Amir Hosseini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Amir Hosseini has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Ray T. Chen
Department of Electrical and Computer Engineering, The University of Texas at Austin, Austin, USA
7 shared publications - David Kwong
University of Texas at Austin, Austin, TX, USA
3 shared publications Ray T. Chen
The Univ. of Texas at Austin (United States)
3 shared publications- Xiaochuan Xu
Harbin Institute of Technology
3 shared publications - Xiaohui Lin
The Univ. of Texas at Austin (United States)
3 shared publications - Harish Subbaraman
Omega Optics, Inc. (United States)
2 shared publications
Latest Publications
- 10 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 26 (23) , 2376-2379
0.88-THz Optical Clock Distribution on Adhesively Bonded Silicon Nanomembrane
Silicon photonics is a promising solution for on-chip optical clock distribution. We developed an adhesive bonding process to integrate silicon nanomembranes onto silicon chips. The single-mode strip waveguide fabricated on this adhesively bonded silicon membrane has a propagation loss of 4.3 dB/cm. A grating-coupled 1-to-32 H-tree optical distribution is experimentally demonstrated. Each branch includes 1.1-cm long strip waveguides, five Y-splitters, and three 90° bends. This optical distribution has a insertion loss of 13.9 dB, uniformity of 0.72 dB, and 3-dB bandwidth of 880 GHz determined by optical autocorrelation.
- 10 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 26 (23) , 2376-2379
0.88-THz Optical Clock Distribution on Adhesively Bonded Silicon Nanomembrane
Silicon photonics is a promising solution for on-chip optical clock distribution. We developed an adhesive bonding process to integrate silicon nanomembranes onto silicon chips. The single-mode strip waveguide fabricated on this adhesively bonded silicon membrane has a propagation loss of 4.3 dB/cm. A grating-coupled 1-to-32 H-tree optical distribution is experimentally demonstrated. Each branch includes 1.1-cm long strip waveguides, five Y-splitters, and three 90° bends. This optical distribution has a insertion loss of 13.9 dB, uniformity of 0.72 dB, and 3-dB bandwidth of 880 GHz determined by optical autocorrelation.
- Open Access
Wide optical spectrum range, sub-volt, compact modulator based on electro-optic polymer refilled silicon slot photonic crystal waveguide
We design and demonstrate a compact and low-power band-engineered electro-optic (EO) polymer refilled silicon slot photonic crystal waveguide (PCW) modulator. The EO polymer is engineered for large EO activity and near-infrared transparency. A PCW step coupler is used for optimum coupling to the slow-light mode of the band-engineered PCW. The half-wave switching-voltage is measured to be V{\pi}=0.97+-0.02V over optical spectrum range of 8nm, corresponding to the effective in-device r33 of 1190pm/V and V{\pi} L of 0.291+-0.006V mm in a push-pull configuration. Excluding the slow-light effect, we estimate the EO polymer is poled with an efficiency of 89pm/V in the slot.
Open AccessWide optical spectrum range, sub-volt, compact modulator based on electro-optic polymer refilled silicon slot photonic crystal waveguide
We design and demonstrate a compact and low-power band-engineered electro-optic (EO) polymer refilled silicon slot photonic crystal waveguide (PCW) modulator. The EO polymer is engineered for large EO activity and near-infrared transparency. A PCW step coupler is used for optimum coupling to the slow-light mode of the band-engineered PCW. The half-wave switching-voltage is measured to be V{\pi}=0.97+-0.02V over optical spectrum range of 8nm, corresponding to the effective in-device r33 of 1190pm/V and V{\pi} L of 0.291+-0.006V mm in a push-pull configuration. Excluding the slow-light effect, we estimate the EO polymer is poled with an efficiency of 89pm/V in the slot.
- 20 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 20 (4) , 171-180
Cavity-Waveguide Coupling Engineered High Sensitivity Silicon Photonic Crystal Microcavity Biosensors With High Yield
We present a high yield and high sensitivity on-chip biosensing system by combining subwavelength grating coupling and high sensitivity photonic crystal microcavity side coupled to a photonic crystal waveguide. 80% yield of working devices was experimentally demonstrated for sensitivity engineered L13 photonic crystal microcavities and 70% for L21 photonic crystal microcavities. Subwavelength grating couplers significantly improved the quality of the output transmission spectrum. By engineering the optical loss rate from the cavity to the waveguide, we experimentally detected 1 pM (67 pg/ml) and 50 femto-molar (3.35 pg/ml) concentration of avidin binding to biotin in phosphate buffered saline for L21 and L55 PC microcavities respectively, which represents the highest sensitivity versus other chip-based optical biosensors.
- 20 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 20 (4) , 171-180
Cavity-Waveguide Coupling Engineered High Sensitivity Silicon Photonic Crystal Microcavity Biosensors With High Yield
We present a high yield and high sensitivity on-chip biosensing system by combining subwavelength grating coupling and high sensitivity photonic crystal microcavity side coupled to a photonic crystal waveguide. 80% yield of working devices was experimentally demonstrated for sensitivity engineered L13 photonic crystal microcavities and 70% for L21 photonic crystal microcavities. Subwavelength grating couplers significantly improved the quality of the output transmission spectrum. By engineering the optical loss rate from the cavity to the waveguide, we experimentally detected 1 pM (67 pg/ml) and 50 femto-molar (3.35 pg/ml) concentration of avidin binding to biotin in phosphate buffered saline for L21 and L55 PC microcavities respectively, which represents the highest sensitivity versus other chip-based optical biosensors.
- 15 November 2013
- Published by Optica Publishing Group in Optics Letters
- Vol. 38 (22) , 4931-4934
Wide optical spectrum range, subvolt, compact modulator based on an electro-optic polymer refilled silicon slot photonic crystal waveguide
We design and demonstrate a compact and low-power, band-engineered, electro-optic (EO) polymer refilled silicon slot photonic crystal waveguide (PCW) modulator. The EO polymer is engineered for large EO activity and near-infrared transparency. A PCW step coupler is used for optimum coupling to the slow-light mode of the band-engineered PCW. The half-wave switching voltage is measured to be over an optical spectrum range of 8 nm, corresponding to the effective in-device of and in a push–pull configuration. Excluding the slow-light effect, we estimate that the EO polymer is poled with an efficiency of in the slot.- 15 November 2013
- Published by Optica Publishing Group in Optics Letters
- Vol. 38 (22) , 4931-4934
Wide optical spectrum range, subvolt, compact modulator based on an electro-optic polymer refilled silicon slot photonic crystal waveguide
We design and demonstrate a compact and low-power, band-engineered, electro-optic (EO) polymer refilled silicon slot photonic crystal waveguide (PCW) modulator. The EO polymer is engineered for large EO activity and near-infrared transparency. A PCW step coupler is used for optimum coupling to the slow-light mode of the band-engineered PCW. The half-wave switching voltage is measured to be over an optical spectrum range of 8 nm, corresponding to the effective in-device of and in a push–pull configuration. Excluding the slow-light effect, we estimate that the EO polymer is poled with an efficiency of in the slot.- 10 September 2013
- Published by Optica Publishing Group in Optics Letters
- Vol. 38 (18) , 3608-3611
Ultralow-loss silicon waveguide crossing using Bloch modes in index-engineered cascaded multimode-interference couplers
We investigate the loss mechanism in three-moded multimode-interference couplers that are the building blocks of a compact and low-loss waveguide crossing structure. Broadband silicon waveguide crossing arrays with insertion loss per crossing are proposed using cascaded multimode-interference couplers, where lateral subwavelength nanostructures are used to reduce the insertions loss. We design and fabricate a waveguide crossing array with a pitch of 3.08 μm. Insertion loss of per crossing and crosstalk at 1550 nm operating wavelength and a broad transmission spectrum ranging from 1520 to 1610 nm are experimentally demonstrated.- 10 September 2013
- Published by Optica Publishing Group in Optics Letters
- Vol. 38 (18) , 3608-3611
Ultralow-loss silicon waveguide crossing using Bloch modes in index-engineered cascaded multimode-interference couplers
We investigate the loss mechanism in three-moded multimode-interference couplers that are the building blocks of a compact and low-loss waveguide crossing structure. Broadband silicon waveguide crossing arrays with insertion loss per crossing are proposed using cascaded multimode-interference couplers, where lateral subwavelength nanostructures are used to reduce the insertions loss. We design and fabricate a waveguide crossing array with a pitch of 3.08 μm. Insertion loss of per crossing and crosstalk at 1550 nm operating wavelength and a broad transmission spectrum ranging from 1520 to 1610 nm are experimentally demonstrated.- 27 February 2013
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8630
Board-to-board optical interconnects utilizing molded embedded 45 degree mirrors and print-on-demand micro-lenses as proximity vertical coupler
We demonstrate board-to-board optical communication utilizing 45 degree mirrors and print-on-demand micro-lenses as surface-normal coupler. The presented system which includes polymer waveguides, embedded 45 degree mirrors and micro-lenses, realizes back-to-back optical interconnects between two boards. The waveguide and mirrors are fabricated using molding method using a low-cost electroplated nickel mold. Micro-lenses (80 μm in diameter) are fabricated using a material inkjet-printer, on top of the 45 degree mirrors. Experimental results show that each 45 degree mirror contributes about 1.88 dB loss (65% coupling efficiency) to the total optical loss. When propagating in free space without a lens, a 2 mm separation between boards results in a 9.9 dB loss, which is reduced to 7.5 dB when a micro-lens is inserted in the path. High speed data transmission test is performed at various separations. At a separation of 1mm, the system can provide 10Gbps error free transmission. At 2mm separation, the maximum error free data rate was measured to be 3.5Gbps and 7.5Gbps, with and without the micro-lens, respectively. Printing the micro-lenses on both the input 45 degree mirror and the photodiode or the receiving 45 degree mirror in a confocal setup will significantly reduce the freespace propagation loss. To the best of our knowledge, this is the first report of free-space coupling between waveguides on separate boards.
- 27 February 2013
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8630
Board-to-board optical interconnects utilizing molded embedded 45 degree mirrors and print-on-demand micro-lenses as proximity vertical coupler
We demonstrate board-to-board optical communication utilizing 45 degree mirrors and print-on-demand micro-lenses as surface-normal coupler. The presented system which includes polymer waveguides, embedded 45 degree mirrors and micro-lenses, realizes back-to-back optical interconnects between two boards. The waveguide and mirrors are fabricated using molding method using a low-cost electroplated nickel mold. Micro-lenses (80 μm in diameter) are fabricated using a material inkjet-printer, on top of the 45 degree mirrors. Experimental results show that each 45 degree mirror contributes about 1.88 dB loss (65% coupling efficiency) to the total optical loss. When propagating in free space without a lens, a 2 mm separation between boards results in a 9.9 dB loss, which is reduced to 7.5 dB when a micro-lens is inserted in the path. High speed data transmission test is performed at various separations. At a separation of 1mm, the system can provide 10Gbps error free transmission. At 2mm separation, the maximum error free data rate was measured to be 3.5Gbps and 7.5Gbps, with and without the micro-lens, respectively. Printing the micro-lenses on both the input 45 degree mirror and the photodiode or the receiving 45 degree mirror in a confocal setup will significantly reduce the freespace propagation loss. To the best of our knowledge, this is the first report of free-space coupling between waveguides on separate boards.
- 16 May 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (11) , 12318-12325
Large optical spectral range dispersion engineered silicon-based photonic crystal waveguide modulator
We present a dispersion engineered slow light silicon-based photonic crystal waveguide PIN modulator. Low-dispersion slow light transmission over 18nm bandwidth under the silica light line with a group index of 26.5 is experimentally confirmed. We investigate the variations of the modulator figure of merit, Vπ × L, as a function of the optical carrier wavelength over the bandwidth of the fundamental photonic crystal waveguide defect mode. A large signal operation with a record low maximum Vπ × L of 0.0464 V⋅mm over the low-dispersion optical spectral range is demonstrated. We also report the device operation at 2GHz.
- 16 May 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (11) , 12318-12325
Large optical spectral range dispersion engineered silicon-based photonic crystal waveguide modulator
We present a dispersion engineered slow light silicon-based photonic crystal waveguide PIN modulator. Low-dispersion slow light transmission over 18nm bandwidth under the silica light line with a group index of 26.5 is experimentally confirmed. We investigate the variations of the modulator figure of merit, Vπ × L, as a function of the optical carrier wavelength over the bandwidth of the fundamental photonic crystal waveguide defect mode. A large signal operation with a record low maximum Vπ × L of 0.0464 V⋅mm over the low-dispersion optical spectral range is demonstrated. We also report the device operation at 2GHz.
- 12 October 2011
- Published by Optica Publishing Group in Optics Letters
- Vol. 36 (20) , 4047-4049
Ultracompact and fabrication-tolerant integrated polarization splitter
Design and fabrication of a two-mode interference (TMI) coupler based on-chip polarization splitter is presented. By changing the angle between the access waveguides, one can tune the effective TMI length for the mode with less optical confinement (transverse magnetic, TM) to coincide with the target TMI length for a desired transmission of the mode with higher optical confinement (transverse electric, TE). The fabricated long TMI splits the input power into TM (bar) and TE (cross) outputs with splitting ratio over over bandwidth. Fabrication tolerance analysis shows that the device is tolerant to fabrication errors as large as .- 12 October 2011
- Published by Optica Publishing Group in Optics Letters
- Vol. 36 (20) , 4047-4049
Ultracompact and fabrication-tolerant integrated polarization splitter
Design and fabrication of a two-mode interference (TMI) coupler based on-chip polarization splitter is presented. By changing the angle between the access waveguides, one can tune the effective TMI length for the mode with less optical confinement (transverse magnetic, TM) to coincide with the target TMI length for a desired transmission of the mode with higher optical confinement (transverse electric, TE). The fabricated long TMI splits the input power into TM (bar) and TE (cross) outputs with splitting ratio over over bandwidth. Fabrication tolerance analysis shows that the device is tolerant to fabrication errors as large as .- 10 February 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7944, 79440F
Transfer and characterization of silicon nanomembrane-based photonic devices on flexible polyimide substrate
In this paper, we report the transfer and characterization of in-plane silicon nanomembrane based photonic devices on a Kapton polyimide flexible substrate. Compared with electronic devices and surface normal optical devices, in-plane photonic devices have stringent requirements on transfer precision because any shift in the position or breakage can affect the performance of devices. Therefore, a supporting layer consisting of a photoresist is exploited to protect the device during the transfer process. A modified stamp-assisted transfer technique is employed in order to transfer nanomembrane devices onto the flexible film and the transfer of large aspect ratio (up to 4000) waveguides and 1x6 multimode interference (MMI) couplers on a flexible Kapton substrate is demonstrated. A two-step cleaving method is developed in order to prepare the facets of the transferred waveguides and in-plane light coupling into a 60μm wide, 8mm long flexible waveguide from a lensed fiber is demonstrated. This demonstration opens limitless possibilities for a whole new area of high performance flexible photonic components using silicon nanomembrane technology.
- 10 February 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7944, 79440F
Transfer and characterization of silicon nanomembrane-based photonic devices on flexible polyimide substrate
In this paper, we report the transfer and characterization of in-plane silicon nanomembrane based photonic devices on a Kapton polyimide flexible substrate. Compared with electronic devices and surface normal optical devices, in-plane photonic devices have stringent requirements on transfer precision because any shift in the position or breakage can affect the performance of devices. Therefore, a supporting layer consisting of a photoresist is exploited to protect the device during the transfer process. A modified stamp-assisted transfer technique is employed in order to transfer nanomembrane devices onto the flexible film and the transfer of large aspect ratio (up to 4000) waveguides and 1x6 multimode interference (MMI) couplers on a flexible Kapton substrate is demonstrated. A two-step cleaving method is developed in order to prepare the facets of the transferred waveguides and in-plane light coupling into a 60μm wide, 8mm long flexible waveguide from a lensed fiber is demonstrated. This demonstration opens limitless possibilities for a whole new area of high performance flexible photonic components using silicon nanomembrane technology.
- 23 June 2010
- Published by IOP Publishing in Journal of Optics
- Vol. 12 (7)
Tapered multi-mode interference couplers for high order mode power extraction
- 23 June 2010
- Published by IOP Publishing in Journal of Optics
- Vol. 12 (7)
Tapered multi-mode interference couplers for high order mode power extraction