Deepak Srivastava
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Deepak Srivastava has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Archana Devi
Department of Plastic Technology, H.B. Technological Institute, Kanpur 208 002, Uttar Pradesh, India
3 shared publicationsGarima Tripathi
Department of Plastic Technology, H.B. Technological Institute, Nawab Ganj, Kanpur 208 002, U.P. India
3 shared publicationsG. N. Mathur
Defence Materials and Store Research and Development Establishment, Kanpur 208 012, India
2 shared publicationsRanjana Yadav
Department of Plastic Technology, H. B. Technological Institute, Nawab Ganj, Kanpur 208 002, Uttar Pradesh, India
2 shared publications- Shailesh Kumar Shukla
H. B. Technological Institute
2 shared publications D. C. Saxena
Department of Food Technology, SLIET, Longowal, Distt. Sangrur, Punjab, India
1 shared publication
Latest Publications
- 25 February 2009
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 112 (5) , 3119-3126
Cure kinetics of ternary blends of epoxy resins studied by nonisothermal DSC data
The curing kinetics of blends of diglycidyl ether of bisphenol A (DGEBA), cycloaliphatic epoxy resins, and carboxyl‐terminated butadiene‐acrylonitrile random copolymer (CTBN) in presence of 4,4′‐diamino diphenyl sulfone (DDS) as the curing agent was studied by nonisothermal differential scanning calorimetry (DSC) technique at different heating rates. The kinetic parameters of the curing process were determined by isoconversional method given by Malek for the kinetic analysis of the data obtained by the thermal treatment. A two‐parameter (m, n) autocatalytic model (Sestak‐Berggren equation) was found to be the most adequate selected to describe the cure kinetics of the studied epoxy resins. The values of Ea were found to be 88.6 kJ mol−1 and 61.6 kJ mol−1, respectively, for the studied two sample series. Nonisothermal DSC curves obtained using the experimental data show a good agreement with that theoretically calculated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009
- 25 February 2009
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 112 (5) , 3119-3126
Cure kinetics of ternary blends of epoxy resins studied by nonisothermal DSC data
The curing kinetics of blends of diglycidyl ether of bisphenol A (DGEBA), cycloaliphatic epoxy resins, and carboxyl‐terminated butadiene‐acrylonitrile random copolymer (CTBN) in presence of 4,4′‐diamino diphenyl sulfone (DDS) as the curing agent was studied by nonisothermal differential scanning calorimetry (DSC) technique at different heating rates. The kinetic parameters of the curing process were determined by isoconversional method given by Malek for the kinetic analysis of the data obtained by the thermal treatment. A two‐parameter (m, n) autocatalytic model (Sestak‐Berggren equation) was found to be the most adequate selected to describe the cure kinetics of the studied epoxy resins. The values of Ea were found to be 88.6 kJ mol−1 and 61.6 kJ mol−1, respectively, for the studied two sample series. Nonisothermal DSC curves obtained using the experimental data show a good agreement with that theoretically calculated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009
- 24 November 2008
- Published by Elsevier in European Polymer Journal
- Vol. 45 (3) , 946-952
Studies on the process variables of the condensation reaction of cardanol and formaldehyde by response surface methodology
- 24 November 2008
- Published by Elsevier in European Polymer Journal
- Vol. 45 (3) , 946-952
Studies on the process variables of the condensation reaction of cardanol and formaldehyde by response surface methodology
- 1 September 2007
- Published by Wiley in Advances in Polymer Technology
- Vol. 26 (4) , 258-271
Effect of carboxyl‐terminated butadiene acrylonitrile copolymer concentration on mechanical and morphological features of binary blends of nonglycidyl‐type epoxy resins
- 1 September 2007
- Published by Wiley in Advances in Polymer Technology
- Vol. 26 (4) , 258-271
Effect of carboxyl‐terminated butadiene acrylonitrile copolymer concentration on mechanical and morphological features of binary blends of nonglycidyl‐type epoxy resins
- 31 August 2007
- Published by Elsevier in European Polymer Journal
- Vol. 43 (8) , 3531-3537
Optimization of the process variables for the synthesis of cardanol-based novolac-type phenolic resin using response surface methodology
- 31 August 2007
- Published by Elsevier in European Polymer Journal
- Vol. 43 (8) , 3531-3537
Optimization of the process variables for the synthesis of cardanol-based novolac-type phenolic resin using response surface methodology
- 30 June 2007
- Published by Elsevier in European Polymer Journal
- Vol. 43 (6) , 2422-2432
Studies on the blends of cardanol-based epoxidized novolac resin and CTPB
- 30 June 2007
- Published by Elsevier in European Polymer Journal
- Vol. 43 (6) , 2422-2432
Studies on the blends of cardanol-based epoxidized novolac resin and CTPB
- 15 January 2007
- Published by Springer Nature in Journal of Materials Science
- Vol. 42 (9) , 3215-3222
Studies on the blends of modified epoxy resin and carboxyl-terminated polybutadiene (CTPB)—II: thermal and mechanical characteristics
- 15 January 2007
- Published by Springer Nature in Journal of Materials Science
- Vol. 42 (9) , 3215-3222
Studies on the blends of modified epoxy resin and carboxyl-terminated polybutadiene (CTPB)—II: thermal and mechanical characteristics
- 23 August 2006
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 102 (3) , 2730-2737
Cardanol‐based novolac‐type phenolic resins. I. A kinetic approach
Novolac resins having two different mole ratios of cardanol‐to‐formaldehyde (1:0.6 and 1:0.8) were prepared by using aliphatic tricarboxylic acid as catalyst at four different temperatures ranging between 100 and 130°C with an interval of 10°C. The synthesized novolacs were confirmed by infrared spectroscopic analysis with the appearance of characteristic groups of the novolac resin. The reaction between cardanol (C) and formaldehyde (F) was found to follow second‐order rate kinetics as determined by two different approaches. The over all rate constant (k) increased with the increase of C/F molar ratio. Based on the value of k, various other kinetic parameters such as activation energy (Ea), change in enthalpy (ΔH), entropy (ΔS), and free energy (ΔG) of the reaction were also evaluated. The values of Ea and ΔH were found to be decreased with the increase of C/F molar ratio from 1:0.6 to 1:0.8. These values revealed the nature of the condensation reaction between cardanol and formaldehyde in presence of tricarboxylic acid catalysts. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:2730–2737, 2006
- 23 August 2006
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 102 (3) , 2730-2737
Cardanol‐based novolac‐type phenolic resins. I. A kinetic approach
Novolac resins having two different mole ratios of cardanol‐to‐formaldehyde (1:0.6 and 1:0.8) were prepared by using aliphatic tricarboxylic acid as catalyst at four different temperatures ranging between 100 and 130°C with an interval of 10°C. The synthesized novolacs were confirmed by infrared spectroscopic analysis with the appearance of characteristic groups of the novolac resin. The reaction between cardanol (C) and formaldehyde (F) was found to follow second‐order rate kinetics as determined by two different approaches. The over all rate constant (k) increased with the increase of C/F molar ratio. Based on the value of k, various other kinetic parameters such as activation energy (Ea), change in enthalpy (ΔH), entropy (ΔS), and free energy (ΔG) of the reaction were also evaluated. The values of Ea and ΔH were found to be decreased with the increase of C/F molar ratio from 1:0.6 to 1:0.8. These values revealed the nature of the condensation reaction between cardanol and formaldehyde in presence of tricarboxylic acid catalysts. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:2730–2737, 2006
- 1 June 2006
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 45 (7) , 879-883
Studies on Mechanical and Thermal Properties of Ternary Blends of Polyethylenes Having Fixed Percentage of High-Density Polyethylene—II
Six film samples of varying compositions of low-density polyethylene (LDPE); (20–45 wt%) and linear low-density polyethylene (LLDPE); (25–45 wt%) having a fixed percentage of high-density polyethylene (HDPE) at 30 wt% have been extruded by melt blending in a single screw extruder (L/D ratio = 20:1) of uniform thickness of 2 mil. The tensile strength and elongation at break have been found to increase up to 40 wt% with LLDPE addition, starting from 25 wt% LLDPE, in the blends and then decreased. The blend sample containing 30 wt% LDPE, 40 wt% LLDPE, and 30 wt% HDPE (sample C-300) was found to be more thermally stable blend amongst all the prepared blends. In most of the blends, two exothermic peaks appeared that showed the formation of immiscible blend systems; this was further confirmed by scanning electron microscopic (SEM) analysis.
- 1 June 2006
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 45 (7) , 879-883
Studies on Mechanical and Thermal Properties of Ternary Blends of Polyethylenes Having Fixed Percentage of High-Density Polyethylene—II
Six film samples of varying compositions of low-density polyethylene (LDPE); (20–45 wt%) and linear low-density polyethylene (LLDPE); (25–45 wt%) having a fixed percentage of high-density polyethylene (HDPE) at 30 wt% have been extruded by melt blending in a single screw extruder (L/D ratio = 20:1) of uniform thickness of 2 mil. The tensile strength and elongation at break have been found to increase up to 40 wt% with LLDPE addition, starting from 25 wt% LLDPE, in the blends and then decreased. The blend sample containing 30 wt% LDPE, 40 wt% LLDPE, and 30 wt% HDPE (sample C-300) was found to be more thermally stable blend amongst all the prepared blends. In most of the blends, two exothermic peaks appeared that showed the formation of immiscible blend systems; this was further confirmed by scanning electron microscopic (SEM) analysis.
- 24 January 2006
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 100 (3) , 1802-1808
Blends of modified epoxy resin and carboxyl‐terminated polybutadiene. I
Six blend samples were prepared by the physical mixing of epoxidized resole (EDR) with different weight ratios of carboxyl‐terminated polybutadiene (CTPB) liquid rubber ranging from 0 to 25 wt % in intervals of 5 wt %. The formation of various reaction products during the curing of unblended EDR and CTPB‐blended EDR were studied with Fourier transform infrared spectroscopy. The curing time at 100°C for the blend sample containing 15 wt % CTPB was the least among all of the blend samples. This blend sample, also, showed the highest initial degradation temperature, as obtained from thermogravimetric analysis thermograms, which indicated that it was the most thermally stable matrix system. The films of coatings based on the blend of EDR with 15 wt % CTPB offered the highest resistance toward different concentrations of acids and alkalis compared to the films having 5, 10, 20, and 25 wt % CTPB in the EDR/CTPB blends. Solvents showed almost the same behavior as acids and alkalis for these films except for hydrocarbon solvents such as mineral turpentine oil, toluene, and xylene. The resistance toward these solvents was poor and slightly inferior to those found with EDR unblended with CTPB. The tensile, flexural, and impact strengths of the molded specimens derived from the EDR/CTPB blends initially increased up to 15 wt % CTPB addition in the blend and then decreased, whereas the elongation at break remained constant for all blend compositions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1802–1808, 2006
- 24 January 2006
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 100 (3) , 1802-1808
Blends of modified epoxy resin and carboxyl‐terminated polybutadiene. I
Six blend samples were prepared by the physical mixing of epoxidized resole (EDR) with different weight ratios of carboxyl‐terminated polybutadiene (CTPB) liquid rubber ranging from 0 to 25 wt % in intervals of 5 wt %. The formation of various reaction products during the curing of unblended EDR and CTPB‐blended EDR were studied with Fourier transform infrared spectroscopy. The curing time at 100°C for the blend sample containing 15 wt % CTPB was the least among all of the blend samples. This blend sample, also, showed the highest initial degradation temperature, as obtained from thermogravimetric analysis thermograms, which indicated that it was the most thermally stable matrix system. The films of coatings based on the blend of EDR with 15 wt % CTPB offered the highest resistance toward different concentrations of acids and alkalis compared to the films having 5, 10, 20, and 25 wt % CTPB in the EDR/CTPB blends. Solvents showed almost the same behavior as acids and alkalis for these films except for hydrocarbon solvents such as mineral turpentine oil, toluene, and xylene. The resistance toward these solvents was poor and slightly inferior to those found with EDR unblended with CTPB. The tensile, flexural, and impact strengths of the molded specimens derived from the EDR/CTPB blends initially increased up to 15 wt % CTPB addition in the blend and then decreased, whereas the elongation at break remained constant for all blend compositions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1802–1808, 2006
- 2 January 2004
- Published by Wiley in Advances in Polymer Technology
- Vol. 23 (1) , 59-70
Thermo‐oxidative degradation studies of ternary blends of polyethylenes
Films of low‐density polyethylene (LDPE) and high‐density polyethylene (HDPE) each containing 25 wt % of linear low‐density polyethylene (LLDPE) were extruded by melt blending in a single screw extruder (L/D ratio = 20:1). The samples were aged at 55, 70, 85, and 100°C for different time periods up to 600 h. The change in molecular structure and formation of oxygenated and unsaturated groups during thermo‐oxidative degradation were investigated by infrared spectroscopy. Viscosity‐average molecular weight (M̄v) was found to decrease at slower rate in the initial hours of ageing, whereas on prolonged ageing, it decreased at a faster rate. In some blend samples, the tensile strength and elongation at break initially increased up to certain hours of ageing, and then decreased while in some blends both tensile strength and elongation‐at‐break varied differently. Increase in percent gel content supports the formation of cross‐links between the molecular chains. Thermal stability of the samples also decreased with ageing time and temperature. © 2004 Wiley Periodicals, Inc. Adv Polym Techn 23: 59–70, 2004; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/adv.10067
- 2 January 2004
- Published by Wiley in Advances in Polymer Technology
- Vol. 23 (1) , 59-70
Thermo‐oxidative degradation studies of ternary blends of polyethylenes
Films of low‐density polyethylene (LDPE) and high‐density polyethylene (HDPE) each containing 25 wt % of linear low‐density polyethylene (LLDPE) were extruded by melt blending in a single screw extruder (L/D ratio = 20:1). The samples were aged at 55, 70, 85, and 100°C for different time periods up to 600 h. The change in molecular structure and formation of oxygenated and unsaturated groups during thermo‐oxidative degradation were investigated by infrared spectroscopy. Viscosity‐average molecular weight (M̄v) was found to decrease at slower rate in the initial hours of ageing, whereas on prolonged ageing, it decreased at a faster rate. In some blend samples, the tensile strength and elongation at break initially increased up to certain hours of ageing, and then decreased while in some blends both tensile strength and elongation‐at‐break varied differently. Increase in percent gel content supports the formation of cross‐links between the molecular chains. Thermal stability of the samples also decreased with ageing time and temperature. © 2004 Wiley Periodicals, Inc. Adv Polym Techn 23: 59–70, 2004; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/adv.10067