Jian-Qiang Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jian-Qiang Lu has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Ronald J. Gutmann
Rensselaer Polytechnic Institute, Center for Integrated Electronics, Troy, NY, 12180, United States
5 shared publications - Sang Hwui Lee
Rensselaer Polytechnic Institute, Center for Integrated Electronics, 110 8th Street, Troy, NY, 12180, United States
5 shared publications - J. Jay McMahon
Rensselaer Polytechnic Institute, Center for Integrated Electronics, Troy, NY, 12180, United States
4 shared publications Dingyou Zhang
GLOBALFOUNDRIES
3 shared publications- Lijie Ci
Harbin Institute of Technology (Shenzhen)
3 shared publications R.J. Gutmann
Focus Center - New York, Rensselaer: Interconnections for Hyperintegration Rensselaer Polytechnic Institute, Troy, New York 12180-3590
3 shared publications
Latest Publications
- 13 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 32 (8) , 1119-1121
Demonstration and Electrical Performance Investigation of Wafer-Level Cu Oxide Hybrid Bonding Schemes
Wafer-level Cu oxide hybrid bonding owns a number of merits, including simultaneous formations of electrical and mechanical bonds, underfill free, high alignment accuracy, increasing bond strength, and excellent reliability performance in 3-D integration. This letter demonstrates the fabrication of wafer-level Cu oxide hybrid bonding. Investigations of experimental and electrical simulation data of Cu oxide hybrid bonding structures are reported. Their alignment accuracy, frequency responses, and passive elements are compared for 3-D integration applications.
- 13 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 32 (8) , 1119-1121
Demonstration and Electrical Performance Investigation of Wafer-Level Cu Oxide Hybrid Bonding Schemes
Wafer-level Cu oxide hybrid bonding owns a number of merits, including simultaneous formations of electrical and mechanical bonds, underfill free, high alignment accuracy, increasing bond strength, and excellent reliability performance in 3-D integration. This letter demonstrates the fabrication of wafer-level Cu oxide hybrid bonding. Investigations of experimental and electrical simulation data of Cu oxide hybrid bonding structures are reported. Their alignment accuracy, frequency responses, and passive elements are compared for 3-D integration applications.
- 22 April 2011
- Published by Elsevier in Microelectronic Engineering
- Vol. 92, 15-18
A novel chip-to-wafer (C2W) three-dimensional (3D) integration approach using a template for precise alignment
- 22 April 2011
- Published by Elsevier in Microelectronic Engineering
- Vol. 92, 15-18
A novel chip-to-wafer (C2W) three-dimensional (3D) integration approach using a template for precise alignment
- 1 January 2011
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 29 (1) , 011019
Thick benzocyclobutene etching using high density SF6/O2 plasmas
- 1 January 2011
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 29 (1) , 011019
Thick benzocyclobutene etching using high density SF6/O2 plasmas
- 1 January 2010
- Published by IMAPS - International Microelectronics Assembly and Packaging Society in International Symposium on Microelectronics
- Vol. 2010 (1) , 000164-000169
Electrical Analysis and Modeling of 3D Through-Strata-Vias (TSVs) and Pads
Through-strata-via (TSV) is one of the most attractive3D integration solutions in that it offers a massive number of short interstrata connects, high data bandwidth, reduced delay and power consumption, small footprint, improved yield, heterogeneous integration and reduced volume-production cost. This work attempts to investigate the TSV signal integrity and, particularly, compares the performance among different TSV and pad combinations. Transient analysis, eye diagram and bathtub curves show a good behavior of TSV signal integrity in the time domain. Regarding to frequency response, the set of circular TSV and circular pad offers a slightly better performance than other shapes. When a misalignment is so large that the TSV does not land completely within the pad, the TSV frequency response is affected considerably. A big pad size degrades performance and decreases trace density, while a thinner pad would enhance process throughput and reduce cost. Simulation results also indicate that rather than using multiple small TSVs connecting to a common pad, it is better to implement one single big TSV because of less parasitics and coupling. Furthermore, the TSV component is carefully modeled, and the results from electromagnetic simulation and a broadband SPICE model are in a very good agreement.
- 1 January 2010
- Published by IMAPS - International Microelectronics Assembly and Packaging Society in International Symposium on Microelectronics
- Vol. 2010 (1) , 000164-000169
Electrical Analysis and Modeling of 3D Through-Strata-Vias (TSVs) and Pads
Through-strata-via (TSV) is one of the most attractive3D integration solutions in that it offers a massive number of short interstrata connects, high data bandwidth, reduced delay and power consumption, small footprint, improved yield, heterogeneous integration and reduced volume-production cost. This work attempts to investigate the TSV signal integrity and, particularly, compares the performance among different TSV and pad combinations. Transient analysis, eye diagram and bathtub curves show a good behavior of TSV signal integrity in the time domain. Regarding to frequency response, the set of circular TSV and circular pad offers a slightly better performance than other shapes. When a misalignment is so large that the TSV does not land completely within the pad, the TSV frequency response is affected considerably. A big pad size degrades performance and decreases trace density, while a thinner pad would enhance process throughput and reduce cost. Simulation results also indicate that rather than using multiple small TSVs connecting to a common pad, it is better to implement one single big TSV because of less parasitics and coupling. Furthermore, the TSV component is carefully modeled, and the results from electromagnetic simulation and a broadband SPICE model are in a very good agreement.
- 3 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 17 (3) , 447-451
Fully Monolithic Cellular Buck Converter Design for 3-D Power Delivery
A fully monolithic interleaved buck dc-dc point-of-load (PoL) converter has been designed and fabricated in a 0.18-mm SiGe BiCMOS process. Target application of the design is 3-D power delivery for future microprocessors, in which the PoL converter will be vertically integrated with the processor using wafer-level 3-D interconnect technologies. Advantages of 3-D power delivery over conventional discrete voltage regulator modules (VRMs) are discussed. The prototype design, using two interleaved buck converter cells each operating at 200 MHz switching frequency and delivering 500 mA output current, is discussed with a focus on the converter power stage and control loop to highlight the tradeoffs unique to such high-frequency, monolithic designs. Measured steady-state and dynamic responses of the fabricated prototype are presented to demonstrate the ability of such monolithic converters to meet the power delivery requirements of future processors.
- 3 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 17 (3) , 447-451
Fully Monolithic Cellular Buck Converter Design for 3-D Power Delivery
A fully monolithic interleaved buck dc-dc point-of-load (PoL) converter has been designed and fabricated in a 0.18-mm SiGe BiCMOS process. Target application of the design is 3-D power delivery for future microprocessors, in which the PoL converter will be vertically integrated with the processor using wafer-level 3-D interconnect technologies. Advantages of 3-D power delivery over conventional discrete voltage regulator modules (VRMs) are discussed. The prototype design, using two interleaved buck converter cells each operating at 200 MHz switching frequency and delivering 500 mA output current, is discussed with a focus on the converter power stage and control loop to highlight the tradeoffs unique to such high-frequency, monolithic designs. Measured steady-state and dynamic responses of the fabricated prototype are presented to demonstrate the ability of such monolithic converters to meet the power delivery requirements of future processors.
- 11 August 2008
- Published by Springer Nature
- p. 1-38
3D Integration Based upon Dielectric Adhesive Bonding
- 11 August 2008
- Published by Springer Nature
- p. 1-38
3D Integration Based upon Dielectric Adhesive Bonding
- 1 June 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 144-146
Benchmarking of Metal-to-Carbon Nanotube Side Contact Resistance
We report on side-contact resistances of four promising metal/multiwall-carbon-nanotube contacts utilizing transfer length method (TLM) test structures on densified carbon nanotube (CNT) strips formed from vertically-aligned CNT forests. Contact resistances of Ti/CNT, Pd/CNT, Ta/CNT, and W/CNT contacts with the same nominal contact area were extracted to be 40, 49, 108, and 160 Ω, respectively. Rapid thermal annealing at 400 °C for 5 min reduces the Ta/CNT and W/CNT contact resistances while increasing the Ti/CNT and Pd/CNT ones.
- 1 June 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 144-146
Benchmarking of Metal-to-Carbon Nanotube Side Contact Resistance
We report on side-contact resistances of four promising metal/multiwall-carbon-nanotube contacts utilizing transfer length method (TLM) test structures on densified carbon nanotube (CNT) strips formed from vertically-aligned CNT forests. Contact resistances of Ti/CNT, Pd/CNT, Ta/CNT, and W/CNT contacts with the same nominal contact area were extracted to be 40, 49, 108, and 160 Ω, respectively. Rapid thermal annealing at 400 °C for 5 min reduces the Ta/CNT and W/CNT contact resistances while increasing the Ti/CNT and Pd/CNT ones.
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1112
3D Integration Using Adhesive, Metal, and Metal/Adhesive as Wafer Bonding Interfaces
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1112
3D Integration Using Adhesive, Metal, and Metal/Adhesive as Wafer Bonding Interfaces
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 127-133
3D Power Delivery for Microprocessors and High-Performance ASICs
Conventional power delivery methods for microprocessors and high-performance ASICs have fundamental limitations in meeting the power requirements of future IC technologies due to large interconnect parasitics. A new three-dimensional (3D) power delivery approach along with a cellular power supply architecture is proposed as a possible solution to the problems of conventional 2D power delivery. Different 3D integration technologies or possible power-processor integration applications are reviewed, and important 3D design partitioning considerations are discussed. A fully monolithic, two-phase interleaved buck converter design having the potential to be used as a basic building block in a cellular architecture to meet steady-state and dynamic regulation requirements of future processors is presented. Each cell of the converter is designed for 500 mA rated output current, operates at 200 MHz switching frequency, and achieves a control bandwidth of about 10 MHz. Design trade-offs, implementation methods, and prototype results including chip area, loss breakdown, efficiency, as well as dynamic responses to load step changes are presented. Scaling-up of the design through parallel operation of a large number of such standard converter cells is discussed, and the benefits of interleaved operation in drastically reducing the input and output filter size are quantified.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 127-133
3D Power Delivery for Microprocessors and High-Performance ASICs
Conventional power delivery methods for microprocessors and high-performance ASICs have fundamental limitations in meeting the power requirements of future IC technologies due to large interconnect parasitics. A new three-dimensional (3D) power delivery approach along with a cellular power supply architecture is proposed as a possible solution to the problems of conventional 2D power delivery. Different 3D integration technologies or possible power-processor integration applications are reviewed, and important 3D design partitioning considerations are discussed. A fully monolithic, two-phase interleaved buck converter design having the potential to be used as a basic building block in a cellular architecture to meet steady-state and dynamic regulation requirements of future processors is presented. Each cell of the converter is designed for 500 mA rated output current, operates at 200 MHz switching frequency, and achieves a control bandwidth of about 10 MHz. Design trade-offs, implementation methods, and prototype results including chip area, loss breakdown, efficiency, as well as dynamic responses to load step changes are presented. Scaling-up of the design through parallel operation of a large number of such standard converter cells is discussed, and the benefits of interleaved operation in drastically reducing the input and output filter size are quantified.