Li Hou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Li Hou has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Qi Zhang
School of Intelligent Manufacturing, Panzhihua University, Panzhihua, Sichuan, China
1 shared publication- Song Leng
School of Mechanical Engineering, Sichuan University, Chengdu, China
1 shared publication - Xin Sheng
School of Mechanical Engineering Sichuan University No. 24 South Section 1, Yihuan Road Chengdu 610065 China
1 shared publication - Yang Duan
College of Mechanical Engineering, Sichuan University, Chengdu 610065, China
1 shared publication Yang Wu
School of Mechanical Engineering, Sichuan University, Chengdu, Sichuan, China
1 shared publicationYunxia You
China Aerodynamics Research and Development Center, Aerospace Technology Institute, Mianyang, Sichuan, China
1 shared publication
Latest Publications
- 14 October 2022
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 45 (8) , 713-723
Multi-objective optimization of the geometric parameters of a pressure-swirl nozzle
The geometric parameters of the pressure-swirl nozzle demonstrate a significant effect on the atomization performance such as the spray cone angle and mass flow rate. However, these objectives are incompatible, and obtaining a nozzle geometric parameter that optimizes all the atomization performances is difficult. The effectiveness of the nozzle optimization process is typically low, resulting in high costs. To this purpose, an enhanced CBSO-Kriging surrogate model was developed to solve this expensive black box problem, and the spray cone angle and mass flow rate were optimized using a multi-objective optimization algorithm. Firstly, the optimal Latin hypercube sampling method was used to generate 65 sets of sample points, and the corresponding response values were calculated using CFD simulation. The established surrogate model of atomization performance can predict the atomization characteristics of the nozzle with arbitrary shape. The correlation between the key geometric parameters and the spray cone angle and the mass flow rate was determined on this basis. Then, to find the optimal geometric parameters for the nozzle, the NSGA-II algorithm was used. In comparison to the initial model, the optimization results show that the spray cone angle and mass flow rate increased by 4.26% and 37.74%, respectively.
- 14 October 2022
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 45 (8) , 713-723
Multi-objective optimization of the geometric parameters of a pressure-swirl nozzle
The geometric parameters of the pressure-swirl nozzle demonstrate a significant effect on the atomization performance such as the spray cone angle and mass flow rate. However, these objectives are incompatible, and obtaining a nozzle geometric parameter that optimizes all the atomization performances is difficult. The effectiveness of the nozzle optimization process is typically low, resulting in high costs. To this purpose, an enhanced CBSO-Kriging surrogate model was developed to solve this expensive black box problem, and the spray cone angle and mass flow rate were optimized using a multi-objective optimization algorithm. Firstly, the optimal Latin hypercube sampling method was used to generate 65 sets of sample points, and the corresponding response values were calculated using CFD simulation. The established surrogate model of atomization performance can predict the atomization characteristics of the nozzle with arbitrary shape. The correlation between the key geometric parameters and the spray cone angle and the mass flow rate was determined on this basis. Then, to find the optimal geometric parameters for the nozzle, the NSGA-II algorithm was used. In comparison to the initial model, the optimization results show that the spray cone angle and mass flow rate increased by 4.26% and 37.74%, respectively.
- 14 January 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 112 (11-12) , 3201-3214
A novel cutting tool selection approach based on a metal cutting process knowledge graph
- 14 January 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 112 (11-12) , 3201-3214
A novel cutting tool selection approach based on a metal cutting process knowledge graph
- 1 January 2021
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 57 (3) , 77-86
Modular Design for Machine Tools of Variable Hyperbolic Circular-arc-tooth-trace Cylindrical Gear
- 1 January 2021
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 57 (3) , 77-86
Modular Design for Machine Tools of Variable Hyperbolic Circular-arc-tooth-trace Cylindrical Gear