Ryan L. Karkkainen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ryan L. Karkkainen has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
Jerome T. Tzeng
Weapons and Materials Research Directorate, U.S. Army Research Laboratory Aberdeen Proving Ground, MD 21005, USA
1 shared publication- Jerome T. Tzeng1 shared publication
Paul Moy
1 shared publication
Latest Publications
- 9 September 2009
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 43 (25) , 3125-3142
Micromechanical Strength Modeling and Investigation of Stitch Density Effects on 3D Orthogonal Composites
A 3D orthogonal woven S2-glass composite is investigated using finite element micromechanics to characterize the stiffness and the strength. The methods are applied to a targeted parametric investigation of the effects of stitch density on strength properties and potential benefits of through-thickness reinforcement, such as resistance to transverse shear and delamination, with some consequent loss of in-plane properties. Direct modeling of the exact microstructure from scanning electron microscope visualization provides a precise knowledge of the mechanics and the failure modes of the microstructure under various loading conditions. Modeling results are verified by comparison to experimental data. In-plane stiffness and strength are predicted with 90% or better accuracy. Transverse shear stiffness was less well predicted, but strength was still predicted within 86% accuracy.
- 9 September 2009
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 43 (25) , 3125-3142
Micromechanical Strength Modeling and Investigation of Stitch Density Effects on 3D Orthogonal Composites
A 3D orthogonal woven S2-glass composite is investigated using finite element micromechanics to characterize the stiffness and the strength. The methods are applied to a targeted parametric investigation of the effects of stitch density on strength properties and potential benefits of through-thickness reinforcement, such as resistance to transverse shear and delamination, with some consequent loss of in-plane properties. Direct modeling of the exact microstructure from scanning electron microscope visualization provides a precise knowledge of the mechanics and the failure modes of the microstructure under various loading conditions. Modeling results are verified by comparison to experimental data. In-plane stiffness and strength are predicted with 90% or better accuracy. Transverse shear stiffness was less well predicted, but strength was still predicted within 86% accuracy.
- Open Access
- 1 April 2009
- Published by Defense Technical Information Center (DTIC)
Through-Thickness Property Measurement of Three-Dimensional Textile Composites
Three-dimensional (3-D) reinforcement of thick composite parts is utilized to increase delamination resistance and through-thickness properties, which often represent the weak link of such structures. Stitching, z-pinning, or a 3-D textile weave may be employed. In the current study of a 3-D, orthogonal-woven, glass-epoxy composite, a specimen is designed for cases in which a sufficiently thick specimen for standard test setups cannot be created due to manufacturing limitations. A minimum width is dictated by the need to capture a sufficient number of through-thickness stitches in the specimen cross section. Thickness is limited by manufacturing feasibility, as stitches can only penetrate through a certain thickness, and further limitation is imposed by the ability of resin to penetrate the fiber preform during cure. Thus, a specimen must accommodate this low aspect ratio geometry. To this end, several specimens have been designed using finite-element method analysis and validated experimentally. Multiple specimen types were investigated to determine an optimum specimen and to ensure geometry independence of the obtained properties. Optimized specimens have shown good agreement with stiffness predictions as well as promising, consistent results for strength determination.
- 1 April 2009
- Published by Defense Technical Information Center (DTIC)
Open AccessThrough-Thickness Property Measurement of Three-Dimensional Textile Composites
Three-dimensional (3-D) reinforcement of thick composite parts is utilized to increase delamination resistance and through-thickness properties, which often represent the weak link of such structures. Stitching, z-pinning, or a 3-D textile weave may be employed. In the current study of a 3-D, orthogonal-woven, glass-epoxy composite, a specimen is designed for cases in which a sufficiently thick specimen for standard test setups cannot be created due to manufacturing limitations. A minimum width is dictated by the need to capture a sufficient number of through-thickness stitches in the specimen cross section. Thickness is limited by manufacturing feasibility, as stitches can only penetrate through a certain thickness, and further limitation is imposed by the ability of resin to penetrate the fiber preform during cure. Thus, a specimen must accommodate this low aspect ratio geometry. To this end, several specimens have been designed using finite-element method analysis and validated experimentally. Multiple specimen types were investigated to determine an optimum specimen and to ensure geometry independence of the obtained properties. Optimized specimens have shown good agreement with stiffness predictions as well as promising, consistent results for strength determination.