Qi Yuan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qi Yuan has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Zhenping Feng
School of Energy and Power Engineering, Xi'an Jiaotong University , Xi'an 710049, China
3 shared publications - Guangyu Zhu
School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China
2 shared publications - Jian Yang
University of Science and Technology of China
2 shared publications - Jin Gao
School of Energy and Power Engineering, Xi'an Jiaotong University, Xi'an 710049, China
2 shared publications - Joon Hock Yeo
Nanyang Technological University
2 shared publications - Jun Li
Institute of Turbomachinery, School of Energy & Power Engineering, Xi'an Jiaotong University , Xi'an 710049, China
2 shared publications
Latest Publications
- Open Access
Impact of Surface Grinding on the Performance of Tilting Pad Bearings
Tilting pad bearings are core components of rotating machinery. Due to factors such as manufacturing, installation and operation, there may be a mismatch between the bearing pad surface and the shaft diameter, leading to issues like high bearing temperature and rotor system vibration. In engineering practice, surface grinding is often used to resolve these problems. This paper analyzed the mechanism of surface grinding, systematically studies the impact of individual or combined surface grinding on the static and dynamic characteristics of tilting pad bearings and summarizes reasonable pre-load adjustment schemes. The results show that the principle of pad surface grinding is to change the pre-load coefficient of the bearings. The grinding of the oil inlet and outlet sides of the pad surface changes the clearance of the pad, increases the pre-load coefficient, reduces the working temperature of the bearing, increases the thickness of the oil film, and increases power consumption; the grinding of the middle parting surface of the pad changes the clearance of the bearing, increases the pre-load coefficient, and increases the main stiffness and damping coefficient of the bearing. Using these results, a fault diagnosis was performed on a turbine unit with excessive vibration during an on-site operation, leading to effective control. The research provides technical references for the condition monitoring of turbine tilting pad bearing vibrations and the safe operation of units, offering significant engineering implications.
Open AccessImpact of Surface Grinding on the Performance of Tilting Pad Bearings
Tilting pad bearings are core components of rotating machinery. Due to factors such as manufacturing, installation and operation, there may be a mismatch between the bearing pad surface and the shaft diameter, leading to issues like high bearing temperature and rotor system vibration. In engineering practice, surface grinding is often used to resolve these problems. This paper analyzed the mechanism of surface grinding, systematically studies the impact of individual or combined surface grinding on the static and dynamic characteristics of tilting pad bearings and summarizes reasonable pre-load adjustment schemes. The results show that the principle of pad surface grinding is to change the pre-load coefficient of the bearings. The grinding of the oil inlet and outlet sides of the pad surface changes the clearance of the pad, increases the pre-load coefficient, reduces the working temperature of the bearing, increases the thickness of the oil film, and increases power consumption; the grinding of the middle parting surface of the pad changes the clearance of the bearing, increases the pre-load coefficient, and increases the main stiffness and damping coefficient of the bearing. Using these results, a fault diagnosis was performed on a turbine unit with excessive vibration during an on-site operation, leading to effective control. The research provides technical references for the condition monitoring of turbine tilting pad bearing vibrations and the safe operation of units, offering significant engineering implications.
- 20 October 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (1)
Static and Rotordynamic Characteristics for Supercritical Carbon Dioxide Spiral Groove Dry Gas Seal With the Tilted Seal Ring
In this paper, considering the installation errors and external disturbances of the shaft end seal in a 14MW supercritical carbon dioxide turbine, a comprehensive numerical study was conducted on the seal static and rotordynamic characteristics for four dry gas seal designs with different coning displacements. To account for the real gas effect of SCO2, a table lookup program was used to obtain the physics properties of CO2 under supercritical and subcritical conditions based on the database of the National Institute of Standards and Technology (NIST). A frequency-dependent rotordynamic coefficients stiffness damping model (KC model) for SCO2 DGS and the mesh deformation technique were adapted to analyze the rotordynamic performance of the designed DGS. Steady-state numerical results of leakage rate, opening force and steady film stiffness were analyzed and compared under 4 coning displacements. Transient numerical results of rotordynamic force coefficients were analyzed and studied under 4 coning displacement ratios and 10 vibration frequencies. Results show that the increase in coning displacement causes a 20% rise in leakage rate and a 2.4% increase in opening force. The tilted seal ring results in a maximum 30%-84% variation of the dynamic stiffness and greatly influences the damping coefficient. From a comprehensive view, the tilt of the seal rings brings undesired influences on both the static and rotor dynamic performance of SCO2 DGS. The distortion of the seal rings due to installation errors and other disturbances should be avoided as far as possible in SCO2 DGSs.
- 20 October 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (1)
Static and Rotordynamic Characteristics for Supercritical Carbon Dioxide Spiral Groove Dry Gas Seal With the Tilted Seal Ring
In this paper, considering the installation errors and external disturbances of the shaft end seal in a 14MW supercritical carbon dioxide turbine, a comprehensive numerical study was conducted on the seal static and rotordynamic characteristics for four dry gas seal designs with different coning displacements. To account for the real gas effect of SCO2, a table lookup program was used to obtain the physics properties of CO2 under supercritical and subcritical conditions based on the database of the National Institute of Standards and Technology (NIST). A frequency-dependent rotordynamic coefficients stiffness damping model (KC model) for SCO2 DGS and the mesh deformation technique were adapted to analyze the rotordynamic performance of the designed DGS. Steady-state numerical results of leakage rate, opening force and steady film stiffness were analyzed and compared under 4 coning displacements. Transient numerical results of rotordynamic force coefficients were analyzed and studied under 4 coning displacement ratios and 10 vibration frequencies. Results show that the increase in coning displacement causes a 20% rise in leakage rate and a 2.4% increase in opening force. The tilted seal ring results in a maximum 30%-84% variation of the dynamic stiffness and greatly influences the damping coefficient. From a comprehensive view, the tilt of the seal rings brings undesired influences on both the static and rotor dynamic performance of SCO2 DGS. The distortion of the seal rings due to installation errors and other disturbances should be avoided as far as possible in SCO2 DGSs.
- Open Access
- 16 July 2021
- Published by ASME International
Design and Investigations on Dry Gas Seal of the Shaft End for 450MWe Supercritical Carbon Dioxide Compressor
The dry gas seal is a promising sealing technology to control the leakage flow through the clearance between the stationary and rotational components of Supercritical Carbon Dioxide (SCO~2~) turbomachinery. The dry gas seal is firstly designed for the SCO~2~ compressor shaft end of the GE's 450MWe Brighton cycle power generation system. Then the effects of the spiral angle and gas
- 16 July 2021
- Published by ASME International
Open AccessDesign and Investigations on Dry Gas Seal of the Shaft End for 450MWe Supercritical Carbon Dioxide Compressor
The dry gas seal is a promising sealing technology to control the leakage flow through the clearance between the stationary and rotational components of Supercritical Carbon Dioxide (SCO~2~) turbomachinery. The dry gas seal is firstly designed for the SCO~2~ compressor shaft end of the GE's 450MWe Brighton cycle power generation system. Then the effects of the spiral angle and gas
- 13 August 2019
- Published by Walter de Gruyter GmbH in International Journal of Turbo & Jet-Engines
- Vol. 39 (1) , 25-36
Numerical Investigation on the Effects of Vortex Generator Locations on Film Cooling Performance
Described in this paper is a numerical investigation on the concept for enhancing film cooling performance by placing vortex generator (VG) upstream the film hole. Six film cooling configurations with different VG locations are investigated, including the distances for VG upstream the film hole (Upstream Distances) of 20 mm, 25 mm, and 30 mm and the VG gaps of 0, 2 mm, 4 mm and 6 mm respectively. The effect of VG locations on film cooling performance were conducted. The film cooling performance is evaluated at the density of 0.97 with the blowing ratio of 1.0. Results obtained show that the twisted flow generated by upstream VG rotates in the opposite direction of kidney vortex, producing an adverse effect on kidney vortex. The enhanced adverse effect could dramatically improve the film cooling performance. Moreover, the intensity of twisted flow is greatly related to the VG locations. The film cooling performance improves with the increasing upstream distances. The film cooling performance improves first and then impairs with increasing VG gaps. In this case, the film cooling performance in the case with gap of 4 mm is superior to those in other cases.
- 13 August 2019
- Published by Walter de Gruyter GmbH in International Journal of Turbo & Jet-Engines
- Vol. 39 (1) , 25-36
Numerical Investigation on the Effects of Vortex Generator Locations on Film Cooling Performance
Described in this paper is a numerical investigation on the concept for enhancing film cooling performance by placing vortex generator (VG) upstream the film hole. Six film cooling configurations with different VG locations are investigated, including the distances for VG upstream the film hole (Upstream Distances) of 20 mm, 25 mm, and 30 mm and the VG gaps of 0, 2 mm, 4 mm and 6 mm respectively. The effect of VG locations on film cooling performance were conducted. The film cooling performance is evaluated at the density of 0.97 with the blowing ratio of 1.0. Results obtained show that the twisted flow generated by upstream VG rotates in the opposite direction of kidney vortex, producing an adverse effect on kidney vortex. The enhanced adverse effect could dramatically improve the film cooling performance. Moreover, the intensity of twisted flow is greatly related to the VG locations. The film cooling performance improves with the increasing upstream distances. The film cooling performance improves first and then impairs with increasing VG gaps. In this case, the film cooling performance in the case with gap of 4 mm is superior to those in other cases.
- Open Access
Influence of Disc Tip Geometry on the Aerodynamic Performance and Flow Characteristics of Multichannel Tesla Turbines
As a competitive small-scale turbomachinery option, Tesla turbines have wide potential in various fields, such as renewable energy generation systems and small power equipment. This paper investigates the influence of disc tip geometry, including its profile and relative height, on the aerodynamic performance and flow characteristics of one-to-one and one-to-many multichannel Tesla turbines. The results indicate that compared to the turbine with blunt tips, the isentropic efficiency of the one-to-one turbine with sharp tips has a little decrease, which is because the relative tangential velocity gradient near the rotational disc walls decreases a little and additional vortices are generated at the rotor inlet, while that of the one-to-many turbine with sharp tips increases significantly, resulting from an increase in the relative tangential velocity in the disc channels and a decrease in the low Mach number and vortex area; for instance the turbine efficiency for the former relatively decreases by 3.6% and that for the latter increases by 13.5% at 30,000 r/min. In addition, the isentropic efficiency of the one-to-many turbine with sharp tips goes up with increasing relative height due to increasing improvement of flow status, and its increment rate slows down. A circular or elliptic tip performs better with lower relative height and a triangular tip behaves better with higher relative height. To sum up, a blunt disc tip is recommended for the one-to-one turbine, and a sharp disc tip is for the one-to-many turbine. The relative height and tip profile of the one-to-many turbine should be determined according to their effects on turbine performance, manufacturing difficulty and mechanical deformation.
Open AccessInfluence of Disc Tip Geometry on the Aerodynamic Performance and Flow Characteristics of Multichannel Tesla Turbines
As a competitive small-scale turbomachinery option, Tesla turbines have wide potential in various fields, such as renewable energy generation systems and small power equipment. This paper investigates the influence of disc tip geometry, including its profile and relative height, on the aerodynamic performance and flow characteristics of one-to-one and one-to-many multichannel Tesla turbines. The results indicate that compared to the turbine with blunt tips, the isentropic efficiency of the one-to-one turbine with sharp tips has a little decrease, which is because the relative tangential velocity gradient near the rotational disc walls decreases a little and additional vortices are generated at the rotor inlet, while that of the one-to-many turbine with sharp tips increases significantly, resulting from an increase in the relative tangential velocity in the disc channels and a decrease in the low Mach number and vortex area; for instance the turbine efficiency for the former relatively decreases by 3.6% and that for the latter increases by 13.5% at 30,000 r/min. In addition, the isentropic efficiency of the one-to-many turbine with sharp tips goes up with increasing relative height due to increasing improvement of flow status, and its increment rate slows down. A circular or elliptic tip performs better with lower relative height and a triangular tip behaves better with higher relative height. To sum up, a blunt disc tip is recommended for the one-to-one turbine, and a sharp disc tip is for the one-to-many turbine. The relative height and tip profile of the one-to-many turbine should be determined according to their effects on turbine performance, manufacturing difficulty and mechanical deformation.
- Open Access
Disc Thickness and Spacing Distance Impacts on Flow Characteristics of Multichannel Tesla Turbines
Tesla turbines are a kind of unconventional bladeless turbines, which utilize the viscosity of working fluid to rotate the rotor and realize energy conversion. They offer an attractive substitution for small and micro conventional bladed turbines due to two major advantages. In this study, the effects of two influential geometrical parameters, disc thickness and disc spacing distance, on the aerodynamic performance and flow characteristics for two kinds of multichannel Tesla turbines (one-to-one turbine and one-to-many turbine) were investigated and analyzed numerically. The results show that, with increasing disc thickness, the isentropic efficiency of the one-to-one turbine decreases a little and that of the one-to-many turbine reduces significantly. For example, for turbine cases with 0.5 mm disc spacing distance, the former drops less than 7% and the latter decreases by about 45% of their original values as disc thickness increases from 1 mm to 2 mm. With increasing disc spacing distance, the isentropic efficiency of both kinds of turbines increases first and then decreases, and an optimal value and a high efficiency range exist to make the isentropic efficiency reach its maximum and maintain at a high level, respectively. The optimal disc spacing distance for the one-to-one turbine is less than that for the one-to-many turbine (0.5 mm and 1 mm, respectively, for turbine cases with disc thickness of 1 mm). To sum up, for designing a multichannel Tesla turbine, the disc spacing distance should be among its high efficiency range, and the determination of disc thickness should be balanced between its impacts on the aerodynamic performance and mechanical stress.
Open AccessDisc Thickness and Spacing Distance Impacts on Flow Characteristics of Multichannel Tesla Turbines
Tesla turbines are a kind of unconventional bladeless turbines, which utilize the viscosity of working fluid to rotate the rotor and realize energy conversion. They offer an attractive substitution for small and micro conventional bladed turbines due to two major advantages. In this study, the effects of two influential geometrical parameters, disc thickness and disc spacing distance, on the aerodynamic performance and flow characteristics for two kinds of multichannel Tesla turbines (one-to-one turbine and one-to-many turbine) were investigated and analyzed numerically. The results show that, with increasing disc thickness, the isentropic efficiency of the one-to-one turbine decreases a little and that of the one-to-many turbine reduces significantly. For example, for turbine cases with 0.5 mm disc spacing distance, the former drops less than 7% and the latter decreases by about 45% of their original values as disc thickness increases from 1 mm to 2 mm. With increasing disc spacing distance, the isentropic efficiency of both kinds of turbines increases first and then decreases, and an optimal value and a high efficiency range exist to make the isentropic efficiency reach its maximum and maintain at a high level, respectively. The optimal disc spacing distance for the one-to-one turbine is less than that for the one-to-many turbine (0.5 mm and 1 mm, respectively, for turbine cases with disc thickness of 1 mm). To sum up, for designing a multichannel Tesla turbine, the disc spacing distance should be among its high efficiency range, and the determination of disc thickness should be balanced between its impacts on the aerodynamic performance and mechanical stress.
- Open Access
- 24 January 2016
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2016, 1-12
Shafting Alignment Computing Method of New Multibearing Rotor System under Specific Installation Requirement
The shafting of large steam turbine generator set is composed of several rotors which are connected by couplings. The computing method of shafting with different structure under specific installation requirement is studied in this paper. Based on three-moment equation, shafting alignment mathematical model is established. The computing method of bearing elevations and loads under corresponding installation requirements, where bending moment of each coupling is zero and there exist preset sag and gap in some couplings, is proposed, respectively. Bearing elevations and loads of shafting with different structure under specific installation requirement are calculated; calculation results are compared with installation data measured on site which verifies the validity and accuracy of the proposed shafting alignment computing method. The above work provides a reliable approach to analyze shafting alignment and could guide installation on site.
- 24 January 2016
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2016, 1-12
Open AccessShafting Alignment Computing Method of New Multibearing Rotor System under Specific Installation Requirement
The shafting of large steam turbine generator set is composed of several rotors which are connected by couplings. The computing method of shafting with different structure under specific installation requirement is studied in this paper. Based on three-moment equation, shafting alignment mathematical model is established. The computing method of bearing elevations and loads under corresponding installation requirements, where bending moment of each coupling is zero and there exist preset sag and gap in some couplings, is proposed, respectively. Bearing elevations and loads of shafting with different structure under specific installation requirement are calculated; calculation results are compared with installation data measured on site which verifies the validity and accuracy of the proposed shafting alignment computing method. The above work provides a reliable approach to analyze shafting alignment and could guide installation on site.
- Open Access
- 25 November 2015
- Published by Springer Nature in BioMedical Engineering OnLine
- Vol. 14 (1) , 1-19
The role of the circle of Willis in internal carotid artery stenosis and anatomical variations: a computational study based on a patient-specific three-dimensional model
The aim of this study is to provide better insights into the cerebral perfusion patterns and collateral mechanism of the circle of Willis (CoW) under anatomical and pathological variations. In the current study, a patient-specific three-dimensional computational model of the CoW was reconstructed based on the computed tomography (CT) images. The Carreau model was applied to simulate the non-Newtonian property of blood. Flow distributions in five common anatomical variations coexisting with different degrees of stenosis in the right internal carotid artery (RICA) were investigated to obtain detailed flow information. With the development of stenosis in unilateral internal carotid artery (ICA), the cerebral blood supply decreased when the degree of stenosis increased. The blood supply of the ipsilateral middle cerebral artery (MCA) was most affected by the stenosis of ICA. The anterior communicating artery (ACoA) and ipsilateral posterior communicating artery (PCoA) functioned as the important collateral circulation channels when unilateral stenosis occurred. The blood flow of the anterior circulation and the total cerebral blood flow (CBF) reached to the minimum in the configuration of the contralateral proximal anterior cerebral artery (A1) absence coexisting with unilateral ICA stenosis. Communicating arteries provided important collateral channels in the complete CoW when stenosis in unilateral ICA occurred. The cross-flow in the ACoA is a sensitive indicator of the morphological change of the ICA. The collateral function of the PCoA on the affected side will not be fully activated until a severe stenosis occurred in unilateral ICA. The absence of unilateral A1 coexisting with the stenosis in the contralateral ICA could be the most dangerous configuration in terms of the total cerebral blood supply. The findings of this study would enhance the understanding of the collateral mechanism of the CoW under different anatomical variations.
- 25 November 2015
- Published by Springer Nature in BioMedical Engineering OnLine
- Vol. 14 (1) , 1-19
Open AccessThe role of the circle of Willis in internal carotid artery stenosis and anatomical variations: a computational study based on a patient-specific three-dimensional model
The aim of this study is to provide better insights into the cerebral perfusion patterns and collateral mechanism of the circle of Willis (CoW) under anatomical and pathological variations. In the current study, a patient-specific three-dimensional computational model of the CoW was reconstructed based on the computed tomography (CT) images. The Carreau model was applied to simulate the non-Newtonian property of blood. Flow distributions in five common anatomical variations coexisting with different degrees of stenosis in the right internal carotid artery (RICA) were investigated to obtain detailed flow information. With the development of stenosis in unilateral internal carotid artery (ICA), the cerebral blood supply decreased when the degree of stenosis increased. The blood supply of the ipsilateral middle cerebral artery (MCA) was most affected by the stenosis of ICA. The anterior communicating artery (ACoA) and ipsilateral posterior communicating artery (PCoA) functioned as the important collateral circulation channels when unilateral stenosis occurred. The blood flow of the anterior circulation and the total cerebral blood flow (CBF) reached to the minimum in the configuration of the contralateral proximal anterior cerebral artery (A1) absence coexisting with unilateral ICA stenosis. Communicating arteries provided important collateral channels in the complete CoW when stenosis in unilateral ICA occurred. The cross-flow in the ACoA is a sensitive indicator of the morphological change of the ICA. The collateral function of the PCoA on the affected side will not be fully activated until a severe stenosis occurred in unilateral ICA. The absence of unilateral A1 coexisting with the stenosis in the contralateral ICA could be the most dangerous configuration in terms of the total cerebral blood supply. The findings of this study would enhance the understanding of the collateral mechanism of the CoW under different anatomical variations.
- Open Access
- 9 January 2015
- Published by Springer Nature in BioMedical Engineering OnLine
- Vol. 14 (S1) , S10
Experimental study of hemodynamics in the circle of willis
The Circle of Willis (CoW) is an important collateral pathway of the cerebral blood flow. An experimental study of the cerebral blood flow (CBF) distribution in different anatomical variations may help to a better understanding of the collateral mechanism of the CoW. An in-vitro test rig was developed to simulate the physiological cerebral blood flow in the CoW. Ten anatomical variations were considered in this study, include a set of different degrees of stenosis in L-ICA and L-ICA occlusion coexist with common anatomical variations. Volume flow rates of efferent arteries and pressure signals at the end of communicating arteries of each case were recorded. Physiological pressure waveforms were applied as inlet boundary condition. In the development of L-ICA stenosis, the total CBF decreases with the increase of stenosis degree. The blood supply of ipsilateral middle cerebral artery (MCA) was affected most by the stenosis of L-ICA. Anterior communicating artery (ACoA) and ipsilateral posterior communicating artery (PCoA) function as important collateral pathways of cerebral collateral circulation when unilateral stenosis occurred. The blood supply of anterior cerebral circulation was compensated by the posterior cerebral circulation through ipsilateral PCoA when L-ICA stenosis degree is greater than 40% and the affected side was compensated immediately by the unaffected side through ACoA. Blood flow of the anterior circulation and the total CBF reached the minimum among all cases studied when L-ICA occlusion coexist with the absence of PCoA. The results demonstrated the flow distribution patterns of the CoW under anatomical variations and clarified the collateral mechanism of the CoW. The flow ACoA is the most sensitive indexes to the morphology change of ipsilateral ICA. The relative independence of the circulation in anterior and posterior sections of the CoW is not broken and the function of ipsilateral PCoA is not activated until a severe stenosis of unilateral ICA occurs. PCoA is the most important collateral pathway of the collateral circulation and the missing of PCoA has the highest risk of stroke when the ipsilateral ICA has severe stenosis. These findings may provide the basis for future therapeutic and diagnosis applications.
- 9 January 2015
- Published by Springer Nature in BioMedical Engineering OnLine
- Vol. 14 (S1) , S10
Open AccessExperimental study of hemodynamics in the circle of willis
The Circle of Willis (CoW) is an important collateral pathway of the cerebral blood flow. An experimental study of the cerebral blood flow (CBF) distribution in different anatomical variations may help to a better understanding of the collateral mechanism of the CoW. An in-vitro test rig was developed to simulate the physiological cerebral blood flow in the CoW. Ten anatomical variations were considered in this study, include a set of different degrees of stenosis in L-ICA and L-ICA occlusion coexist with common anatomical variations. Volume flow rates of efferent arteries and pressure signals at the end of communicating arteries of each case were recorded. Physiological pressure waveforms were applied as inlet boundary condition. In the development of L-ICA stenosis, the total CBF decreases with the increase of stenosis degree. The blood supply of ipsilateral middle cerebral artery (MCA) was affected most by the stenosis of L-ICA. Anterior communicating artery (ACoA) and ipsilateral posterior communicating artery (PCoA) function as important collateral pathways of cerebral collateral circulation when unilateral stenosis occurred. The blood supply of anterior cerebral circulation was compensated by the posterior cerebral circulation through ipsilateral PCoA when L-ICA stenosis degree is greater than 40% and the affected side was compensated immediately by the unaffected side through ACoA. Blood flow of the anterior circulation and the total CBF reached the minimum among all cases studied when L-ICA occlusion coexist with the absence of PCoA. The results demonstrated the flow distribution patterns of the CoW under anatomical variations and clarified the collateral mechanism of the CoW. The flow ACoA is the most sensitive indexes to the morphology change of ipsilateral ICA. The relative independence of the circulation in anterior and posterior sections of the CoW is not broken and the function of ipsilateral PCoA is not activated until a severe stenosis of unilateral ICA occurs. PCoA is the most important collateral pathway of the collateral circulation and the missing of PCoA has the highest risk of stroke when the ipsilateral ICA has severe stenosis. These findings may provide the basis for future therapeutic and diagnosis applications.
- 15 January 2014
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 136 (2) , 021011
Nonlinear Dynamics of the Rod-Fastened Jeffcott Rotor
Rod-fastened rotors are composed of some disks clamped together by a central tie rod or several tie rods distributed along the circumference. Due to the nonlinear flexural stiffness of the contact interfaces in disks, especially when the contact surfaces are partially separated, the dynamics of the rod-fastened rotors are potentially different from that of the solid rotors. In this paper, the nonlinear flexural stiffness of a rod-fastened Jeffcott rotor is calculated by the finite element method (FEM). Then the harmonic balance method is adopted to analyze the dynamics of the rotor. The flexural stiffness of a rod-fastened Jeffcott rotor dramatically decreased with the increase of the dimensionless load γ1 from 1 to 2.5. Thus, the dynamics of the rotor were nonlinear when it was subjected to a large unbalance force. The response of the rotating rotor contains a predominantly forward 1X component or both forward 1X component and backward 1X components. However, the rotor may settle in a state depending upon both the operating parameters and its history.
- 15 January 2014
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 136 (2) , 021011
Nonlinear Dynamics of the Rod-Fastened Jeffcott Rotor
Rod-fastened rotors are composed of some disks clamped together by a central tie rod or several tie rods distributed along the circumference. Due to the nonlinear flexural stiffness of the contact interfaces in disks, especially when the contact surfaces are partially separated, the dynamics of the rod-fastened rotors are potentially different from that of the solid rotors. In this paper, the nonlinear flexural stiffness of a rod-fastened Jeffcott rotor is calculated by the finite element method (FEM). Then the harmonic balance method is adopted to analyze the dynamics of the rotor. The flexural stiffness of a rod-fastened Jeffcott rotor dramatically decreased with the increase of the dimensionless load γ1 from 1 to 2.5. Thus, the dynamics of the rotor were nonlinear when it was subjected to a large unbalance force. The response of the rotating rotor contains a predominantly forward 1X component or both forward 1X component and backward 1X components. However, the rotor may settle in a state depending upon both the operating parameters and its history.