Shigeharu Morooka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shigeharu Morooka has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Katsuki Kusakabe
Department of Applied Chemistry, Kyushu University
4 shared publications Hideaki Maeda
3 shared publicationsTakeyasu Saito
2 shared publicationsYoshikazu Yamasaki
Department of Chemical Engineering, Fukuoka University, Fukuoka, Japan
2 shared publicationsAkiharu Ousaka
University of Tokushima, Tokushima, Japan
1 shared publicationAkira Kariyasaki
Fukuoka University, Fukuoka, Japan
1 shared publication
Latest Publications
- 2 October 2015
- Published by Wiley in Chemical Engineering & Technology
- Vol. 38 (11) , 1965-1971
Bubble Mobilization Pressure in a Small-Diameter Tube
- 2 October 2015
- Published by Wiley in Chemical Engineering & Technology
- Vol. 38 (11) , 1965-1971
Bubble Mobilization Pressure in a Small-Diameter Tube
- 27 September 2010
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 8 (1)
Hydrophilic and Hydrophobic Modifications of Microchannel Inner Walls for Liquid-Liquid Laminar Layered Flows
Microchannels, which have a wide surface area per unit volume, have the potential for use in efficient chemical synthesis, separation and analysis. When microchannels are applied to mass transfer operations between immiscible liquids, a layered laminar flow is preferable because the two liquids can be spontaneously separated at the outlets. In this study, the flow of a water-octane system in a horizontal microchannel 200 ?m in width and 200 ?m in depth was simulated using CFD software. The simulation suggested that a stable layered flow was realized when the contact angle of octane on the hydrophobic inner walls was smaller than ca. 60 degrees and when that on the hydrophilic inner walls was larger than ca. 120 degrees irrespective of the inlet planes into which water and octane were introduced. To fulfill these requirements, PMMA plates were modified using five procedures, and the contact angles of one of the liquids were determined in the presence of the counterpart liquid. Measurement of the contact angles was carried out by lateral observation (in the case of spherical cap drops) and the fringe pattern of laser interference (in the case of thin films). When the two liquids coexisted, a combination of modification with 1-octadecanethiol for hydrophobicity and coating with TiO2 for hydrophilicity was the most workable of the treatments tested. Microchannels modified by this combination were then fabricated. When either water or octane were introduced into the hydrophilic and hydrophobic half-sections, respectively, a stable two-phase layered flow was obtained.
- 27 September 2010
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 8 (1)
Hydrophilic and Hydrophobic Modifications of Microchannel Inner Walls for Liquid-Liquid Laminar Layered Flows
Microchannels, which have a wide surface area per unit volume, have the potential for use in efficient chemical synthesis, separation and analysis. When microchannels are applied to mass transfer operations between immiscible liquids, a layered laminar flow is preferable because the two liquids can be spontaneously separated at the outlets. In this study, the flow of a water-octane system in a horizontal microchannel 200 ?m in width and 200 ?m in depth was simulated using CFD software. The simulation suggested that a stable layered flow was realized when the contact angle of octane on the hydrophobic inner walls was smaller than ca. 60 degrees and when that on the hydrophilic inner walls was larger than ca. 120 degrees irrespective of the inlet planes into which water and octane were introduced. To fulfill these requirements, PMMA plates were modified using five procedures, and the contact angles of one of the liquids were determined in the presence of the counterpart liquid. Measurement of the contact angles was carried out by lateral observation (in the case of spherical cap drops) and the fringe pattern of laser interference (in the case of thin films). When the two liquids coexisted, a combination of modification with 1-octadecanethiol for hydrophobicity and coating with TiO2 for hydrophilicity was the most workable of the treatments tested. Microchannels modified by this combination were then fabricated. When either water or octane were introduced into the hydrophilic and hydrophobic half-sections, respectively, a stable two-phase layered flow was obtained.
- 1 January 2005
- Published by ASME International
- p. 585-589
Separation of Air From Two-Phase Air-Water Mixture Flowing in a Mini Channel
An air-water separator which uses the centrifugal force as a driving force was developed and tested for micro scale flow systems. The device is composed of a main-channel of return bend, a sub-channel running along the main-channel, and several connecting-channels which connect the main- and the sub-channel. When two-phase mixture flows through the curved main-channel, water drifts towards outside region of the curvature and partly into the sub-channel. Consequently air holdup in main-channel becomes large at its exit. The performance of the device was evaluated numerically and experimentally by means of water recovery, air recovery, and Newton efficiency.
- 1 January 2005
- Published by ASME International
- p. 585-589
Separation of Air From Two-Phase Air-Water Mixture Flowing in a Mini Channel
An air-water separator which uses the centrifugal force as a driving force was developed and tested for micro scale flow systems. The device is composed of a main-channel of return bend, a sub-channel running along the main-channel, and several connecting-channels which connect the main- and the sub-channel. When two-phase mixture flows through the curved main-channel, water drifts towards outside region of the curvature and partly into the sub-channel. Consequently air holdup in main-channel becomes large at its exit. The performance of the device was evaluated numerically and experimentally by means of water recovery, air recovery, and Newton efficiency.
- 1 January 2001
- Published by Taylor & Francis in JOURNAL OF CHEMICAL ENGINEERING OF JAPAN
- Vol. 34 (5) , 703-705
Preparation of Thin Palladium Membranes by a Novel Method Based on Photolithography and Electrolysis.
A negative resist was spin-coated on the surface of a 50-μm thick copper film, and was solidified as a protection film. A palladium layer was then electrodeposited on the other uncovered surface. After removing the protection film, the resist was again spin-coated on the copper surface, and a pattern of microslits was transferred by photolithography. After development, the microslits were electrolytically etched out. Thus a palladium membrane of 5 mm in diameter was formed as an assemblage of thin layers formed in the microslits. The palladium membranes prepared were characterized by SEM observation, as well as by permeation measurements for hydrogen and nitrogen at 573-873 K. The palladium membrane, which was 3 μm in thickness and formed on a polished copper film, showed separation factor of hydrogen to nitrogen of 120 at 873 K.
- 1 January 2001
- Published by Taylor & Francis in JOURNAL OF CHEMICAL ENGINEERING OF JAPAN
- Vol. 34 (5) , 703-705
Preparation of Thin Palladium Membranes by a Novel Method Based on Photolithography and Electrolysis.
A negative resist was spin-coated on the surface of a 50-μm thick copper film, and was solidified as a protection film. A palladium layer was then electrodeposited on the other uncovered surface. After removing the protection film, the resist was again spin-coated on the copper surface, and a pattern of microslits was transferred by photolithography. After development, the microslits were electrolytically etched out. Thus a palladium membrane of 5 mm in diameter was formed as an assemblage of thin layers formed in the microslits. The palladium membranes prepared were characterized by SEM observation, as well as by permeation measurements for hydrogen and nitrogen at 573-873 K. The palladium membrane, which was 3 μm in thickness and formed on a polished copper film, showed separation factor of hydrogen to nitrogen of 120 at 873 K.
- 1 January 1998
- Published by Royal Society of Chemistry (RSC) in Journal of the Chemical Society, Faraday Transactions
- Vol. 94 (7) , 929-932
Incorporation of butyl groups into chlorinated diamond surface carbons by organic reactions at ambient temperature
Hydrogenated diamond powder has been chlorinated by a radical reaction using sulfuryl chloride in chloroform at 50°C. The chlorinated diamond was then treated with n-, sec- and tert-butyllithium in tetrahydrofuran at 30°C for 4 h, and butyl groups were incorporated onto the surface. The modified diamond powder was characterized by diffuse reflectance IR Fourier-transformed (DRIFT) spectroscopy. The surface substituents were decomposed by flash pyrolysis in a nitrogen flow at temperatures between 255 and 1040°C and essentially all organic fragments were recovered. When the pyrolysis temperature was increased, the total amount of recovered carbons gradually approached a constant value. The fraction of butylated surface carbons to the total surface carbons was calculated based on pyrolysis products obtained at 1040°C and was 0.055 for n-butylation, 0.040 for sec-butylation and 0.047 for tert-butylation.
- 1 January 1998
- Published by Royal Society of Chemistry (RSC) in Journal of the Chemical Society, Faraday Transactions
- Vol. 94 (7) , 929-932
Incorporation of butyl groups into chlorinated diamond surface carbons by organic reactions at ambient temperature
Hydrogenated diamond powder has been chlorinated by a radical reaction using sulfuryl chloride in chloroform at 50°C. The chlorinated diamond was then treated with n-, sec- and tert-butyllithium in tetrahydrofuran at 30°C for 4 h, and butyl groups were incorporated onto the surface. The modified diamond powder was characterized by diffuse reflectance IR Fourier-transformed (DRIFT) spectroscopy. The surface substituents were decomposed by flash pyrolysis in a nitrogen flow at temperatures between 255 and 1040°C and essentially all organic fragments were recovered. When the pyrolysis temperature was increased, the total amount of recovered carbons gradually approached a constant value. The fraction of butylated surface carbons to the total surface carbons was calculated based on pyrolysis products obtained at 1040°C and was 0.055 for n-butylation, 0.040 for sec-butylation and 0.047 for tert-butylation.
- 1 January 1997
- Published by The Surface Finishing Society of Japan in Journal of The Surface Finishing Society of Japan
- Vol. 48 (1) , 8-13
Synthesis of Highly Oriented Diamond Film and Control of Its Surface Morphology.
総合学術電子ジャーナルサイト「J-STAGE」-国内で発行された学術論文全文を読むことのできる、日本最大級の総合電子ジャーナルプラットフォームです。
- 1 January 1997
- Published by The Surface Finishing Society of Japan in Journal of The Surface Finishing Society of Japan
- Vol. 48 (1) , 8-13
Synthesis of Highly Oriented Diamond Film and Control of Its Surface Morphology.
総合学術電子ジャーナルサイト「J-STAGE」-国内で発行された学術論文全文を読むことのできる、日本最大級の総合電子ジャーナルプラットフォームです。
- 1 January 1994
- Published by The Membrane Society of Japan in MEMBRANE
- Vol. 19 (3) , 165-170
Preparation of Inorganic Membranes by Sol-gel Method for Gas Separation.
Development of sol-gel derived porous ceramic membrane is reviewed from the standpoint of gas separation at high temperature. Amorphous silica membranes have attained both high hydrogen selectivity and permeability. However, γ-alumina membranes coated by Yoldas method have pores of 2-10 nm in size, and their hydrogen selectivity is relatively low due to the Knudsen diffusion mechanism. Modification of pores by impregnation of ultrafine particles or chemical vapor deposition improves the selectivity by the size of molecules. The interaction of molecules with pore walls is important for the separation of polar gases. Multicomponent oxide membranes are thermally and chemically stable at high temperature and have appreciable permeation properties.
- 1 January 1994
- Published by The Membrane Society of Japan in MEMBRANE
- Vol. 19 (3) , 165-170
Preparation of Inorganic Membranes by Sol-gel Method for Gas Separation.
Development of sol-gel derived porous ceramic membrane is reviewed from the standpoint of gas separation at high temperature. Amorphous silica membranes have attained both high hydrogen selectivity and permeability. However, γ-alumina membranes coated by Yoldas method have pores of 2-10 nm in size, and their hydrogen selectivity is relatively low due to the Knudsen diffusion mechanism. Modification of pores by impregnation of ultrafine particles or chemical vapor deposition improves the selectivity by the size of molecules. The interaction of molecules with pore walls is important for the separation of polar gases. Multicomponent oxide membranes are thermally and chemically stable at high temperature and have appreciable permeation properties.