Vicente Gómez-Serrano
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vicente Gómez-Serrano has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- María Alexandre-Franco
Departamento de Química Orgánica e Inorgánica, Facultad de Ciencias, Universidad de Extremadura, Avenida de Elvas s/n, 06006 Badajoz, Spain
12 shared publications - Carmen Fernandez Gonzalez
Departamento de Química Orgánica e Inorgánica, Facultad de Ciencias, Universidad de Extremadura, Avenida de Elvas s/n, 06006 Badajoz, Spain
11 shared publications - Adrián Barroso-Bogeat
GIR QUESCAT, Departamento de Química Inorgánica, Universidad de Salamanca, 37008 Salamanca, Spain
4 shared publications - Antonio Macías García
University of Extremadura
4 shared publications - Eduardo Manuel Cuerda Correa
Departamento de Química Orgánica e Inorgánica, Facultad de Ciencias, Universidad de Extremadura, Avenida de Elvas s/n, 06006 Badajoz, Spain
3 shared publications - Jose Miguel Gonzalez-Dominguez
Instituto de Carboquimica ICB-CSIC, C/Miguel Luesma Castan 4, 50018 Zaragoza, Spain
3 shared publications
Latest Publications
- Open Access
Upcycling Used Tyre Rubber into Carbon Adsorbents: Effect of Physical Activation on Porous Structure and Comparative Evaluation for p-Chlorophenol Removal
The porous architecture of carbons derived from polymeric waste is largely governed by the physical activation atmosphere. In this work, used tyre rubber (UTR) was converted into carbonaceous adsorbents by pyrolysis followed by physical activation in air, CO2 or steam. The influence of the activation route on porous structure, surface chemistry and adsorption performance was systematically investigated. The materials were characterised by N2 adsorption at −196 °C, mercury intrusion porosimetry, scanning electron microscopy (SEM), FT-IR spectroscopy and point-of-zero-charge (pHpzc) measurements. The resulting materials were evaluated for the removal of p-chlorophenol from aqueous solution and comparatively assessed against three commercial carbon materials. Steam activation proved to be the most effective treatment, increasing the BET surface area from 64 to 344 m2 g−1 and the micropore volume from 0.05 to 0.23 cm3 g−1 while generating a hierarchical micro-/mesoporous structure that significantly enhanced pore accessibility and mass transport. Among the UTR-derived carbons, the steam-activated sample exhibited the highest equilibrium p-Cp uptake and adsorption kinetics approaching those of a commercial activated carbon despite its lower specific surface area. Kinetic and equilibrium analyses demonstrated that adsorption performance depends not only on the extent of microporosity but also on pore accessibility and network connectivity, highlighting the critical role of transport mesoporosity in facilitating molecular diffusion towards adsorption sites. The adsorption results are consistent with an important contribution from accessible microporosity, while π–π interactions between p-chlorophenol and aromatic carbon domains may also contribute. These findings demonstrate that tailoring porous structure through physical activation provides an effective strategy for transforming UTR into high-performance carbon adsorbents and establishes robust processing–structure–property relationships that can guide the rational design of waste-derived carbon adsorbents.
Open AccessUpcycling Used Tyre Rubber into Carbon Adsorbents: Effect of Physical Activation on Porous Structure and Comparative Evaluation for p-Chlorophenol Removal
The porous architecture of carbons derived from polymeric waste is largely governed by the physical activation atmosphere. In this work, used tyre rubber (UTR) was converted into carbonaceous adsorbents by pyrolysis followed by physical activation in air, CO2 or steam. The influence of the activation route on porous structure, surface chemistry and adsorption performance was systematically investigated. The materials were characterised by N2 adsorption at −196 °C, mercury intrusion porosimetry, scanning electron microscopy (SEM), FT-IR spectroscopy and point-of-zero-charge (pHpzc) measurements. The resulting materials were evaluated for the removal of p-chlorophenol from aqueous solution and comparatively assessed against three commercial carbon materials. Steam activation proved to be the most effective treatment, increasing the BET surface area from 64 to 344 m2 g−1 and the micropore volume from 0.05 to 0.23 cm3 g−1 while generating a hierarchical micro-/mesoporous structure that significantly enhanced pore accessibility and mass transport. Among the UTR-derived carbons, the steam-activated sample exhibited the highest equilibrium p-Cp uptake and adsorption kinetics approaching those of a commercial activated carbon despite its lower specific surface area. Kinetic and equilibrium analyses demonstrated that adsorption performance depends not only on the extent of microporosity but also on pore accessibility and network connectivity, highlighting the critical role of transport mesoporosity in facilitating molecular diffusion towards adsorption sites. The adsorption results are consistent with an important contribution from accessible microporosity, while π–π interactions between p-chlorophenol and aromatic carbon domains may also contribute. These findings demonstrate that tailoring porous structure through physical activation provides an effective strategy for transforming UTR into high-performance carbon adsorbents and establishes robust processing–structure–property relationships that can guide the rational design of waste-derived carbon adsorbents.
- Top Cited PapersOpen Access
Coconut Shell-Derived Activated Carbons: Preparation, Physicochemical Properties, and Dye Removal from Water
Valorizing coconut shell waste as a renewable lignocellulosic precursor offers a sustainable route to produce high-performance activated carbons for wastewater treatment. In this study, coconut shells were transformed into activated carbons through physical activation (air, CO2, steam) and chemical activation (H3PO4, ZnCl2, KOH), allowing direct comparison of how each method influences porosity and surface chemistry. Among the physically activated samples, steam activation produced the best material, A-ST, with SBET = 738 m2 g−1, Vmi = 0.38 cm3 g−1 and Vme = 0.07 cm3 g−1. KOH activation yielded the top-performing carbon, A-KOH, achieving SBET = 1600 m2 g−1, Vmi = 0.74 cm3 g−1, and Vme = 0.22 cm3 g−1. Adsorption tests with methylene blue, methyl orange, and orange G showed a clear link between physicochemical features and dye uptake. A-ST and A-KOH exhibited the highest capacities due to their wide micro–mesoporosity and favorable surface charge at the adsorption pH. In both cases, methylene blue was most strongly retained, confirming that large aromatic cations benefit from π–π interactions with graphene-like layers and easy micropore access. Overall, the results demonstrate that coconut-shell valorization is maximized when activation enhances both porosity and surface chemistry, enabling the production of tailored sorbents for the efficient removal of organic contaminants.
Top Cited PapersOpen AccessCoconut Shell-Derived Activated Carbons: Preparation, Physicochemical Properties, and Dye Removal from Water
Valorizing coconut shell waste as a renewable lignocellulosic precursor offers a sustainable route to produce high-performance activated carbons for wastewater treatment. In this study, coconut shells were transformed into activated carbons through physical activation (air, CO2, steam) and chemical activation (H3PO4, ZnCl2, KOH), allowing direct comparison of how each method influences porosity and surface chemistry. Among the physically activated samples, steam activation produced the best material, A-ST, with SBET = 738 m2 g−1, Vmi = 0.38 cm3 g−1 and Vme = 0.07 cm3 g−1. KOH activation yielded the top-performing carbon, A-KOH, achieving SBET = 1600 m2 g−1, Vmi = 0.74 cm3 g−1, and Vme = 0.22 cm3 g−1. Adsorption tests with methylene blue, methyl orange, and orange G showed a clear link between physicochemical features and dye uptake. A-ST and A-KOH exhibited the highest capacities due to their wide micro–mesoporosity and favorable surface charge at the adsorption pH. In both cases, methylene blue was most strongly retained, confirming that large aromatic cations benefit from π–π interactions with graphene-like layers and easy micropore access. Overall, the results demonstrate that coconut-shell valorization is maximized when activation enhances both porosity and surface chemistry, enabling the production of tailored sorbents for the efficient removal of organic contaminants.
- Open Access
Support Surface Chemistry Evolution During the Preparation of Metal Oxide–Activated Carbon Catalysts by Wet Impregnation: A FT-IR Spectroscopy Analysis
The present work is aimed at shedding light on the evolution of surface chemistry of a commercial activated carbon (AC) support during the preparation of supported metal oxide (MO) catalysts by the conventional wet impregnation method. Particular attention is paid to the chemical changes of oxygen-containing surface functionalities across three preparation stages of impregnation, oven-drying, and thermal treatment. AC was impregnated with aqueous solutions of several MO precursors (Al(NO3)3, Fe(NO3)3, Zn(NO3)2, SnCl2, and Na2WO4) at 80 °C for 5 h, oven-dried at 120 °C for 24 h, and heat-treated at 200 °C and 850 °C for 2 h under an inert atmosphere. The surface chemistry of the resulting catalyst samples, classified in three series by the thermal treatment, was mainly studied by FT-IR spectroscopy, complemented by elemental analysis and pH of the point of zero charge (pHpzc) measurements. During impregnation, phenolic hydroxyl and carboxylic acid groups were predominantly formed by wet oxidation of chromene, 2-pyrone, and ether-type structures found in the pristine AC. The extent of these oxidations correlated with the oxidising power of the precursor solutions. As expected, thermal treatment at 850 °C brought about markedly stronger chemical changes, with most of the above oxygen functionalities decomposing and forming less acidic structures, such as 4-pyrone groups, metal carboxylates, and C-O-M atomic groupings. All these surface chemical modifications result in a lowering of the strong basicity of the raw carbon support (pHpzc ≈ 10.5), thus leading to pHpzc values for the catalysts widely ranging from 1.6 to 9.7.
Open AccessSupport Surface Chemistry Evolution During the Preparation of Metal Oxide–Activated Carbon Catalysts by Wet Impregnation: A FT-IR Spectroscopy Analysis
The present work is aimed at shedding light on the evolution of surface chemistry of a commercial activated carbon (AC) support during the preparation of supported metal oxide (MO) catalysts by the conventional wet impregnation method. Particular attention is paid to the chemical changes of oxygen-containing surface functionalities across three preparation stages of impregnation, oven-drying, and thermal treatment. AC was impregnated with aqueous solutions of several MO precursors (Al(NO3)3, Fe(NO3)3, Zn(NO3)2, SnCl2, and Na2WO4) at 80 °C for 5 h, oven-dried at 120 °C for 24 h, and heat-treated at 200 °C and 850 °C for 2 h under an inert atmosphere. The surface chemistry of the resulting catalyst samples, classified in three series by the thermal treatment, was mainly studied by FT-IR spectroscopy, complemented by elemental analysis and pH of the point of zero charge (pHpzc) measurements. During impregnation, phenolic hydroxyl and carboxylic acid groups were predominantly formed by wet oxidation of chromene, 2-pyrone, and ether-type structures found in the pristine AC. The extent of these oxidations correlated with the oxidising power of the precursor solutions. As expected, thermal treatment at 850 °C brought about markedly stronger chemical changes, with most of the above oxygen functionalities decomposing and forming less acidic structures, such as 4-pyrone groups, metal carboxylates, and C-O-M atomic groupings. All these surface chemical modifications result in a lowering of the strong basicity of the raw carbon support (pHpzc ≈ 10.5), thus leading to pHpzc values for the catalysts widely ranging from 1.6 to 9.7.
- Open Access
Surface Chemistry of Cherry Stone-Derived Activated Carbon Prepared by H3PO4 Activation
The preparation of activated carbons (ACs) from cherry stones and chemical activation with H3PO4 can be controlled by the experimental variables during the impregnation step in order to obtain a tailored porous structure of the as-prepared ACs. This control not only extends to the ACs’ texture and porosity development, but also to the chemical nature of their surface. The spectroscopic and elemental characterization of different series of ACs is presented in this study. The spectroscopic band features and assignments strongly depend on the H3PO4 concentration and/or the semi-carbonization treatments applied to the feedstock before impregnation, which ultimately influence different characteristics such as the AC hydrophilicity. Different surface chemistries arise from the different tailored impregnation solutions, showing a practical outcome for future applications of the as-prepared ACs.
Open AccessSurface Chemistry of Cherry Stone-Derived Activated Carbon Prepared by H3PO4 Activation
The preparation of activated carbons (ACs) from cherry stones and chemical activation with H3PO4 can be controlled by the experimental variables during the impregnation step in order to obtain a tailored porous structure of the as-prepared ACs. This control not only extends to the ACs’ texture and porosity development, but also to the chemical nature of their surface. The spectroscopic and elemental characterization of different series of ACs is presented in this study. The spectroscopic band features and assignments strongly depend on the H3PO4 concentration and/or the semi-carbonization treatments applied to the feedstock before impregnation, which ultimately influence different characteristics such as the AC hydrophilicity. Different surface chemistries arise from the different tailored impregnation solutions, showing a practical outcome for future applications of the as-prepared ACs.
- 24 March 2020
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (19) , 24342-24354
Adsorption of bisphenol A by activated carbon developed from PET waste by KOH activation
This study deals with the preparation of activated carbon (AC) from poly(ethylene terephthalate) (PET) waste and with the physicochemical characterization of AC and its use as adsorbent of bisphenol A (BPA) in aqueous solution. AC was prepared by chemical activation with KOH and by physical activation in steam. The activation with KOH was carried out by impregnation first of PET by wet and dry routes at the PET/KOH weight ratios of 1:1, 1:3, and 1:5 and by carbonization then of the resulting products at 850 °C for 2 h in N2 atmosphere. The activation in steam was performed by heating at 900 °C for 1 h. The ACs were characterized by N2 adsorption at − 196 °C, mercury porosity, mercury density measurements, FT-IR spectroscopy, and measurement of pH of the point of zero charge (pHpzc). The activation yield is 58.4–49.4% with KOH in aqueous solution, 75.8–23.9% with solid KOH, and 5.9% with steam. Using solid KOH, greater developments of a more heterogeneous porosity with increasing impregnation PET/KOH ratio are achieved. For SK1:5, SBET is 1990 m2 g−1 and the pore volumes are 0.71 cm3 g−1, micropores; 0.81 cm3 g−1, mesopores; and 1.77 cm3 g−1, macropores. The data of BPA adsorption fit better to the Ho and Mckay second order kinetic model than to the Lagergren first-order kinetic model and to the Langmuir equation than to the Freundlich equation. From the kinetic and thermodynamic standpoints, the adsorption process of BPA is more favorable for SK1:5.
- 24 March 2020
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (19) , 24342-24354
Adsorption of bisphenol A by activated carbon developed from PET waste by KOH activation
This study deals with the preparation of activated carbon (AC) from poly(ethylene terephthalate) (PET) waste and with the physicochemical characterization of AC and its use as adsorbent of bisphenol A (BPA) in aqueous solution. AC was prepared by chemical activation with KOH and by physical activation in steam. The activation with KOH was carried out by impregnation first of PET by wet and dry routes at the PET/KOH weight ratios of 1:1, 1:3, and 1:5 and by carbonization then of the resulting products at 850 °C for 2 h in N2 atmosphere. The activation in steam was performed by heating at 900 °C for 1 h. The ACs were characterized by N2 adsorption at − 196 °C, mercury porosity, mercury density measurements, FT-IR spectroscopy, and measurement of pH of the point of zero charge (pHpzc). The activation yield is 58.4–49.4% with KOH in aqueous solution, 75.8–23.9% with solid KOH, and 5.9% with steam. Using solid KOH, greater developments of a more heterogeneous porosity with increasing impregnation PET/KOH ratio are achieved. For SK1:5, SBET is 1990 m2 g−1 and the pore volumes are 0.71 cm3 g−1, micropores; 0.81 cm3 g−1, mesopores; and 1.77 cm3 g−1, macropores. The data of BPA adsorption fit better to the Ho and Mckay second order kinetic model than to the Lagergren first-order kinetic model and to the Langmuir equation than to the Freundlich equation. From the kinetic and thermodynamic standpoints, the adsorption process of BPA is more favorable for SK1:5.
- 12 September 2018
- Published by Springer Nature in Wood Science and Technology
- Vol. 52 (6) , 1645-1669
How does phosphoric acid interact with cherry stones? A discussion on overlooked aspects of chemical activation
- 12 September 2018
- Published by Springer Nature in Wood Science and Technology
- Vol. 52 (6) , 1645-1669
How does phosphoric acid interact with cherry stones? A discussion on overlooked aspects of chemical activation
- 1 October 2016
- Published by Elsevier in Journal of Environmental Management
- Vol. 181, 522-535
Preparation of high-quality activated carbon from polyethyleneterephthalate (PET) bottle waste. Its use in the removal of pollutants in aqueous solution
- 1 October 2016
- Published by Elsevier in Journal of Environmental Management
- Vol. 181, 522-535
Preparation of high-quality activated carbon from polyethyleneterephthalate (PET) bottle waste. Its use in the removal of pollutants in aqueous solution
- 23 February 2016
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 125 (1) , 65-74
Physico-chemical characterization of activated carbon–metal oxide photocatalysts by immersion calorimetry in benzene and water
- 23 February 2016
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 125 (1) , 65-74
Physico-chemical characterization of activated carbon–metal oxide photocatalysts by immersion calorimetry in benzene and water
- 15 February 2016
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 55 (18) , 5200-5206
Preparation of Activated Carbon-SnO2, TiO2, and WO3 Catalysts. Study by FT-IR Spectroscopy
- 15 February 2016
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 55 (18) , 5200-5206
Preparation of Activated Carbon-SnO2, TiO2, and WO3 Catalysts. Study by FT-IR Spectroscopy
- 3 June 2014
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 28 (6) , 4096-4103
FT-IR Analysis of Pyrone and Chromene Structures in Activated Carbon
- 3 June 2014
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 28 (6) , 4096-4103
FT-IR Analysis of Pyrone and Chromene Structures in Activated Carbon