Vincent G. Harris
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Vincent G. Harris has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Matthew A. Willard
Department of Materials Science and Engineering, Case Western Reserve University, Cleveland, USA
3 shared publications Frank Johnson
Department of Materials Science and Engineering, Carnegie Mellon University
1 shared publicationJ. H. Claassen
Naval Research Laboratory, Washington, DC 20375
1 shared publicationJohn H. Claassen
U.S. Naval Research Laboratory, Materials Physics Branch
1 shared publicationMichael E. McHenry
Department of Materials Science and Engineering, Carnegie Mellon University
1 shared publication- Rhonda M. Stroud
Arizona State University
1 shared publication
Latest Publications
- 1 September 2004
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 75 (9) , 2817-2821
Inductive measurements of magnetic properties of ribbon materials
Inductive measurements of thin ribbon materials are usually done with wrapped toroidal cores. To avoid this time consuming procedure, measurements can also be performed on short straight pieces in a solenoidal setup. We show that demagnetizing effects should be unimportant for the latter case in determining coercive field, saturation field, and core loss. These two types of measurement were performed on samples of amorphous ribbon material. It was found that there is reasonable agreement for these magnetic parameters as long as care was taken to ensure that the samples were strain-free. Strain is particularly important when the material has significant magnetostriction. Based on demagnetization estimates we would expect agreement on permeability determinations in all but the most extreme cases; in fact results can be quite different for the two measurements. Similarly, we can get rather different answers for coercive field when it is very small. This may be due to uniaxial anisotropy which is different for the two sample geometries. It is concluded that the rapid turnaround in solenoid measurements is particularly useful when optimization of saturation field or core loss is of primary importance.
- 1 September 2004
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 75 (9) , 2817-2821
Inductive measurements of magnetic properties of ribbon materials
Inductive measurements of thin ribbon materials are usually done with wrapped toroidal cores. To avoid this time consuming procedure, measurements can also be performed on short straight pieces in a solenoidal setup. We show that demagnetizing effects should be unimportant for the latter case in determining coercive field, saturation field, and core loss. These two types of measurement were performed on samples of amorphous ribbon material. It was found that there is reasonable agreement for these magnetic parameters as long as care was taken to ensure that the samples were strain-free. Strain is particularly important when the material has significant magnetostriction. Based on demagnetization estimates we would expect agreement on permeability determinations in all but the most extreme cases; in fact results can be quite different for the two measurements. Similarly, we can get rather different answers for coercive field when it is very small. This may be due to uniaxial anisotropy which is different for the two sample geometries. It is concluded that the rapid turnaround in solenoid measurements is particularly useful when optimization of saturation field or core loss is of primary importance.
- 1 March 2002
- Published by Springer Nature in JOM
- Vol. 54 (3) , 44-46
Soft magnetic materials: Nanocrystalline alloys from amorphous precursors
- 1 March 2002
- Published by Springer Nature in JOM
- Vol. 54 (3) , 44-46
Soft magnetic materials: Nanocrystalline alloys from amorphous precursors
- Open Access
- 1 January 2002
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 43 (8) , 2000-2005
Soft Magnetic Nanocrystalline Alloys for High Temperature Applications
High temperature inductor applications require improved magnet performance, including simultaneous high magnetization and low core losses at ever higher operation frequencies. Conventional polycrystalline soft magnet alloys are mature technologies with little room for meaningful improvement. Recently, nanocrystalline soft magnetic materials possessing reduced hysteretic losses and offering higher operation frequencies than conventional alloys have been introduced. These nanocrystalline soft magnets with compositions Fe–Co–Zr–B–(Cu) have been offered as alternatives to the conventional alloys. This paper describes the processing, structure, and magnetic properties of these materials.
- 1 January 2002
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 43 (8) , 2000-2005
Open AccessSoft Magnetic Nanocrystalline Alloys for High Temperature Applications
High temperature inductor applications require improved magnet performance, including simultaneous high magnetization and low core losses at ever higher operation frequencies. Conventional polycrystalline soft magnet alloys are mature technologies with little room for meaningful improvement. Recently, nanocrystalline soft magnetic materials possessing reduced hysteretic losses and offering higher operation frequencies than conventional alloys have been introduced. These nanocrystalline soft magnets with compositions Fe–Co–Zr–B–(Cu) have been offered as alternatives to the conventional alloys. This paper describes the processing, structure, and magnetic properties of these materials.