Ignacijo Biluš
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ignacijo Biluš has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Andrej Predin
Faculty of Energy Technology, University of Maribor, Hočevarjev trg 1, 8270 Krško, Slovenia
2 shared publications - L. Škerget
Faculty of Mechanical Engineering, University of Maribor, Smetanova 17, SI-2000 Maribor, Slovenia
1 shared publication - Primož Ternik
Ternik Primož - Zasebni raziskovalec, Bresterniška ulica 163, Bresternica, Slovenia
1 shared publication Zoran Žunič
AVL-AST D.O.O., Trg Leona Štuklja 5, 2000 Maribor, Slovenia
1 shared publication
Latest Publications
- 30 November 2011
- Published by Elsevier in Journal of Fluids and Structures
- Vol. 27 (8) , 1278-1295
Further contributions on the flow past a stationary and confined cylinder: Creeping and slowly moving flow of Power law fluids
- 30 November 2011
- Published by Elsevier in Journal of Fluids and Structures
- Vol. 27 (8) , 1278-1295
Further contributions on the flow past a stationary and confined cylinder: Creeping and slowly moving flow of Power law fluids
- 1 January 2007
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 45 (1) , 81-87
The extended homogenous cavitation transport model
Cavitating flows are complex three dimensional flows with phase change in the low pressure regions. These are very sensitive to bubbles formation process and to velocity/pressure pulsations caused by turbulence. The presented cavitation model derived from a reduced Rayleigh–Plesset equation accounts for some of these effects. This model is based on the additional generic transport equation for vapour phase. The cavitation influence over the mixture density and viscosity is included in the model, which is implemented in commercial, general purpose Computational Fluid Dynamics code and validated on practical flow examples
- 1 January 2007
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 45 (1) , 81-87
The extended homogenous cavitation transport model
Cavitating flows are complex three dimensional flows with phase change in the low pressure regions. These are very sensitive to bubbles formation process and to velocity/pressure pulsations caused by turbulence. The presented cavitation model derived from a reduced Rayleigh–Plesset equation accounts for some of these effects. This model is based on the additional generic transport equation for vapour phase. The cavitation influence over the mixture density and viscosity is included in the model, which is implemented in commercial, general purpose Computational Fluid Dynamics code and validated on practical flow examples
- 1 March 2003
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 41 (2) , 207-216
Influence of additional inlet flow on the prerotation and performance of centrifugal impellers
In this paper we present the results of our experimental analysis regarding the influence of additional flow when added at the radial impeller entrance eye. This analysis was done on both operating and prerotation flow characteristics. The experimental system tested was arranged to operate using air. The additional flow adding system (AFAS) was placed at the entrance eye of the impeller through the guide system, which consists of the spiral volute at the entrance, ring guide pipe (where the guide vanes are placed), and a ring - like hollow at the end of the AFAS. The ring - like hollow was placed near the shroud at the entrance edge of the impeller blades. The guide vanes in the AFAS were placed in the axial direction, so that the added flow had no swirl component. The operating regime was tested, whereby the AFAS was filled by the flow under atmospheric pressure (non-forced loading). A good influence was evident on the operating characteristic. The stable operating range was enlarged and the operating noise decreased. The achieved impeller head and the overall efficiency increased.
- 1 March 2003
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 41 (2) , 207-216
Influence of additional inlet flow on the prerotation and performance of centrifugal impellers
In this paper we present the results of our experimental analysis regarding the influence of additional flow when added at the radial impeller entrance eye. This analysis was done on both operating and prerotation flow characteristics. The experimental system tested was arranged to operate using air. The additional flow adding system (AFAS) was placed at the entrance eye of the impeller through the guide system, which consists of the spiral volute at the entrance, ring guide pipe (where the guide vanes are placed), and a ring - like hollow at the end of the AFAS. The ring - like hollow was placed near the shroud at the entrance edge of the impeller blades. The guide vanes in the AFAS were placed in the axial direction, so that the added flow had no swirl component. The operating regime was tested, whereby the AFAS was filled by the flow under atmospheric pressure (non-forced loading). A good influence was evident on the operating characteristic. The stable operating range was enlarged and the operating noise decreased. The achieved impeller head and the overall efficiency increased.