K. Tsuzuki
Research Subjects
K. Tsuzuki has a total of 160 co-authors. Here are the top co-authors by number of shared publications:
H. Kimura
Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Tokai-mura 319-1195, Japan
6 shared publicationsM. Sato
Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Tokai-mura 319-1195, Japan
6 shared publicationsY. Miura
5 shared publicationsH. Kawashima
Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Tokai-mura 319-1195, Japan
4 shared publicationsN. Isei
Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Tokai-mura 319-1195, Japan
4 shared publications- H. Kawashima
Japan Atomic Energy Agency, 801-1, Mukoyama, Naka, Ibaraki 311-0193, Japan
3 shared publications
Latest Publications
- 10 January 2006
- Published by Elsevier in Fusion Engineering and Design
- Vol. 81 (8) , 925-929
Exposure of reduced activation ferritic steel F82H to TEXTOR plasma
- 10 January 2006
- Published by Elsevier in Fusion Engineering and Design
- Vol. 81 (8) , 925-929
Exposure of reduced activation ferritic steel F82H to TEXTOR plasma
- 20 October 2005
- Published by Office of Scientific and Technical Information (OSTI)
The Role of Aspect Ratio and Beta in H-mode Confinement Scalings
The addition of high power, low aspect ratio data from the NSTX and MAST experiments have motivated a new investigation of the effect of aspect ratio on confinement scaling. Various statistical methods, including those that incorporate estimates of measurement error, have been applied to datasets constrained by the standard set of criteria in addition to the range of ? and M(sub)eff appropriate to ITER operation. Development of scalings using engineering parameters as predictor variables results in ?-scaling coefficients that range from 0.38 to 1.29; the transformation of these scalings to physics variables results in an unfavorable dependence of ?? on ?, but a favorable dependence on ?. Because the low aspect ratio devices operate at low ?(sub)T and therefore high ?(sub)T, a strong correlation exists between ? and ?, and this makes scalings based on physics variables imprecise.
- 20 October 2005
- Published by Office of Scientific and Technical Information (OSTI)
The Role of Aspect Ratio and Beta in H-mode Confinement Scalings
The addition of high power, low aspect ratio data from the NSTX and MAST experiments have motivated a new investigation of the effect of aspect ratio on confinement scaling. Various statistical methods, including those that incorporate estimates of measurement error, have been applied to datasets constrained by the standard set of criteria in addition to the range of ? and M(sub)eff appropriate to ITER operation. Development of scalings using engineering parameters as predictor variables results in ?-scaling coefficients that range from 0.38 to 1.29; the transformation of these scalings to physics variables results in an unfavorable dependence of ?? on ?, but a favorable dependence on ?. Because the low aspect ratio devices operate at low ?(sub)T and therefore high ?(sub)T, a strong correlation exists between ? and ?, and this makes scalings based on physics variables imprecise.
- 1 August 2004
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 329-333, 721-725
Investigation of compatibility of low activation ferritic steel with high performance plasma by full covering of inside vacuum vessel wall on JFT-2M
- 1 August 2004
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 329-333, 721-725
Investigation of compatibility of low activation ferritic steel with high performance plasma by full covering of inside vacuum vessel wall on JFT-2M
- 23 April 2004
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 46 (5A) , A381-A386
Coherent edge fluctuation measurements in H-mode discharges on JFT-2M
- 23 April 2004
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 46 (5A) , A381-A386
Coherent edge fluctuation measurements in H-mode discharges on JFT-2M
- 1 October 2003
- Published by IOP Publishing in Nuclear Fusion
- Vol. 43 (10) , 1288-1293
High performance tokamak experiments with a ferritic steel wall on JFT-2M
- 1 October 2003
- Published by IOP Publishing in Nuclear Fusion
- Vol. 43 (10) , 1288-1293
High performance tokamak experiments with a ferritic steel wall on JFT-2M
- 25 June 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
Advanced Material Tokamak EXperiment (AMTEX) on JFT-2M - design, fabrication, installation and conditioning of inside ferritic steel wall
On JFT-2M, to investigate whether low-activation ferritic steel (F82H) can be used as a structural material of the demonstration reactor, the Advanced Material Tokamak EXperiment (AMTEX) is being carried out step by step. The AMTEX program consists of three stages. In the 1st stage, the low-activation ferritic steel plates (FPs) were inserted between the vacuum vessel (VV) and the toroidal field coils (TFCs) to reduce the toroidal field ripple. In the 2nd stage, the pre-testing of compatibility with plasma was carried out by partially installing the FPs in the inside of VV. In the 3rd (final) stage, the testing of compatibility with plasma will be carried out by a full covering of the FPs on the inside of VV.
- 25 June 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
Advanced Material Tokamak EXperiment (AMTEX) on JFT-2M - design, fabrication, installation and conditioning of inside ferritic steel wall
On JFT-2M, to investigate whether low-activation ferritic steel (F82H) can be used as a structural material of the demonstration reactor, the Advanced Material Tokamak EXperiment (AMTEX) is being carried out step by step. The AMTEX program consists of three stages. In the 1st stage, the low-activation ferritic steel plates (FPs) were inserted between the vacuum vessel (VV) and the toroidal field coils (TFCs) to reduce the toroidal field ripple. In the 2nd stage, the pre-testing of compatibility with plasma was carried out by partially installing the FPs in the inside of VV. In the 3rd (final) stage, the testing of compatibility with plasma will be carried out by a full covering of the FPs on the inside of VV.
- Open Access
- 24 June 2003
- Published by IOP Publishing in Nuclear Fusion
- Vol. 43 (7) , 586-593
Effects of complex magnetic ripple on fast ions in JFT-2M ferritic insert experiments
In JFT-2M, ferritic steel plates (FPs) were installed on almost the whole inner surface of the vacuum vessel. This arrangement is called the ferritic inside wall (FIW), and is the third step of the advanced material tokamak experiment programme. The toroidal field (TF) ripple was reduced by optimizing the thickness of FPs but the total ripple structure has become more complex, with a non-periodic feature in the toroidal direction, because of the existence of ports and other components that limit the periodic installation of FPs. We investigated the effect of this complex ripple on the heat flux onto the first wall due to fast ion loss. The ripple trapped loss was reduced as a result of the reduced magnetic ripple of the FIW. Additional FPs were also installed outside the vacuum vessel to produce a localized larger ripple. A small ripple trapped loss was observed when the shallow ripple well exists in the poloidal cross section, and a large ripple trapped loss was observed when the ripple well extends deep into the plasma region. Experimental results were almost consistent with computation with a newly developed fully three-dimensional magnetic field orbit-following Monte-Carlo code including the three-dimensional complex structure of the TF ripple and the non-axisymmetric first wall geometry.
- 24 June 2003
- Published by IOP Publishing in Nuclear Fusion
- Vol. 43 (7) , 586-593
Open AccessEffects of complex magnetic ripple on fast ions in JFT-2M ferritic insert experiments
In JFT-2M, ferritic steel plates (FPs) were installed on almost the whole inner surface of the vacuum vessel. This arrangement is called the ferritic inside wall (FIW), and is the third step of the advanced material tokamak experiment programme. The toroidal field (TF) ripple was reduced by optimizing the thickness of FPs but the total ripple structure has become more complex, with a non-periodic feature in the toroidal direction, because of the existence of ports and other components that limit the periodic installation of FPs. We investigated the effect of this complex ripple on the heat flux onto the first wall due to fast ion loss. The ripple trapped loss was reduced as a result of the reduced magnetic ripple of the FIW. Additional FPs were also installed outside the vacuum vessel to produce a localized larger ripple. A small ripple trapped loss was observed when the shallow ripple well exists in the poloidal cross section, and a large ripple trapped loss was observed when the ripple well extends deep into the plasma region. Experimental results were almost consistent with computation with a newly developed fully three-dimensional magnetic field orbit-following Monte-Carlo code including the three-dimensional complex structure of the TF ripple and the non-axisymmetric first wall geometry.
- 31 December 2002
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 307-311, 1386-1390
Recent activities on the compatibility of the ferritic steel wall with the plasma in the JFT-2M tokamak
- 31 December 2002
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 307-311, 1386-1390
Recent activities on the compatibility of the ferritic steel wall with the plasma in the JFT-2M tokamak
- 7 August 2002
- Published by IOP Publishing in Nuclear Fusion
- Vol. 42 (8) , 1008-1013
Investigation on ripple loss reduction by ferritic steel plate insertion in JFT-2M: comparison between experimental and computational data
Ripple loss reduction resulting in reduced losses of fast ions was demonstrated successfully at the JFT-2M tokamak by installing ferritic plates between the vacuum vessel and toroidal field coils. This paper describes the comparison between the experimental results and computation based on the orbit following a Monte Carlo code. They are in qualitatively good agreement in the cases where the toroidal distribution of the toroidal field ripple is almost periodic (e.g. ferritic plate installed resulting in a complex periodic structure of the magnetic ripple), but differ in the case of toroidally small average ripple exhibiting non-periodic large local ones (e.g. ferritic plate installed resulting in a more complex non-periodic structure of the magnetic ripple).
- 7 August 2002
- Published by IOP Publishing in Nuclear Fusion
- Vol. 42 (8) , 1008-1013
Investigation on ripple loss reduction by ferritic steel plate insertion in JFT-2M: comparison between experimental and computational data
Ripple loss reduction resulting in reduced losses of fast ions was demonstrated successfully at the JFT-2M tokamak by installing ferritic plates between the vacuum vessel and toroidal field coils. This paper describes the comparison between the experimental results and computation based on the orbit following a Monte Carlo code. They are in qualitatively good agreement in the cases where the toroidal distribution of the toroidal field ripple is almost periodic (e.g. ferritic plate installed resulting in a complex periodic structure of the magnetic ripple), but differ in the case of toroidally small average ripple exhibiting non-periodic large local ones (e.g. ferritic plate installed resulting in a more complex non-periodic structure of the magnetic ripple).
- 1 January 2001
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 72 (1) , 919
Fast ion loss measurement by infrared television in reduced ripple experiment with ferritic inserts on JFT-2M (abstract)
In the medium size tokamak, JFT-2M, the ferritic steel boards (FBs) were inserted to reduce the toroidal field ripple which causes the fast ion losses. To evaluate the effect of FB insertion, two-dimensional (2D) infrared television (IRTV) system with high resolutions in time and space was developed, which is quite suitable to measure the first wall temperature increment caused by the ripple ion losses in a medium size tokamak. We adopt an IR thermal imager (Mitsubishi IR-M300) that provides a field time of 1/60 s. The detectable temperature range is 0–500 °C with resolution of 0.2 °C. The PtSi (26×20 μm) detector being sensitive to 3–5 μm IR radiation is composed of a 256×256 array. The optical system to view the first wall consists of an IR lens (f:25 mm, F:2.0), a reflecting mirror, and a sapphire vacuum window, in which distance from the camera position to the target wall is shortened to ∼3.5 m. Thus, we obtained a high spatial resolution of ∼3 mm. By using this system, the local hot spot due to the ripple trapped losses of fast ions was observed during neutral beam injection (36 kV, 500 kW) heating. The peak temperature increment ΔTs reached to ∼75 °C before FB insertion. After FB insertion, the ΔTs were reduced clearly. In the most optimized case, the temperature increment became negligibly small. These IRTV data make clear the effectiveness of FBs for reduction of fast ion losses.
- 1 January 2001
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 72 (1) , 919
Fast ion loss measurement by infrared television in reduced ripple experiment with ferritic inserts on JFT-2M (abstract)
In the medium size tokamak, JFT-2M, the ferritic steel boards (FBs) were inserted to reduce the toroidal field ripple which causes the fast ion losses. To evaluate the effect of FB insertion, two-dimensional (2D) infrared television (IRTV) system with high resolutions in time and space was developed, which is quite suitable to measure the first wall temperature increment caused by the ripple ion losses in a medium size tokamak. We adopt an IR thermal imager (Mitsubishi IR-M300) that provides a field time of 1/60 s. The detectable temperature range is 0–500 °C with resolution of 0.2 °C. The PtSi (26×20 μm) detector being sensitive to 3–5 μm IR radiation is composed of a 256×256 array. The optical system to view the first wall consists of an IR lens (f:25 mm, F:2.0), a reflecting mirror, and a sapphire vacuum window, in which distance from the camera position to the target wall is shortened to ∼3.5 m. Thus, we obtained a high spatial resolution of ∼3 mm. By using this system, the local hot spot due to the ripple trapped losses of fast ions was observed during neutral beam injection (36 kV, 500 kW) heating. The peak temperature increment ΔTs reached to ∼75 °C before FB insertion. After FB insertion, the ΔTs were reduced clearly. In the most optimized case, the temperature increment became negligibly small. These IRTV data make clear the effectiveness of FBs for reduction of fast ion losses.