flow Conditions
Discharge characteristics of polydisperse powders through a conical hopper were experimentally investigated by observing the solids discharge regimes under different positive pressure differences (i.e., ΔP > 0) and also measuring the corresponding solids discharge rates. The observations and measurements were systematically conducted at least four diameters of hopper orifice (2.5 mm ≤ Do ≤ 30.0 mm) under five positive ΔP values (0 Pa ≤ ΔP ≤ 1405 Pa) for the test powders: river sand, zeolite, fertilizer, and sawdust. Effects of positive ΔP on both discharge regime and solids discharge rate are first predicted for different orifice diameters and test powders in this study. One of the novel results on the discharge regime is that increase of positive ΔP value up to a critical value conserves or successively stabilizes the discharge regime observed when ΔP = 0 (i.e., for gravity flow condition) through the same hopper. However, the additional increase of positive ΔP over this critical value destabilizes the discharge regime, as in conformity with the effect of increase in negative ΔP cited in the literature.
- 1 January 2006
- Published by Taylor & Francis in Particulate Science and Technology
- Vol. 24 (1) , 23-37
Discharge Characteristics of Polydisperse Powders through Conical Hoppers. Part 2: Predictions for Coarse, Granular, Free Flowing Powders
Discharge characteristics of coarse polydisperse granular powders through a conical hopper are experimentally investigated. The average discharge rates of four different powder types are systematically measured for seven different diameters of hopper orifice under gravity flow conditions. Each powder type is a mixture of some sub-sizes (smaller than 3 mm) of same powder material. Effects of orifice diameter of hopper and size distribution of polydisperse powders on discharge characteristics are experimentally determined. The measured discharge data are compared with discharge values predicted by using modified forms of the well-known Beverloo correlation. The volume-moment-mean diameter, dVM, and the 50% weight fraction diameter, d50, cited in available literature are both checked to characterize the coarse polydisperse powders and used throughout the predictions. Comparisons implied that both dVM and d50 diameters can be successfully used to characterize polydisperse test powders, and discharge rate predictions are in good agreement with experimental data, with mean deviations lower than ±4.04%.
- 1 January 2006
- Published by Taylor & Francis in Particulate Science and Technology
- Vol. 24 (1) , 23-37
Discharge Characteristics of Polydisperse Powders through Conical Hoppers. Part 2: Predictions for Coarse, Granular, Free Flowing Powders
Discharge characteristics of coarse polydisperse granular powders through a conical hopper are experimentally investigated. The average discharge rates of four different powder types are systematically measured for seven different diameters of hopper orifice under gravity flow conditions. Each powder type is a mixture of some sub-sizes (smaller than 3 mm) of same powder material. Effects of orifice diameter of hopper and size distribution of polydisperse powders on discharge characteristics are experimentally determined. The measured discharge data are compared with discharge values predicted by using modified forms of the well-known Beverloo correlation. The volume-moment-mean diameter, dVM, and the 50% weight fraction diameter, d50, cited in available literature are both checked to characterize the coarse polydisperse powders and used throughout the predictions. Comparisons implied that both dVM and d50 diameters can be successfully used to characterize polydisperse test powders, and discharge rate predictions are in good agreement with experimental data, with mean deviations lower than ±4.04%.