David Lane Tomasko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
David Lane Tomasko has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Hrishikesh Ramesh Munj
Department of Chemical and Biomolecular Engineering, Ohio State University, Columbus, Ohio, 43210
1 shared publication- John A. Merrill
First-Year Engineering Program Director, College of Engineering, The Ohio State University
1 shared publication John Joseph Lannutti
Materials Science and Engineering Ohio State University Columbus Ohio 43210
1 shared publication- Ly James Lee
Department of Chemical and Biomolecular Engineering, The Ohio State University, Columbus, OH, 43210, USA
1 shared publication M. Tyler Nelson
Department of Biomedical Engineering Ohio State University Columbus Ohio 43210
1 shared publication- Paul A. Clingan
Lecturer, College of Engineering, The Ohio State University
1 shared publication
Latest Publications
- 6 March 2014
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 102 (7) , 1517-1527
Biocompatible electrospun polymer blends for biomedical applications
Blends of natural and synthetic polymers have received considerable attention as biomaterials due to the potential to optimize both mechanical and bioactive properties. Electrospinning of biocompatible polymers is an efficient method producing biomimetic topographies suited to various applications. In the ultimate application, electrospun scaffolds must also incorporate drug/protein delivery for effective cell growth and tissue repair. This study explored the suitability of a ternary Polymethylmethacrylate‐Polycaprolactone‐gelatin blend in the preparation of electrospun scaffolds for biomedical applications. Tuning the blend composition allows control over scaffold mechanical properties and degradation rate. Significant improvements were observed in the mechanical properties of the blend compared with the individual components. In order to study drug delivery potential, triblends were impregnated with the model compound Rhodamine‐B using sub/supercritical CO2infusion under benign conditions. Results show significantly distinct release profiles of the impregnated dye from the triblends. Specific factors such as porosity, degradation rate, stress relaxation, dye‐polymer interactions, play key roles in impregnation and release. Each polymer component of the triblends shows distinct behavior during impregnation and release process. This affects the aforementioned factors and the release profiles of the dye. Careful control over blend composition and infusion conditions creates the flexibility needed to produce biocompatible electrospun scaffolds for a variety of biomedical applications. © 2014 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 102B: 1517–1527, 2014.
- 6 March 2014
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 102 (7) , 1517-1527
Biocompatible electrospun polymer blends for biomedical applications
Blends of natural and synthetic polymers have received considerable attention as biomaterials due to the potential to optimize both mechanical and bioactive properties. Electrospinning of biocompatible polymers is an efficient method producing biomimetic topographies suited to various applications. In the ultimate application, electrospun scaffolds must also incorporate drug/protein delivery for effective cell growth and tissue repair. This study explored the suitability of a ternary Polymethylmethacrylate‐Polycaprolactone‐gelatin blend in the preparation of electrospun scaffolds for biomedical applications. Tuning the blend composition allows control over scaffold mechanical properties and degradation rate. Significant improvements were observed in the mechanical properties of the blend compared with the individual components. In order to study drug delivery potential, triblends were impregnated with the model compound Rhodamine‐B using sub/supercritical CO2infusion under benign conditions. Results show significantly distinct release profiles of the impregnated dye from the triblends. Specific factors such as porosity, degradation rate, stress relaxation, dye‐polymer interactions, play key roles in impregnation and release. Each polymer component of the triblends shows distinct behavior during impregnation and release process. This affects the aforementioned factors and the release profiles of the dye. Careful control over blend composition and infusion conditions creates the flexibility needed to produce biocompatible electrospun scaffolds for a variety of biomedical applications. © 2014 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 102B: 1517–1527, 2014.
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 10-11
Work in Progress: Micro-/Nano-technology `Lab-on-a-chip' Research Project for First-Year Honors Engineering Program
The Fundamentals of Engineering for Honors (FEH) alternate group project (ENG H193A) uses micro-and nano-technology to involve students in research in their first year through development of and experimentation with a silicone rubber 'lab-on-a-chip'. Students seek to determine if a correlation exists between surface topology and cell adherence. They design and fabricate a lab-on-a-chip and use it to test the hypothesis. As part of the project, students use computational fluid dynamics (CFD) software to better understand and visualize the forces acting on the cells. Additionally, students create a three-dimensional computer-aided model of a theoretical nanofactory which would be used to alter the structure of DNA. At the end of the term, students submit a written report, project notebook, and laboratory notebook detailing their experimental work as well as their nanofactory model. Finally, they present the results of their experimental work orally to a panel who judge the students' results and understanding of the concepts involved
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 10-11
Work in Progress: Micro-/Nano-technology `Lab-on-a-chip' Research Project for First-Year Honors Engineering Program
The Fundamentals of Engineering for Honors (FEH) alternate group project (ENG H193A) uses micro-and nano-technology to involve students in research in their first year through development of and experimentation with a silicone rubber 'lab-on-a-chip'. Students seek to determine if a correlation exists between surface topology and cell adherence. They design and fabricate a lab-on-a-chip and use it to test the hypothesis. As part of the project, students use computational fluid dynamics (CFD) software to better understand and visualize the forces acting on the cells. Additionally, students create a three-dimensional computer-aided model of a theoretical nanofactory which would be used to alter the structure of DNA. At the end of the term, students submit a written report, project notebook, and laboratory notebook detailing their experimental work as well as their nanofactory model. Finally, they present the results of their experimental work orally to a panel who judge the students' results and understanding of the concepts involved
- 14 June 2005
- Published by CSIRO Publishing in Australian Journal of Chemistry
- Vol. 58 (6) , 492-503
CO2 Foaming of Polymer Nanocomposite Blends
Nanoparticles are suitable to nucleate small foam cells and simultaneously reinforce the thin foam cell walls. In this paper, it is found that the foam morphology and the physical properties are greatly influenced by the dispersion of nanoclay, the clay surface modification, and the nanocomposite blend morphology. The addition of nanoclay to polystyrene (PS) strongly affects the nucleation of foam bubbles, especially after exfoliation and proper surface modification. CO2 appears to nucleate on the solid clay surface with a CO2-affinitive surface modifier. PS/(PMMA/MHABS) nanocomposite blends composed of polystyrene and poly(methyl methacrylate)/nanoclay exfoliated nanocomposite show an unexpected trend that bubble nucleation inversely correlates with domain size, where the bigger PMMA/MHABS domains are significant in nucleating more bubbles. The total influence volume, formed by the CO2 diffusion from the PMMA/MHABS phase to the PS phase where CO2 concentration decreases from a high value in the former to a low value in the latter, is related to the domain size and determines the nucleation efficiency in the PS phase. The physical properties of PS nanocomposites exhibit unique behaviour in the presence of CO2.
- 14 June 2005
- Published by CSIRO Publishing in Australian Journal of Chemistry
- Vol. 58 (6) , 492-503
CO2 Foaming of Polymer Nanocomposite Blends
Nanoparticles are suitable to nucleate small foam cells and simultaneously reinforce the thin foam cell walls. In this paper, it is found that the foam morphology and the physical properties are greatly influenced by the dispersion of nanoclay, the clay surface modification, and the nanocomposite blend morphology. The addition of nanoclay to polystyrene (PS) strongly affects the nucleation of foam bubbles, especially after exfoliation and proper surface modification. CO2 appears to nucleate on the solid clay surface with a CO2-affinitive surface modifier. PS/(PMMA/MHABS) nanocomposite blends composed of polystyrene and poly(methyl methacrylate)/nanoclay exfoliated nanocomposite show an unexpected trend that bubble nucleation inversely correlates with domain size, where the bigger PMMA/MHABS domains are significant in nucleating more bubbles. The total influence volume, formed by the CO2 diffusion from the PMMA/MHABS phase to the PS phase where CO2 concentration decreases from a high value in the former to a low value in the latter, is related to the domain size and determines the nucleation efficiency in the PS phase. The physical properties of PS nanocomposites exhibit unique behaviour in the presence of CO2.