Ronald J. Gutmann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ronald J. Gutmann has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Jian-Qiang Lu
Rensselaer Polytechnic Institute
5 shared publications - J. Jay McMahon
Rensselaer Polytechnic Institute, Center for Integrated Electronics, Troy, NY, 12180, United States
3 shared publications - R.J. Kumar
Rensselaer Polytechnic Institute
2 shared publications - Sang Hwui Lee
Rensselaer Polytechnic Institute, Center for Integrated Electronics, 110 8th Street, Troy, NY, 12180, United States
2 shared publications - Calvin H. Carter
Cree, Inc., 4600 Silicon Dr., Durham, NC, 27703, United States
1 shared publication David Giuliano
Department of Electrical, Computer, Systems Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180-3590, USA. Telephone: (518)276-8297; Fax: (518)276-6226
1 shared publication
Latest Publications
- 28 August 2009
- Published by Springer Nature
- p. 79-90
Wafer-Level 3D Integration for ULSI Interconnects
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1112
3D Integration Using Adhesive, Metal, and Metal/Adhesive as Wafer Bonding Interfaces
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1112
3D Integration Using Adhesive, Metal, and Metal/Adhesive as Wafer Bonding Interfaces
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 127-133
3D Power Delivery for Microprocessors and High-Performance ASICs
Conventional power delivery methods for microprocessors and high-performance ASICs have fundamental limitations in meeting the power requirements of future IC technologies due to large interconnect parasitics. A new three-dimensional (3D) power delivery approach along with a cellular power supply architecture is proposed as a possible solution to the problems of conventional 2D power delivery. Different 3D integration technologies or possible power-processor integration applications are reviewed, and important 3D design partitioning considerations are discussed. A fully monolithic, two-phase interleaved buck converter design having the potential to be used as a basic building block in a cellular architecture to meet steady-state and dynamic regulation requirements of future processors is presented. Each cell of the converter is designed for 500 mA rated output current, operates at 200 MHz switching frequency, and achieves a control bandwidth of about 10 MHz. Design trade-offs, implementation methods, and prototype results including chip area, loss breakdown, efficiency, as well as dynamic responses to load step changes are presented. Scaling-up of the design through parallel operation of a large number of such standard converter cells is discussed, and the benefits of interleaved operation in drastically reducing the input and output filter size are quantified.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 127-133
3D Power Delivery for Microprocessors and High-Performance ASICs
Conventional power delivery methods for microprocessors and high-performance ASICs have fundamental limitations in meeting the power requirements of future IC technologies due to large interconnect parasitics. A new three-dimensional (3D) power delivery approach along with a cellular power supply architecture is proposed as a possible solution to the problems of conventional 2D power delivery. Different 3D integration technologies or possible power-processor integration applications are reviewed, and important 3D design partitioning considerations are discussed. A fully monolithic, two-phase interleaved buck converter design having the potential to be used as a basic building block in a cellular architecture to meet steady-state and dynamic regulation requirements of future processors is presented. Each cell of the converter is designed for 500 mA rated output current, operates at 200 MHz switching frequency, and achieves a control bandwidth of about 10 MHz. Design trade-offs, implementation methods, and prototype results including chip area, loss breakdown, efficiency, as well as dynamic responses to load step changes are presented. Scaling-up of the design through parallel operation of a large number of such standard converter cells is discussed, and the benefits of interleaved operation in drastically reducing the input and output filter size are quantified.
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 970
Damascene-Patterned Metal-Adhesive (Cu-BCB) Redistribution Layers
A monolithic, wafer-level three-dimensional (3D) technology platform is described that is compatible with next-generation wafer level packaging (WLP) processes. The platform combines the advantages of both (1) high bonding strength and adaptability to IC wafer topography variations with spin-on dielectric adhesive bonding and (2) process integration and via-area advantages of metal-metal bonding. A copper-benzocyclobutene (Cu-BCB) process is described that incorporates single-level damascene-patterned Cu vias with partially-cured BCB as the bonding adhesive layer. A demonstration vehicle consisting of a two-wafer stack of 2-4 μm diameter vias has shown the bondability of both Cu-to-Cu and BCB-to-BCB. Planarization conditions to achieve BCB-BCB bonding with low-resistance Cu-Cu contacts have been examined, with wafer-scale planarization requirements compared to other 3D platforms. Concerns about stress induced at the tantalum (Ta) liner-to-BCB interface resulting in partial delamination are discussed. While across-wafer uniformity has not been demonstrated, the viability of this WLP-compatible 3D platform has been shown.
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 970
Damascene-Patterned Metal-Adhesive (Cu-BCB) Redistribution Layers
A monolithic, wafer-level three-dimensional (3D) technology platform is described that is compatible with next-generation wafer level packaging (WLP) processes. The platform combines the advantages of both (1) high bonding strength and adaptability to IC wafer topography variations with spin-on dielectric adhesive bonding and (2) process integration and via-area advantages of metal-metal bonding. A copper-benzocyclobutene (Cu-BCB) process is described that incorporates single-level damascene-patterned Cu vias with partially-cured BCB as the bonding adhesive layer. A demonstration vehicle consisting of a two-wafer stack of 2-4 μm diameter vias has shown the bondability of both Cu-to-Cu and BCB-to-BCB. Planarization conditions to achieve BCB-BCB bonding with low-resistance Cu-Cu contacts have been examined, with wafer-scale planarization requirements compared to other 3D platforms. Concerns about stress induced at the tantalum (Ta) liner-to-BCB interface resulting in partial delamination are discussed. While across-wafer uniformity has not been demonstrated, the viability of this WLP-compatible 3D platform has been shown.
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 911
High Carrier Lifetime Bulk-Grown 4H-SiC Substrates for Power Applications
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 911
High Carrier Lifetime Bulk-Grown 4H-SiC Substrates for Power Applications
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 914
Low-Temperature PETEOS-to-PETEOS Wafer Bonding Using Titanium as Bonding Intermediate
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 914
Low-Temperature PETEOS-to-PETEOS Wafer Bonding Using Titanium as Bonding Intermediate
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 914
Fine Keyed Alignment and Bonding for Wafer-Level 3D ICs
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 914
Fine Keyed Alignment and Bonding for Wafer-Level 3D ICs