Y. Pauleau
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Y. Pauleau has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
A.K. Kuleshov
Belarussian State University, 4 F.Scoriny Avenue, 220050 Minsk, Belarus
1 shared publicationF Thièry
National Polytechnic Institute of Grenoble, CNRS-UJF-LEMD, B.P. 166 25 Rue des Martyrs, 38042 Grenoble Cedex 9, France
1 shared publicationF. Thièry
Laboratoire d’Electrostatique et de Matériaux Diélectriques, CNRS, B.P. 166, 38042 Grenoble Cedex 9, France
1 shared publication- F. Thièry
National Polytechnic Institute of Grenoble CNRS-LEMD, 25 Rue des Martyrs, 38042 Grenoble cedex 9, France
1 shared publication L. Ortega
Laboratoire de Cristallographie, CNRS, B.P. 166, 38042 Grenoble Cedex 9, France
1 shared publicationM.P. Samtsov
Belarussian State University, 4 F.Scoriny Avenue, 220050 Minsk, Belarus
1 shared publication
Latest Publications
- 1 March 2004
- Published by Elsevier in Surface and Coatings Technology
- Vol. 180-181, 102-107
Tribological properties of copper/carbon films formed by microwave plasma-assisted deposition techniques
- 1 March 2004
- Published by Elsevier in Surface and Coatings Technology
- Vol. 180-181, 102-107
Tribological properties of copper/carbon films formed by microwave plasma-assisted deposition techniques
- 13 November 2003
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 22 (1) , 30-35
Effect of the substrate bias voltage on the physical characteristics of copper films deposited by microwave plasma-assisted sputtering technique
Pure copper films have been deposited by microwave plasma-assisted sputtering on (100)-oriented single crystal silicon substrates mounted on a water-cooled substrate holder either maintained at the floating potential or biased to various dc voltages ranging from 0 to −125 V. The argon pressure was fixed at 0.13 Pa and argon ions from the discharge produced in a distributed electron cyclotron resonance microwave plasma chamber were used for sputtering of a copper target biased to −600 V. The crystallographic structure and surface morphology of copper films were determined by x-ray diffraction techniques and atomic force microscopy, respectively. The magnitude of residual stresses developed in these films was calculated from the radius of curvature of Si substrates. The electrical resistivity of films was deduced from the thickness and sheet resistance of films determined by profilometry and four point probe measurements. The evolution of the deposition rate, surface roughness, microstructure, magnitude of residual stresses, and electrical resistivity of films was investigated as a function of the substrate bias voltage. The major characteristics of copper films were found to vary significantly as the negative substrate bias voltage increased from −40 to −125 V or with increasing argon ion energy. The resputtering process of a fraction of copper atoms by energetic incident argon ions was responsible for the modification of characteristics of films deposited on biased substrates. The quality of copper films in terms of surface morphology and electrical resistivity in particular was found to be excellent for incident argon ion energy values lower than 70 eV.
- 13 November 2003
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 22 (1) , 30-35
Effect of the substrate bias voltage on the physical characteristics of copper films deposited by microwave plasma-assisted sputtering technique
Pure copper films have been deposited by microwave plasma-assisted sputtering on (100)-oriented single crystal silicon substrates mounted on a water-cooled substrate holder either maintained at the floating potential or biased to various dc voltages ranging from 0 to −125 V. The argon pressure was fixed at 0.13 Pa and argon ions from the discharge produced in a distributed electron cyclotron resonance microwave plasma chamber were used for sputtering of a copper target biased to −600 V. The crystallographic structure and surface morphology of copper films were determined by x-ray diffraction techniques and atomic force microscopy, respectively. The magnitude of residual stresses developed in these films was calculated from the radius of curvature of Si substrates. The electrical resistivity of films was deduced from the thickness and sheet resistance of films determined by profilometry and four point probe measurements. The evolution of the deposition rate, surface roughness, microstructure, magnitude of residual stresses, and electrical resistivity of films was investigated as a function of the substrate bias voltage. The major characteristics of copper films were found to vary significantly as the negative substrate bias voltage increased from −40 to −125 V or with increasing argon ion energy. The resputtering process of a fraction of copper atoms by energetic incident argon ions was responsible for the modification of characteristics of films deposited on biased substrates. The quality of copper films in terms of surface morphology and electrical resistivity in particular was found to be excellent for incident argon ion energy values lower than 70 eV.
- 30 November 2002
- Published by Elsevier in Materials Letters
- Vol. 56 (6) , 1053-1058
Nanostructured copper–carbon composite thin films produced by sputter deposition/microwave plasma-enhanced chemical vapor deposition dual process
- 30 November 2002
- Published by Elsevier in Materials Letters
- Vol. 56 (6) , 1053-1058
Nanostructured copper–carbon composite thin films produced by sputter deposition/microwave plasma-enhanced chemical vapor deposition dual process