IPIvete Peixoto Pinheiro

Ivete Peixoto Pinheiro

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ivete Peixoto Pinheiro has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Mathematical Simulation of the Two-Phase Flow for Oil-Water Separation in Hydrocyclones

    by André Felipe Queiroz Barbosa, Ricardo Luiz Perez Teixeira, Gabriela Leite Mota, Ivete Peixoto Pinheiro, Leonardo Neves

    Hydrocyclones are devices used on offshore petroleum platforms to separate the water-oil system. They are applied in the second stage of separation, and their use in the first stage is also a viable option, as gravitational separators are inconveniently heavy, require too much space, and prolong the process. Dimensioning an innovative hydrocyclone can be made easier by computational simulation of the flow within the device, which can yield the geometry necessary for the targeted separation. A mathematical model of a current hydrocyclone was developed and validated, which should be adapted to fit the dimensions required for the new device. Steady-state Computational Fluid Dynamics simulations were performed with hexahedral meshes, the Reynolds Stress turbulence model, and the Eulerian-Eulerian multiphase approach. Average velocity and pressure were applied as boundary conditions at the inlets and outlets, respectively. The obtained mean velocity profiles follow the axisymmetric flow pattern observed in the actual device. A visual comparison with another mathematical model of the same hydrocyclone confirms such similarity. This likeness to the physical model validates the proposed model, although improvements remain to be implemented in future studies.

  • Open Access

    Influence of Niobium Adding on the Microstructure and Abrasive Wear Resistance of a Heat-Treated High-Chromium Near-Eutectic Cast Iron Alloy

    by Ismael Nogueira Rabelo de Melo, Anderson Edson da Silva, Fabrício Gonçalves de Faria, Ivete Peixoto Pinheiro, Leonardo Roberto da Silva, Roberto Magalhães Paniago


  • Open Access

    Metal magnesium industry waste for partial replacement of Portland cement

    by Maysa Lorena Figueiredo Martins, Richard Rodrigues Barreto, Paulo Roberto Ribeiro Soares Junior, Ivete Peixoto Pinheiro, Augusto Cesar da Silva Bezerra

    The high demand for concrete has triggered studies on the mitigation of Portland cement production impacts, such as greenhouse gas emissions and energy demands, in addition to enabling cost reduction. Partial replacement of cement with other materials has been employed as an alternative to minimize the damage caused by the cement industry. In this regard, it is necessary to use materials that efficiently replace cement clinker. This study uses waste generated from the production of metallic magnesium as a partial replacement for Portland cement. The substitution is aimed at reducing the amount of clinker used, as its production necessitates high energy consumption and results in emission of large quantities of CO2 into the atmosphere. The tailings were characterized via X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM), and granulometric analysis. For evaluating the mechanical behavior and porosity, 25% of the cement (by mass) was replaced with tailings, and the resulting composite was molded into cylindrical specimens. After curing for 28 and 91 days, all specimens underwent compression testing. The results of the physical characterization showed that more than 65% of the tailing grain was lesser than 45 μm in size, which contributes to the packaging effect. In terms of the chemical and mineralogical composition, the tailing had high levels of calcium, and the predominant phases could be identified. The compressive strength of the mortar with substitution was higher than 40 MPa. The convergence observed between the results of the different characterization techniques demonstrates the efficiency of using the waste as a supplementary cementitious material.


  • Open Access

    Effect of niobium addition on the properties and microstructure of a high chromium cast iron alloy

    by Ismael Nogueira Rabelo de Melo, Anderson Edson da Silva, Leonardo Roberto da Silva, Ivete Peixoto Pinheiro

    High chromium cast iron (HCCI) is usually employed in equipment that experience high abrasive wear and therefore requires high resistance. Niobium could be added to these alloys to improve their resistance to wear. This study consisted in addressing the influence of 0.5% and 1.0% of niobium on the microstructure of a 26% Cr and 2.8% C HCCI alloy. Standard samples – without niobium – and samples with 0.5% and 1.0% Nb were melted, cut and then machined into adequate dimensions for tests. Two groups of samples – with and without heat treatment – were analyzed through X-ray Diffraction (XRD), optical microscopy, scanning electron microscopy (SEM), Vickers and Rockwell-C hardness. Carbides Volume Fraction (CVF) was quantified in the heat-treated samples. The majority of NbC carbides were observed to be thin and presented a hook shaped morphology. In addition, it was noted a precipitation of Nb-rich layers around the M7C3 carbides, which could act as a higher hardness coating. There was significant reduction in carbide volume fraction, from an initial 33.3% to 28.1% for the 0.5 % Nb alloy, and further reduction to 24.9% for the 1.0% Nb alloy, it was also noted an alteration on the quasi-eutectic microstructure to a hypoeutectic microstructure. The NbC carbides prevented hardness reduction as a result of lowering the CVF in heat-treated alloys; however, the alloys without heat treatment experienced reductions in hardness.

  • Open Access

    Avaliação da susceptibilidade de precipitação da fase sigma na soldagem do aço inoxidável duplex SAF2205

    by Camila Soares Fonseca, Sidney Nicodemos da Silva, Henrique Giacomini Gomes, Danillo Wisky Silva, José Benedito Guimarães Júnior, Ivete Peixoto Pinheiro

    RESUMO A soldagem de aços inoxidáveis duplex é uma operação crítica, devido aos ciclos térmicos aos quais o material é submetido, que podem favorecer a precipitação de fases deletérias. Nesse contexto, objetivo dessa pesquisa é analisar a influência da energia de soldagem na susceptibilidade à formação de fase sigma no aço duplex SAF2205. As chapas de SAF2205 foram soldadas pelo processo de soldagem GMAW, variando a energia de soldagem em 0,5kJ/mm, 1,0kJ/mm, 1,5 kJ/mm. O material foi analisado por microscopia óptica, DRX e microdureza Vickers. A análise da microestrutura das chapas evidenciou que quanto maior o aporte térmico utilizado na soldagem, maior é a quantidade de austenita e maior o tamanho do grão austenítico e ferrítico. Por meio do perfil de microdureza verificou-se que ocorre a redução da dureza na ZTA. Através do DRX foi determinada a presença de fase sigma nas regiões de solda para amostras soldadas com energia de soldagem de 1,0kJ/mm e 1,5 kJ/mm. Concluiu-se que pode-se utilizar nos processos de soldagem GMAW de aços inoxidáveis duplex SAF2205 com 4 mm de espessura aporte térmico próximo de 0,5 kJ/mm quando o objetivo for evitar a formação de fase sigma e aproximadamente igual a 1,5 kJ/mm quando o objetivo for manter percentual das fases na ZTA e ZF próximo ao do metal.


  • Open Access

    Influência do aporte térmico sobre a morfologia da austenita e na quantidade das fases em chapas soldadas de aço inoxidável duplex SAF2205

    by Camila Soares Fonseca, Ivete Peixoto Pinheiro, Sidney Nicodemos da Silva

    Os aços inoxidáveis duplex possuem uma microestrutura na qual a composição de ferrita e austenita, tem frações volumétricas próximas a 50 %. Esses são utilizados na fabricação de diversos componentes e produtos, principalmente para aplicações na indústria petrolífera. Nestas aplicações muitas vezes são utilizados processos de soldagem. Para mitigar as alterações provocadas por esse processo nas propriedades do material é necessária uma escolha adequada dos parâmetros de soldagem. Neste contexto, o objetivo desse trabalho é avaliar o efeito do aporte térmico sobre a morfologia da austenita e na quantidade das fases, além de identificar qual condição de soldagem proporciona um equilíbrio das frações volumétricas de ferrita e austenita. Os materiais analisados são chapas de aço inoxidável duplex SAF2205, soldadas pelo processo de soldagem GMAW, na ESAB, variando-se o aporte térmico em 0,5, 1,0 e 1,5 kJ/mm. Após a soldagem, as chapas foram cortadas, preparadas para a análise metalográfica da morfologia de austenita formada e para a quantificação das fases. Os resultados mostraram a presença da austenita alotriomórfica de contorno de grão, a austenita de Widmanstätten e a austenita intragranular. Foi verificado que o aporte térmico que menos alterou o balanceamento das fases ferrita e austenita foi o de 1,5 kJ/mm, concluindo que se deve utilizá-lo quando o objetivo for manter a proporção volumétrica das fases no aço duplex SAF2205.