YKYoung Jin Kim

Young Jin Kim

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Young Jin Kim has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Evaluation of Bond Strength between Setting Retarder Added Concrete and Normal Concrete

    by Jin-Su Son, Chiwon Song, Won-Jong Chin, Young-Jin Kim, Jin-Young Lee

    The large size concrete structures are continuously placed with time delay due to practical reasons. The bond strength between old concrete and new concrete is related with a performance of concrete structures. In order to investigate bond strength of slant shear specimens, the specimens (100 × 100 × 300 mm) were fabricated and tested. Two fractions of setting retarder (0% and 1%), surface roughness (none, brushed, and chipping), and curing hours (8, 16, 24, and 72 hours) were considered as variables. Failure modes, compressive strength, and displacement were measured to evaluate the bond strength of specimens. As a result, chipping treatment, which is commonly applied to increase the bond strength between old and new concrete, did not show significant increase of bond strength. The addition of retarder shows that the increased bond strength compared with the chipping treatment. The addition of the retarder in concrete shows sufficient bond strength after the previous placing of 16 hours. Furthermore, the retarder-added specimens with additional brushing treatment of concrete surfaces showed increase of bond strength more than the specimens without brushing. From the test results, it is confirmed that the addition of the retarder can be a new method to increase the bond strength of the concrete surface in continuous placement of concrete.


  • Open Access

    Correlation between the Compressive Strength and Ultrasonic Pulse Velocity of Cement Mortars Blended with Silica Fume: An Analysis of Microstructure and Hydration Kinetics

    by Geuntae Hong, Sangwoo Oh, Seongcheol Choi, Won-Jong Chin, Young-Jin Kim, Chiwon Song

    The effect of the replacement rate of silica fume (SF) on the correlation between the compressive strength and ultrasonic pulse velocity (UPV) of cement mortar was experimentally analyzed. Specimens were fabricated with different replacement rates of SF, the compressive strength and UPV were measured, and isothermal calorimetry and mercury intrusion porosimetry tests were conducted to analyze the effects of replacement on the hydration kinetics and microstructures on these properties. Field emission scanning electron microscopy analysis was performed to observe SF particles and microstructure. The substitution of SF changed the cement mortar’s hydration kinetics and microstructures, resulting in different strengths and UPVs depending on the replacement rate. The compressive strength and UPV for cement mortars blended with SF also showed a different exponential relationship depending on the SF replacement rate.


  • Open Access

    Estimation on Embedment Length of Anchor Bolt inside Concrete Using Equation for Arrival Time and Shortest Time Path of Ultrasonic Pulse

    by Chiwon Song, Young Jin Kim, Chang Beck Cho, Won Jong Chin, Kwang-Yeun Park

    The bearings or the seismic isolation bearings that play a critical role in bridge structures are fixed to the substructure by anchor bolts. However, the embedment depth of the constructed anchor bolts does often not reach the designed one and may lead to safety issues. The present study proposes an ultrasonic non-destructive testing (NDT) method to verify the embedment depth of the anchor bolts installed on bridges in-service. The P-wave of 50–100 kHz that is usually used in the NDT of concrete was transmitted from the head of the anchor bolt and its arrival time on the concrete cover was measured. The shortest arrival time of the ultrasonic pulse and the corresponding path were then analyzed to formulate their relationship and obtain the distance traveled by the ultrasonic pulse along the anchor by inverse analysis using the equation error estimation. The instability occurring in the inverse analysis is settled by regularization. Finally, the embedment depth of the anchor bolt can be estimated by the analysis of the graph plotting the position of the ultrasonic transmitter and the distance traveled by the pulse along the anchor. The proposed method is validated numerically and experimentally. The method is expected to contribute to the NDT of civil structures by making it possible to estimate the embedment depth of anchor bolts by the means of ultrasonic transducers using P-waves of 50–100 kHz.


  • Open Access

    Dynamic Performance of a New-Type PSC I-girder for Railway Bridge Application

    by Hyejin Yoon, Sung Tae Kim, Won Jong Chin, Young Jin Kim, Jeong-Rae Cho

    This study intends to verify analytically and experimentally the performance of a new type of prestressed concrete (PSC) I-girder for its application as railway bridge. Since the girder-type railway bridge develops relatively low torsional rigidity, there is risk for the dynamic responses to amplify due to the superposition of the torsional mode and flexural mode. The superposition of the torsional and flexural modes as well as the dynamic stability of the railway bridge were examined through dynamic analysis. Three-dimensional modelling was built to be suitable for carrying out moving load analysis. Four different span lengths of 30, 35, 40 and 45 m adopted considering the most applied span length currently and future lengthening of the span length. Moreover, a full-scale girder specimen with span length of 35 m was fabricated and subjected to dynamic loading. The measured dynamic responses were then compared to the analytic values. Finally, the ultimate bearing capacity of the specimen was verified by static loading test.


  • Open Access

    Comparing Rubber Bearings and Eradi-Quake System for Seismic Isolation of Bridges

    by Chang Beck Cho, Young Jin Kim, Won Jong Chin, Jin-Young Lee

    Seismic isolation systems have been used worldwide in bridge structures to reduce vibration and avoid collapse. The seismic isolator, damper, and Shock Transmission Unit (SUT) are generally adopted in the seismic design of bridges to improve their seismic safety with economic efficiency. There are several seismic isolation systems, such as Natural Rubber Bearing (NRB), Lead Rubber Bearing (LRB), and the Eradi-Quake System (EQS). EQS as a new technology is expected to effectively reduce both seismic force and displacement, but there is still some need to verify whether it might provide an economical and practical strategy for a bridge isolation system. Moreover, it is important to guarantee consistent performance of the isolators by quality control. A comparative evaluation of the basic properties of the available seismic isolators is thus necessary to achieve a balance between cost-effectiveness and the desired performance of the bridge subjected to extreme loading. Accordingly, in this study, the seismic response characteristics of the seismic isolation systems for bridges were investigated by conducting compressive test and compressive-shear test on NRB, LRB, and EQS.


  • Open Access

    Interface Shear Strength at Various Joint Types in High-Strength Precast Concrete Structures

    by Young-Jin Kim, Won-Jong Chin, Se-Jin Jeon

    More precast concrete structures have recently been constructed due to their many advantages when compared to conventional cast-in-place construction. Structural behavior at the joints between the precast segments can significantly affect the overall integrity, safety, and serviceability of the structure. In this study, therefore, the interface shear strength of high-strength precast members was investigated by performing push-off tests with the following variables: compressive strength of precast members, dry or wet joint, number and height of shear keys, joint width, filler type, curing temperature, and lateral compressive stress. The test results were analyzed to reveal the effect of each test variable on the joint shear strengths of the specimens. For instance, the failure loads were increased by 14–140%, depending on the lateral compressive stress, as the specified compressive strength of the precast members was increased from 80 to 150 MPa in the dry joints. The failure loads of the wet joints strongly depended on the strength of the filler rather than on that of the precast members and, as a result, the specimen with ultra-high-strength concrete filler was 46–48% stronger than those with high-strength mortar filler. The shear strengths of various joint types obtained from the test were further analyzed in comparison with the predictive equations of Japan Society of Civil Engineers (JSCE) and American Association of State Highway and Transportation Officials (AASHTO) with the aim of validating the appropriateness of these design provisions. In particular, an improved value of a coefficient in the JSCE equation is proposed to cover a range of compressive strengths in various precast members and filling materials.


  • Open Access

    Experimental Validation of Slip-Forming Using Ultrasonic Sensors

    by Hyejin Yoon, Young Jin Kim, Won Jong Chin, Jun Won Kang, Hyun-Moo Koh

    Slip-forming in concrete construction enables the continuous placement of concrete using a climbing form, the efficiency of which depends on appropriate slip-up timing. This implies the importance of knowing accurately the development of concrete strength over time, which has been assessed manually to date in construction fields. This paper presents a method for automating the slip-forming process by determining the optimal slip-up time using the in-situ strength of concrete. The strength of concrete is evaluated by a formula relating the strength to the surface wave velocity measured with ultrasonic sensors. Specifically, this study validates the applicability of the slip-form system with ultrasonic sensors for continuously monitoring the hardening of concrete through its application in several construction sites. To this end, a slip-form system with a pair of ultrasonic modules at the bottom of the panel was tested and the time variation of surface wave velocity in the concrete material was monitored during the slip-forming process. The results show that the proposed method can provide the optimal slip-up time of the form to automate the slip-forming process. This approach is expected to apply to other construction technologies that required the continuous monitoring of concrete strength for construction efficiency as well as quality maintenance.


  • Open Access

    Evaluation of Early-Age Concrete Compressive Strength with Ultrasonic Sensors

    by Hyejin Yoon, Young Jin Kim, Hee Seok Kim, Jun Won Kang, Hyun-Moo Koh

    Surface wave velocity measurement of concrete using ultrasonic sensors requires testing on only one side of a member. Thus, it is applicable to concrete cast inside a form and is often used to detect flaws and evaluate the compressive strength of hardened concrete. Predicting the in situ concrete strength at a very early stage inside the form helps with determining the appropriate form removal time and reducing construction time and costs. In this paper, the feasibility of using surface wave velocities to predict the strength of in situ concrete inside the form at a very early stage was evaluated. Ultrasonic sensors were used to measure a series of surface waves for concrete inside a form in the first 24 h after placement. A continuous wavelet transform was used to compute the travel time of the propagating surface waves. The cylindrical compressive strength and penetration resistance tests were also performed during the test period. Four mixtures and five curing temperatures were used for the specimens. The surface wave velocity was confirmed to be applicable to estimating the concrete strength at a very early age in wall-like elements. An empirical formula is proposed for evaluating the early-age compressive strength of concrete considering the 95% prediction intervals.


  • Open Access

    Experimental verification of GFRP slip-form for in-situ application

    by Hyun-Joong Kim, Youngjin Kim, Jongsung Sim


  • Open Access

    Estimation of Prestress Force Distribution in Multi-Strand System of Prestressed Concrete Structures Using Field Data Measured by Electromagnetic Sensor

    by Keunhee Cho, Jeong-Rae Cho, Sung Tae Kim, Sung Yong Park, Young-Jin Kim, Young-Hwan Park

    The recently developed smart strand can be used to measure the prestress force in the prestressed concrete (PSC) structure from the construction stage to the in-service stage. The higher cost of the smart strand compared to the conventional strand renders it unaffordable to replace all the strands by smart strands, and results in the application of only a limited number of smart strands in the PSC structure. However, the prestress forces developed in the strands of the multi-strand system frequently adopted in PSC structures differ from each other, which means that the prestress force in the multi-strand system cannot be obtained by simple proportional scaling using the measurement of the smart strand. Therefore, this study examines the prestress force distribution in the multi-strand system to find the correlation between the prestress force measured by the smart strand and the prestress force distribution in the multi-strand system. To that goal, the prestress force distribution was measured using electromagnetic sensors for various factors of the multi-strand system adopted on site in the fabrication of actual PSC girders. The results verified the possibility to assume normal distribution for the prestress force distribution per anchor head, and a method computing the mean and standard deviation defining the normal distribution is proposed. This paper presents a meaningful finding by proposing an estimation method of the prestress force based upon field-measured data of the prestress force distribution in the multi-strand system of actual PSC structures.