Jerome T. Tzeng
Research Interests
Jerome T. Tzeng has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
Paul Moy
2 shared publications- Ryan Emerson
US Army Research Laboratory, Materials Division, Weapons and Materials Research Directorate, Ordnance Materials Branch , Aberdeen Proving Ground, Maryland, USA
2 shared publications - Daniel J. O'Brien
Department of Radiation Physics, University of Texas MD Anderson Cancer Center, Houston, TX 77030, USA
1 shared publication - Ryan L. Karkkainen
Weapons and Materials Research Directorate, U.S. Army Research Laboratory Aberdeen Proving Ground, MD 21005, USA
1 shared publication
Latest Publications
- 1 February 2013
- Published by Defense Technical Information Center (DTIC)
Viscoelasticity of Axisymmetric Composite Structures: Analysis and Experimental Validation
Stress relaxation and creep of composite cylinders are investigated based on anisotropic viscoelasticity. The analysis accounts for ply-by-ply variation of material properties, ply orientations, and temperature gradients through the thickness of cylinders subjected to mechanical and thermal loads. Experimental validation of the model is conducted using a high tensioned composite overwrapped on a steel cylinder. The creep and stress relaxation response of composite is accelerated at elevated temperatures, then characterized and compared with the model simulation. Fiber-reinforced composite materials generally illustrate extreme anisotropy in viscoelastic behavior. Accordingly, viscoelastic characteristics of composite cylinders are quite different from those of isotropic cylinders. Viscoelastic effects of the composite can result in a drastic change of stress and strain profiles in the cylinders over a period of time, which is critical for structural durability of composite cylinders. The developed analysis can be applied to composite pressure vessels, gun barrels, and flywheels.
- 1 February 2013
- Published by Defense Technical Information Center (DTIC)
Viscoelasticity of Axisymmetric Composite Structures: Analysis and Experimental Validation
Stress relaxation and creep of composite cylinders are investigated based on anisotropic viscoelasticity. The analysis accounts for ply-by-ply variation of material properties, ply orientations, and temperature gradients through the thickness of cylinders subjected to mechanical and thermal loads. Experimental validation of the model is conducted using a high tensioned composite overwrapped on a steel cylinder. The creep and stress relaxation response of composite is accelerated at elevated temperatures, then characterized and compared with the model simulation. Fiber-reinforced composite materials generally illustrate extreme anisotropy in viscoelastic behavior. Accordingly, viscoelastic characteristics of composite cylinders are quite different from those of isotropic cylinders. Viscoelastic effects of the composite can result in a drastic change of stress and strain profiles in the cylinders over a period of time, which is critical for structural durability of composite cylinders. The developed analysis can be applied to composite pressure vessels, gun barrels, and flywheels.
- Open Access
- 1 April 2009
- Published by Defense Technical Information Center (DTIC)
Through-Thickness Property Measurement of Three-Dimensional Textile Composites
Three-dimensional (3-D) reinforcement of thick composite parts is utilized to increase delamination resistance and through-thickness properties, which often represent the weak link of such structures. Stitching, z-pinning, or a 3-D textile weave may be employed. In the current study of a 3-D, orthogonal-woven, glass-epoxy composite, a specimen is designed for cases in which a sufficiently thick specimen for standard test setups cannot be created due to manufacturing limitations. A minimum width is dictated by the need to capture a sufficient number of through-thickness stitches in the specimen cross section. Thickness is limited by manufacturing feasibility, as stitches can only penetrate through a certain thickness, and further limitation is imposed by the ability of resin to penetrate the fiber preform during cure. Thus, a specimen must accommodate this low aspect ratio geometry. To this end, several specimens have been designed using finite-element method analysis and validated experimentally. Multiple specimen types were investigated to determine an optimum specimen and to ensure geometry independence of the obtained properties. Optimized specimens have shown good agreement with stiffness predictions as well as promising, consistent results for strength determination.
- 1 April 2009
- Published by Defense Technical Information Center (DTIC)
Open AccessThrough-Thickness Property Measurement of Three-Dimensional Textile Composites
Three-dimensional (3-D) reinforcement of thick composite parts is utilized to increase delamination resistance and through-thickness properties, which often represent the weak link of such structures. Stitching, z-pinning, or a 3-D textile weave may be employed. In the current study of a 3-D, orthogonal-woven, glass-epoxy composite, a specimen is designed for cases in which a sufficiently thick specimen for standard test setups cannot be created due to manufacturing limitations. A minimum width is dictated by the need to capture a sufficient number of through-thickness stitches in the specimen cross section. Thickness is limited by manufacturing feasibility, as stitches can only penetrate through a certain thickness, and further limitation is imposed by the ability of resin to penetrate the fiber preform during cure. Thus, a specimen must accommodate this low aspect ratio geometry. To this end, several specimens have been designed using finite-element method analysis and validated experimentally. Multiple specimen types were investigated to determine an optimum specimen and to ensure geometry independence of the obtained properties. Optimized specimens have shown good agreement with stiffness predictions as well as promising, consistent results for strength determination.
- 1 January 2005
- Published by Defense Technical Information Center (DTIC)
Composite Flywheel Development for Energy Storage
Composite flywheels for energy storage have been proposed and investigated for the past several decades. Successful applications are, however, limited due to the inability to predict the performance, especially the long-term durability. In this investigation, a comprehensive study was proposed with the intent to implement composites in high-performance flywheels. The potential failure mechanism of flywheels constructed with fiber composites was evaluated. Analytical codes for predicting elastic and viscoelastic (long-term) behavior were developed for flywheel design. Material characterization and test matrices were proposed to design flywheels with maximum performance. Component-level test methods and devices were developed to validate flywheel performance. Finally, a methodology incorporating these studies is presented for the design and manufacture of composite flywheels.
- 1 January 2005
- Published by Defense Technical Information Center (DTIC)
Composite Flywheel Development for Energy Storage
Composite flywheels for energy storage have been proposed and investigated for the past several decades. Successful applications are, however, limited due to the inability to predict the performance, especially the long-term durability. In this investigation, a comprehensive study was proposed with the intent to implement composites in high-performance flywheels. The potential failure mechanism of flywheels constructed with fiber composites was evaluated. Analytical codes for predicting elastic and viscoelastic (long-term) behavior were developed for flywheel design. Material characterization and test matrices were proposed to design flywheels with maximum performance. Component-level test methods and devices were developed to validate flywheel performance. Finally, a methodology incorporating these studies is presented for the design and manufacture of composite flywheels.