Edmundas Kibirkštis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Edmundas Kibirkštis has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Darius Pauliukaitis
Department of Production Engineering, Kaunas University of Technology, Studentu Str. 56, 51424 Kaunas, Lithuania
6 shared publications - Kęstutis Vaitasius
Department of Production Engineering, Kaunas University of Technology, Studentu Str. 56, 51424 Kaunas, Lithuania
5 shared publications - Ingrida Venytė
Department of Production Engineering, Kaunas University of Technology, Studentu Str. 56, 51424 Kaunas, Lithuania
4 shared publications - Laura Gegeckienė
Department of Production Engineering, Kaunas University of Technology, Studentu Str. 56, 51424 Kaunas, Lithuania
4 shared publications - V. Miliūnas
1 Kaunas University of Technology, Department of Manufacturing Engineering, Studentų 56-350, LT-51424, Kaunas, Lithuania
4 shared publications - Liutauras Ragulskis
2 Department of Systems Analysis, Faculty of Informatics, Vytautas Magnus University, Vileikos str. 8, LT-44404, Kaunas, Lithuania
3 shared publications
Latest Publications
- Open Access
- 5 August 2026
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 32 (3) , 220-227
Mechanical and Geometric Optimization of Laser Cutting Processes for HDF Components Used in Packaging and Printing Products
The article presents a method for mechanical and geometric optimization of laser cutting processes for HDF (High Density Fiberboard) components used in packaging and printing products. The proposed approach combines polygon-based nesting algorithms with technological constraints of laser processing and mechanical characteristics of sheet materials. The developed model considers irregular geometry of parts, laser kerf width, minimum technological gaps, material anisotropy, and thermal influence during cutting. A multi-criteria optimization function is introduced, which simultaneously minimizes material waste, cutting path length, and mechanical degradation of produced components. The developed algorithm is based on a combination of geometric preprocessing, Bottom-Left placement strategy, inner nesting optimization, and common-line cutting principles. The proposed solution allows increasing material utilization efficiency and improving the functional quality of manufactured HDF components.
- 5 August 2026
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 32 (3) , 220-227
Open AccessMechanical and Geometric Optimization of Laser Cutting Processes for HDF Components Used in Packaging and Printing Products
The article presents a method for mechanical and geometric optimization of laser cutting processes for HDF (High Density Fiberboard) components used in packaging and printing products. The proposed approach combines polygon-based nesting algorithms with technological constraints of laser processing and mechanical characteristics of sheet materials. The developed model considers irregular geometry of parts, laser kerf width, minimum technological gaps, material anisotropy, and thermal influence during cutting. A multi-criteria optimization function is introduced, which simultaneously minimizes material waste, cutting path length, and mechanical degradation of produced components. The developed algorithm is based on a combination of geometric preprocessing, Bottom-Left placement strategy, inner nesting optimization, and common-line cutting principles. The proposed solution allows increasing material utilization efficiency and improving the functional quality of manufactured HDF components.
- Open Access
- 6 July 2025
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 31 (3) , 237-242
Development and Research of the Laser Engraving Process in Packaging Manufacturing Technology
The areas of application of carbon dioxide lasers in the printing industry are given. A technological process for laser engraving of packaging made of wood-fiber materials has been developed. Experimental studies of the influence of the parameters of CO2 laser radiation on the engraving process of HDF material, which is widely used in the packaging industry, have been conducted. The dependence of the engraving depth on changes in the speed and power of laser radiation has been studied. Based on the experimental studies conducted, the main operating, technological and operational factors affecting the quality of engraving have been identified.
- 6 July 2025
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 31 (3) , 237-242
Open AccessDevelopment and Research of the Laser Engraving Process in Packaging Manufacturing Technology
The areas of application of carbon dioxide lasers in the printing industry are given. A technological process for laser engraving of packaging made of wood-fiber materials has been developed. Experimental studies of the influence of the parameters of CO2 laser radiation on the engraving process of HDF material, which is widely used in the packaging industry, have been conducted. The dependence of the engraving depth on changes in the speed and power of laser radiation has been studied. Based on the experimental studies conducted, the main operating, technological and operational factors affecting the quality of engraving have been identified.
- Open Access
- 8 March 2025
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 31 (1) , 60-66
Development and Research of Technologies and Methods of Electro-flocking in the Decoration of Packaging Products
The aim of this work is to analyze the modern electroflocking technology and to develop a new method for printing a color image on white flocked material. For packaging material, High Density Fiberboard (HDF) with a 3 mm thick white painted coating was chosen. Printing was carried out using DTI InkTec sublimation inks on an Epson L132 inkjet printer, followed by image transfer in an Amazon MAX 400C heat press. The image was applied to a 0.5 mm thick SEF FiberPlus thermal transfer sublimation flock film, which contains exclusive polyester microfibers and 100% polyurethane resins. Cutting of the packaging components was performed using a TS1390 CO2 laser cutting machine with a wavelength of 10.6 µm. Image quality was evaluated using operational control scales. Microscopic photographs were taken at 60x magnification. Image fixation in the heat press was done using the following parameters: transfer temperature 170°C, transfer time 40 seconds, and pressure 3.0 bar. As shown by microscopic studies, the reason for the reduced optical density of the printed image with sublimation inks on flocked film is its high porosity. Therefore, to enhance the decorative effect and give the packaging an attractive velvety appearance, it is advisable to use a combination of printing on flocked material with cutting out several differently shaped and colored images from the flocked material.
- 8 March 2025
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 31 (1) , 60-66
Open AccessDevelopment and Research of Technologies and Methods of Electro-flocking in the Decoration of Packaging Products
The aim of this work is to analyze the modern electroflocking technology and to develop a new method for printing a color image on white flocked material. For packaging material, High Density Fiberboard (HDF) with a 3 mm thick white painted coating was chosen. Printing was carried out using DTI InkTec sublimation inks on an Epson L132 inkjet printer, followed by image transfer in an Amazon MAX 400C heat press. The image was applied to a 0.5 mm thick SEF FiberPlus thermal transfer sublimation flock film, which contains exclusive polyester microfibers and 100% polyurethane resins. Cutting of the packaging components was performed using a TS1390 CO2 laser cutting machine with a wavelength of 10.6 µm. Image quality was evaluated using operational control scales. Microscopic photographs were taken at 60x magnification. Image fixation in the heat press was done using the following parameters: transfer temperature 170°C, transfer time 40 seconds, and pressure 3.0 bar. As shown by microscopic studies, the reason for the reduced optical density of the printed image with sublimation inks on flocked film is its high porosity. Therefore, to enhance the decorative effect and give the packaging an attractive velvety appearance, it is advisable to use a combination of printing on flocked material with cutting out several differently shaped and colored images from the flocked material.
- Open Access
Research of Multi-Mode Pneumatic Vibroactuator
A multi-functional, three-mode, self-exciting pneumatic vibroactuator was investigated. The special feature of this vibroactuator is that it consists of two excitation chambers connected by an elastic synchronizing chain. A mathematical model of the vibroactuator was created, which was solved by numerical methods. The laws (modes) of the movement of the working organ of this vibroactuator have been determined: harmonic, non-harmonic, and pulsating. The results of numerical and experimental research are compared. The vibroactuator with these extended functional capabilities can be used for the intensification of various production technological processes.
Open AccessResearch of Multi-Mode Pneumatic Vibroactuator
A multi-functional, three-mode, self-exciting pneumatic vibroactuator was investigated. The special feature of this vibroactuator is that it consists of two excitation chambers connected by an elastic synchronizing chain. A mathematical model of the vibroactuator was created, which was solved by numerical methods. The laws (modes) of the movement of the working organ of this vibroactuator have been determined: harmonic, non-harmonic, and pulsating. The results of numerical and experimental research are compared. The vibroactuator with these extended functional capabilities can be used for the intensification of various production technological processes.
- Open Access
- 19 April 2023
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 29 (2) , 162-167
Research on a Single-Chamber Pneumatic Vibroactuator
The linear type single-chamber pneumatic vibro- actuator is widely used in industrial automation due to its fast response, low energy consumption, and high-power density. Many researchers have conducted studies on the dynamic behaviour of pneumatic actuators to optimize their performance. A pneumatic vibroexciter with one chamber was investigated in this study. A simulation model was developed in the MATLAB environment to conduct theoretical studies. The simulation results were compared with experimental measurements previously made by the authors of this paper. The findings of this study can be utilized to optimize the design and control of pneumatic actuators in industrial automation.
- 19 April 2023
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 29 (2) , 162-167
Open AccessResearch on a Single-Chamber Pneumatic Vibroactuator
The linear type single-chamber pneumatic vibro- actuator is widely used in industrial automation due to its fast response, low energy consumption, and high-power density. Many researchers have conducted studies on the dynamic behaviour of pneumatic actuators to optimize their performance. A pneumatic vibroexciter with one chamber was investigated in this study. A simulation model was developed in the MATLAB environment to conduct theoretical studies. The simulation results were compared with experimental measurements previously made by the authors of this paper. The findings of this study can be utilized to optimize the design and control of pneumatic actuators in industrial automation.
- Open Access
- 13 November 2019
- Published by IntechOpen
Research on Shape Memory Alloys and Magnetorheological Fluids for Use in Pneumatic Actuators
Adaptive vibrating actuators operating under autovibration regime were developed using materials with shape memory (SM). Mechanical characteristics of such type vibroactuators can be adjusted by changing geometrical parameters of chamber or throttle. It allows to expand the application of pneumatic vibroexciters and use them in different technological processes. Pneumatic vibroactuator elements that consist of magnetorheological (MR) fluids are proposed for micro-throttle and microcompressor design. The main properties of used MR materials and theoretical background of their mechanical and physical parameters are presented, some results of experimental and theoretical research of actuators are introduced and conclusions of the performed research are formulated.
- 13 November 2019
- Published by IntechOpen
Open AccessResearch on Shape Memory Alloys and Magnetorheological Fluids for Use in Pneumatic Actuators
Adaptive vibrating actuators operating under autovibration regime were developed using materials with shape memory (SM). Mechanical characteristics of such type vibroactuators can be adjusted by changing geometrical parameters of chamber or throttle. It allows to expand the application of pneumatic vibroexciters and use them in different technological processes. Pneumatic vibroactuator elements that consist of magnetorheological (MR) fluids are proposed for micro-throttle and microcompressor design. The main properties of used MR materials and theoretical background of their mechanical and physical parameters are presented, some results of experimental and theoretical research of actuators are introduced and conclusions of the performed research are formulated.
- 28 August 2019
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 25 (4) , 313-319
Influence of Structure and Physical-Mechanical Characteristics of Threads on the Strength of Binding the Books
In this study was analyzed the physical-mechanical properties and characteristics of different type of threads (linen, polyamide, cotton, polyester, silky) for blocks sewing. Investigated the brochure block binding with reduced threads surface friction coefficient, physical-mechanical parameters analysis. An important step in calculating the strength of threads for book sections and book blocks sewing is the choice of the strength criterion. For this purpose, are analyzed the influence of the structure of cotton and polyamide threads antifriction. Here was made the book binding process optimization with different types of the thread. It has been determined that the strongest book binding is with the polyamide type thread.
- 28 August 2019
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 25 (4) , 313-319
Influence of Structure and Physical-Mechanical Characteristics of Threads on the Strength of Binding the Books
In this study was analyzed the physical-mechanical properties and characteristics of different type of threads (linen, polyamide, cotton, polyester, silky) for blocks sewing. Investigated the brochure block binding with reduced threads surface friction coefficient, physical-mechanical parameters analysis. An important step in calculating the strength of threads for book sections and book blocks sewing is the choice of the strength criterion. For this purpose, are analyzed the influence of the structure of cotton and polyamide threads antifriction. Here was made the book binding process optimization with different types of the thread. It has been determined that the strongest book binding is with the polyamide type thread.
- 7 March 2019
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 25 (1) , 82-86-86
Research of durability of Braille formed in paper
Research of durability of Braille formed in paper
- 7 March 2019
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 25 (1) , 82-86-86
Research of durability of Braille formed in paper
Research of durability of Braille formed in paper
- 15 January 2019
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 34 (1) , 117-127
Model to predict the top-to-bottom compressive strength of folding cartons
This paper presents a proposed mathematical model, describing the calculations involved in deducting the critical compression force for rectangular, parallelepiped paperboard packaging, and permitting the minimisation of the thickness of the package sidewall. A comparison is given between the obtained calculations regarding critical force and the experimentally-determined results. This has shown a sufficient level of accuracy both for the theoretical and the experimental results. This means that the proposed mathematical engineering calculations model can be applied to the design of rectangular, parallelepiped paperboard packaging.
- 15 January 2019
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 34 (1) , 117-127
Model to predict the top-to-bottom compressive strength of folding cartons
This paper presents a proposed mathematical model, describing the calculations involved in deducting the critical compression force for rectangular, parallelepiped paperboard packaging, and permitting the minimisation of the thickness of the package sidewall. A comparison is given between the obtained calculations regarding critical force and the experimentally-determined results. This has shown a sufficient level of accuracy both for the theoretical and the experimental results. This means that the proposed mathematical engineering calculations model can be applied to the design of rectangular, parallelepiped paperboard packaging.
- 23 January 2018
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 32 (1) , 81-89
Synchronization of pneumatic vibroexciters operating on air cushion with feeding pulsatile pressure under autovibration regime
- 23 January 2018
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 32 (1) , 81-89
Synchronization of pneumatic vibroexciters operating on air cushion with feeding pulsatile pressure under autovibration regime