Daogang Lu
Daogang Lu has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Danting Sui
North China Elect Power Univ, Beijing 102206, Peoples R China
2 shared publications - Qiong Cao2 shared publications
- Siyu Lyu
North China Electric Power University, Beijing 102206, China
2 shared publications Biyao Ren
1 shared publicationCong Wang
Research Institute of Nuclear Power Operation, Hubei, Wuhan 430223, China
1 shared publication- Feng Shen
State Power Investment Corporation Research Institute, Beijing 102209, China
1 shared publication
Latest Publications
- Top Cited PapersOpen Access
Comparative Analysis on the Characteristics of Liquid Lead and Lead–Bismuth Eutectic as Coolants for Fast Reactors
With the increasing global demand for sustainable energy, the importance of advanced nuclear technologies, such as fourth-generation reactors, has become increasingly prominent. Fourth-generation reactors often use non-water coolants, among which liquid lead and lead–bismuth eutectics (LBEs) are highly promising, making lead-cooled fast reactors (LFRs) a popular area of research internationally. On the basis of extensive analysis and comparison conducted previously, this article summarizes and analyzes the advantages, problems, and differences in lead and LBE as LFR coolants. Overall, both lead and LBE have excellent neutronic characteristics, good heat transfer performance, and chemical inertness, and make LFRs highly efficient in nuclear fuel utilization, inherently safe, and relatively simplified in design. However, both of them corrode materials severely and produce highly toxic 210Po, which are the problems that need to be considered for further engineering development. Moreover, LBE has a lower melting point, which allows a wider temperature range and lower insulation requirements in its design, making it easier to achieve engineering and miniaturization under the same conditions. Lead has a lower cost, is less corrosive to materials, and produces less 210Po, which makes it a more ideal coolant for future development.
Top Cited PapersOpen AccessComparative Analysis on the Characteristics of Liquid Lead and Lead–Bismuth Eutectic as Coolants for Fast Reactors
With the increasing global demand for sustainable energy, the importance of advanced nuclear technologies, such as fourth-generation reactors, has become increasingly prominent. Fourth-generation reactors often use non-water coolants, among which liquid lead and lead–bismuth eutectics (LBEs) are highly promising, making lead-cooled fast reactors (LFRs) a popular area of research internationally. On the basis of extensive analysis and comparison conducted previously, this article summarizes and analyzes the advantages, problems, and differences in lead and LBE as LFR coolants. Overall, both lead and LBE have excellent neutronic characteristics, good heat transfer performance, and chemical inertness, and make LFRs highly efficient in nuclear fuel utilization, inherently safe, and relatively simplified in design. However, both of them corrode materials severely and produce highly toxic 210Po, which are the problems that need to be considered for further engineering development. Moreover, LBE has a lower melting point, which allows a wider temperature range and lower insulation requirements in its design, making it easier to achieve engineering and miniaturization under the same conditions. Lead has a lower cost, is less corrosive to materials, and produces less 210Po, which makes it a more ideal coolant for future development.
- 7 July 2023
- Published by Elsevier in Progress in Nuclear Energy
- Vol. 163
Experimental investigation on the heat transfer characteristics of argon space containing sodium vapor
- 7 July 2023
- Published by Elsevier in Progress in Nuclear Energy
- Vol. 163
Experimental investigation on the heat transfer characteristics of argon space containing sodium vapor
- Open Access
- 16 July 2021
- Published by ASME International
Code to Code Validation of SAC-3D Based on EBR-II Benchmark Problem
Neutronics calculation model plays a very important role in applying a specify simulation of a reactor system. The accuracy of the reactor core neutronics calculation results can hugely affect the final results of the reactor system analysis. At present, most of the system analysis codes apply the point reactor kinetics calculation model as the method to do the neutronics
- 16 July 2021
- Published by ASME International
Open AccessCode to Code Validation of SAC-3D Based on EBR-II Benchmark Problem
Neutronics calculation model plays a very important role in applying a specify simulation of a reactor system. The accuracy of the reactor core neutronics calculation results can hugely affect the final results of the reactor system analysis. At present, most of the system analysis codes apply the point reactor kinetics calculation model as the method to do the neutronics
- Open Access
- 16 July 2021
- Published by ASME International
Stress Analysis of the Lower Head of Central Measuring Shroud Under Thermal Striping and Thermal Shock Conditions
The central measuring shroud supplies support and guiding of the control rods and in-vessel measuring equipment. The distance between the core outlet and the lower head of central measuring shroud (LHCMS), which is located above the core outlet, is only 500mm. Therefore, the LHCMS will be affected by the coolant for a long period. In the normal operating conditions of the reactors,
- 16 July 2021
- Published by ASME International
Open AccessStress Analysis of the Lower Head of Central Measuring Shroud Under Thermal Striping and Thermal Shock Conditions
The central measuring shroud supplies support and guiding of the control rods and in-vessel measuring equipment. The distance between the core outlet and the lower head of central measuring shroud (LHCMS), which is located above the core outlet, is only 500mm. Therefore, the LHCMS will be affected by the coolant for a long period. In the normal operating conditions of the reactors,
- 1 August 2020
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 364
Neutronics benchmark analysis of the EBR-II SHRT-45R with SAC-3D
- 1 August 2020
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 364
Neutronics benchmark analysis of the EBR-II SHRT-45R with SAC-3D
- 23 December 2019
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 360, 110495
Experimental study on the circulating-cavity flow and an innovative central baffle design in a steam generator
- 23 December 2019
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 360, 110495
Experimental study on the circulating-cavity flow and an innovative central baffle design in a steam generator
- 1 November 2016
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 97, 36-46
Simulation on the hydraulic characteristics of SFR SG using “single-hole plate + tube bundles” (SHTB) hybrid porous media model
- 1 November 2016
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 97, 36-46
Simulation on the hydraulic characteristics of SFR SG using “single-hole plate + tube bundles” (SHTB) hybrid porous media model
- 19 April 2016
- Published by Walter de Gruyter GmbH in Kerntechnik
- Vol. 81 (2) , 142-144
A spray cooling technique for spent fuel assembly stored in pool
For the safety of spent nuclear fuel assemblies stored in storage pool in the extreme condition where the water is lost completely, a passive spray cooling technique was designed, and its effectiveness has been validated by a functional experiment. The spray cooling characteristics of the spent fuel assembly have also been investigated by the experiment.
- 19 April 2016
- Published by Walter de Gruyter GmbH in Kerntechnik
- Vol. 81 (2) , 142-144
A spray cooling technique for spent fuel assembly stored in pool
For the safety of spent nuclear fuel assemblies stored in storage pool in the extreme condition where the water is lost completely, a passive spray cooling technique was designed, and its effectiveness has been validated by a functional experiment. The spray cooling characteristics of the spent fuel assembly have also been investigated by the experiment.
- 10 January 2012
- Published by Springer Nature in Transactions of Tianjin University
- Vol. 18 (1) , 73-78
Network reliability analysis of digital instrument and control system with GO-FLOW methodology
- 10 January 2012
- Published by Springer Nature in Transactions of Tianjin University
- Vol. 18 (1) , 73-78
Network reliability analysis of digital instrument and control system with GO-FLOW methodology
- 31 August 2011
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 241 (8) , 2874-2880
Large-amplitude and narrow-band vibration phenomenon of a foursquare fix-supported flexible plate in a rigid narrow channel
- 31 August 2011
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 241 (8) , 2874-2880
Large-amplitude and narrow-band vibration phenomenon of a foursquare fix-supported flexible plate in a rigid narrow channel