John Y. Walz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
John Y. Walz has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Kathy Lu
Department of Mechanical and Materials Engineering, University of Alabama at Birmingham, Birmingham, USA
2 shared publications - Wenle Li
Department of Chemical Engineering, Virginia Tech, Blacksburg, USA
2 shared publications Clayton T. McKee
Department of Chemical Engineering, Virginia Tech, Blacksburg, Virginia 24061
1 shared publicationKathy Lu
Materials Science and Engineering Department, 211B Holden Hall, Virginia Tech, Blacksburg, Virginia 24060, United States
1 shared publicationRatna J. Oetama
Department of Chemical Engineering, Yale University, New Haven, Connecticut 06520, USA
1 shared publicationWenle Li
Materials Science and Engineering Department, 127 Randolph Hall, Virginia Tech, Blacksburg, Virginia 24060, USA
1 shared publication
Latest Publications
- 6 November 2012
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 28 (47) , 16423-16429
Fabrication of Porous Nanocomposites with Controllable Specific Surface Area and Strength via Suspension Infiltration
Porous ceramics are promising candidates for a variety of applications, including separation membranes, catalyst supports, tissue engineering scaffolds, energy storage devices, and microelectronics. We describe a novel method for creating porous ceramics with controllable specific surface area and high strength. The fabrication procedure involves infiltrating aqueous suspensions of silica nanoparticles into a porous ceramic scaffold. The samples are then freeze-dried to maintain a homogeneous distribution of nanoparticles, followed by partial sintering to bond the infiltrated nanoparticles into place. By repeating this infiltration process multiple times, the specific surface area of the composite can be varied from less than one to well over 100 m2/g. It is also found that this infiltration increases the mechanical strength of the composite. Water flux experiments demonstrate the potential use of these materials as liquid membranes, with no detectable damage to the structure observed after these flux tests. While this initial work focused on silica nanoparticles and ceramic scaffolds, the basic approach would to applicable to a wide variety of other materials, meaning that the method described here would be generally applicable for creating porous materials with precisely controllable properties.
- 6 November 2012
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 28 (47) , 16423-16429
Fabrication of Porous Nanocomposites with Controllable Specific Surface Area and Strength via Suspension Infiltration
Porous ceramics are promising candidates for a variety of applications, including separation membranes, catalyst supports, tissue engineering scaffolds, energy storage devices, and microelectronics. We describe a novel method for creating porous ceramics with controllable specific surface area and high strength. The fabrication procedure involves infiltrating aqueous suspensions of silica nanoparticles into a porous ceramic scaffold. The samples are then freeze-dried to maintain a homogeneous distribution of nanoparticles, followed by partial sintering to bond the infiltrated nanoparticles into place. By repeating this infiltration process multiple times, the specific surface area of the composite can be varied from less than one to well over 100 m2/g. It is also found that this infiltration increases the mechanical strength of the composite. Water flux experiments demonstrate the potential use of these materials as liquid membranes, with no detectable damage to the structure observed after these flux tests. While this initial work focused on silica nanoparticles and ceramic scaffolds, the basic approach would to applicable to a wide variety of other materials, meaning that the method described here would be generally applicable for creating porous materials with precisely controllable properties.
- 13 June 2012
- Published by Springer Nature in Journal of Materials Science
- Vol. 47 (19) , 6882-6890
Effects of added kaolinite on the strength and porosity of freeze-cast kaolinite–silica nanocomposites
- 13 June 2012
- Published by Springer Nature in Journal of Materials Science
- Vol. 47 (19) , 6882-6890
Effects of added kaolinite on the strength and porosity of freeze-cast kaolinite–silica nanocomposites
- 10 November 2010
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 94 (4) , 1256-1264
Formation, Structure and Properties of Freeze-Cast Kaolinite-Silica Nanocomposites
- 10 November 2010
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 94 (4) , 1256-1264
Formation, Structure and Properties of Freeze-Cast Kaolinite-Silica Nanocomposites
- 9 April 2009
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 92 (4) , 916-921
Effects of Added Clay on the Properties of Freeze‐Casted Composites of Silica Nanoparticles
An experimental study was performed to investigate the effects of added clay particles on the structure and properties of porous, freeze‐dried composites produced from silica nanoparticles. The sol–gel transition of the silica suspension arrests the sedimentation of the dense clay platelets to produce a gel, containing large clay particles dispersed throughout. No chemical additives other than sodium chloride were needed to cause the gelation. Dry composites were obtained by subjecting the gelled suspensions to rapid freezing in one of the following ways: submersion in liquid nitrogen or liquid propane, or exposure to low‐temperature refrigeration. Frozen samples were then sublimated under vacuum to remove the water. Scanning electron microscope images of the dried composites showed a porous material whose pore sizes decrease with an increasing rate of freezing. The dependence on freeze rate suggests that the porous structure is the result of ice formation. Addition of the clay particles significantly increases the rate of gel formation. Furthermore, the strength of the clay/nanoparticle composites, as measured by normal compression tests, was substantially greater than that of a similar material made with only silica nanoparticles. Finally, BET surface area analysis shows a decreasing surface area with increasing volume fraction of clay at a constant volume fraction of silica.
- 9 April 2009
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 92 (4) , 916-921
Effects of Added Clay on the Properties of Freeze‐Casted Composites of Silica Nanoparticles
An experimental study was performed to investigate the effects of added clay particles on the structure and properties of porous, freeze‐dried composites produced from silica nanoparticles. The sol–gel transition of the silica suspension arrests the sedimentation of the dense clay platelets to produce a gel, containing large clay particles dispersed throughout. No chemical additives other than sodium chloride were needed to cause the gelation. Dry composites were obtained by subjecting the gelled suspensions to rapid freezing in one of the following ways: submersion in liquid nitrogen or liquid propane, or exposure to low‐temperature refrigeration. Frozen samples were then sublimated under vacuum to remove the water. Scanning electron microscope images of the dried composites showed a porous material whose pore sizes decrease with an increasing rate of freezing. The dependence on freeze rate suggests that the porous structure is the result of ice formation. Addition of the clay particles significantly increases the rate of gel formation. Furthermore, the strength of the clay/nanoparticle composites, as measured by normal compression tests, was substantially greater than that of a similar material made with only silica nanoparticles. Finally, BET surface area analysis shows a decreasing surface area with increasing volume fraction of clay at a constant volume fraction of silica.
- 28 April 2006
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 124 (16) , 164713
Simultaneous investigation of sedimentation and diffusion of a single colloidal particle near an interface
We describe here a new procedure for the simultaneous investigation of sedimentation and diffusion of a colloidal particle in close proximity to a solid, planar wall. The measurements were made using the optical technique of total internal reflection microscopy, coupled with optical radiation pressure, for dimensionless separation distances (gap width/radius of particle) ranging from 0.01 to 0.05. In this region, the hydrodynamic mobility and diffusion coefficient are substantially reduced below bulk values. The procedure involved measuring the mean and the variance of vertical displacements of a Brownian particle settling under gravity toward the plate. The spatially varying diffusion coefficient was calculated from the displacements at small times (where diffusive motion was dominant). The mobility relationship for motion normal to a flat plate was tested by measuring the average distance of travel versus time as the particle settled under the constant force of gravity. For the simple Newtonian fluid used here (aqueous salt solution), the magnitude of the diffusion coefficient and mobility, plus their dependence on separation distance, showed excellent agreement with predictions. This new technique could be of great value in measuring the mobility and diffusion coefficient for near-contact motion in more complex fluids for which the hydrodynamic correction factors are not known a priori, such as shear-thinning fluids.
- 28 April 2006
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 124 (16) , 164713
Simultaneous investigation of sedimentation and diffusion of a single colloidal particle near an interface
We describe here a new procedure for the simultaneous investigation of sedimentation and diffusion of a colloidal particle in close proximity to a solid, planar wall. The measurements were made using the optical technique of total internal reflection microscopy, coupled with optical radiation pressure, for dimensionless separation distances (gap width/radius of particle) ranging from 0.01 to 0.05. In this region, the hydrodynamic mobility and diffusion coefficient are substantially reduced below bulk values. The procedure involved measuring the mean and the variance of vertical displacements of a Brownian particle settling under gravity toward the plate. The spatially varying diffusion coefficient was calculated from the displacements at small times (where diffusive motion was dominant). The mobility relationship for motion normal to a flat plate was tested by measuring the average distance of travel versus time as the particle settled under the constant force of gravity. For the simple Newtonian fluid used here (aqueous salt solution), the magnitude of the diffusion coefficient and mobility, plus their dependence on separation distance, showed excellent agreement with predictions. This new technique could be of great value in measuring the mobility and diffusion coefficient for near-contact motion in more complex fluids for which the hydrodynamic correction factors are not known a priori, such as shear-thinning fluids.