DLDaw-Kwei Leu
Daw-Kwei Leu
*This is an algorithmically generated author record based on publicly available information.
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Latest Publications
- 1 March 2012
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 64 (1-4) , 93-103
Position deviation in V-die bending process with asymmetric bend length
- 1 March 2012
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 64 (1-4) , 93-103
Position deviation in V-die bending process with asymmetric bend length
- 1 June 2011
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 25 (6) , 1509-1517
Evaluation of friction coefficient using indentation model of Brinell hardness test for sheet metal forming
- 1 June 2011
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 25 (6) , 1509-1517
Evaluation of friction coefficient using indentation model of Brinell hardness test for sheet metal forming
- 20 April 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 57 (5-8) , 575-584
Modeling of surface roughness effect on dry contact friction in metal forming
- 20 April 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 57 (5-8) , 575-584
Modeling of surface roughness effect on dry contact friction in metal forming
- 5 August 2010
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 24 (8) , 1697-1707
Evaluation of friction coefficient using simplified deformation model of plastic hemispherical contact with a rigid flat
- 5 August 2010
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 24 (8) , 1697-1707
Evaluation of friction coefficient using simplified deformation model of plastic hemispherical contact with a rigid flat
- 11 December 2008
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 131 (1) , 011002
Modeling of Size Effect on Tensile Flow Stress of Sheet Metal in Microforming
This investigation considers the size effect on the deformation behavior of simple tension in microforming and thus proposes a simple model of the tensile flow stress of sheet metal. Experimental results reveal that the measure of the flow stress can be represented as a hyperbolic function , which is a function of (sheet thickness/grain size). The predicted flow stress agrees very well with the published experiment. Notably, a specimen with smaller grains has lower normalized flow stress for a given . Since the material properties of the macroscale specimen do not pertain to the microscale, a critical condition that distinguishes the macroscale from the microscale in the tensile flow stress is subsequently proposed, based on the “affected zone” model, the pile-up theory of dislocations, and the Hall–Petch relation. The distribution of the predicted is similar to the experimental finding that the decreases as the grain size increases. However, the orientation-dependent factor is sensitive to . Hence, further study of the orientation-dependent factor is necessary to obtain a more accurate and, thus, to evaluate and understand better the tensile flow stress of sheet metal in microforming.- 11 December 2008
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 131 (1) , 011002
Modeling of Size Effect on Tensile Flow Stress of Sheet Metal in Microforming
This investigation considers the size effect on the deformation behavior of simple tension in microforming and thus proposes a simple model of the tensile flow stress of sheet metal. Experimental results reveal that the measure of the flow stress can be represented as a hyperbolic function , which is a function of (sheet thickness/grain size). The predicted flow stress agrees very well with the published experiment. Notably, a specimen with smaller grains has lower normalized flow stress for a given . Since the material properties of the macroscale specimen do not pertain to the microscale, a critical condition that distinguishes the macroscale from the microscale in the tensile flow stress is subsequently proposed, based on the “affected zone” model, the pile-up theory of dislocations, and the Hall–Petch relation. The distribution of the predicted is similar to the experimental finding that the decreases as the grain size increases. However, the orientation-dependent factor is sensitive to . Hence, further study of the orientation-dependent factor is necessary to obtain a more accurate and, thus, to evaluate and understand better the tensile flow stress of sheet metal in microforming.