Ki-Yong Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ki-Yong Lee has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Do-Sik Shim
Department of Ocean Advanced Materials Convergence Engineering, Korea Maritime and Ocean University, Busan, Republic of Korea
8 shared publications - Gwang Yong Shin
Automotive Materials & Components R&D Group, Korea Institute of Industrial Technology, Gwangju, Republic of Korea
4 shared publications - Chang-Hwan Choi
Department of Mechanical Engineering, Stevens Institute of Technology, Castle Point on Hudson, Hoboken, NJ 07030, USA
2 shared publications Gyeong Yun Baek
Chonnam Natl Univ, Dept Mech Engn, Gwangju 61186, South Korea
2 shared publications- Gyeong Yun Baek
Smart Manufacturing Process Technology Group, Korea Institute of Industrial Technology, 9 Cheonmdan-Venturero 108beon-gil, Buk-gu, Gwangju 61007, Korea
2 shared publications - Jong-Youn Son
Department of Mechanical Engineering, Stevens Institute of Technology, Castle Point on Hudson, Hoboken, NJ 07030, USA
2 shared publications
Latest Publications
- Open Access
- 6 February 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (2) , 243
Effects of Oxidized Metal Powders on Pore Defects in Powder-Fed Direct Energy Deposition
Laser-based additive manufacturing processes, particularly direct energy deposition (DED), have gained prominence for fabricating complex, functionally graded, or customized parts. DED employs a high-powered heat source to melt metallic powder or wire, enabling precise control of grain structures and the production of high-strength objects. However, common defects, such as a lack of fusion and pores between layers or beads, can compromise the mechanical properties of the printed components. This study focuses on investigating the recurrent causes of pore defects in the powder-fed DED process, with a specific emphasis on the influence of oxidized metal powders. This research explores the impact of intentionally oxidizing metal powders of hot work tool steel H13 by exposing them to regulated humidity and temperature conditions. Scanning electron microscopy images and energy-dispersive X-ray spectroscopy results demonstrate the clumping of powders and the deposition of iron oxides in the oxidized powders at elevated temperatures (70 °C for 72 h). Multi-layered depositions of the oxidized H13 powders on STD61 substrate do not show significant differences in cross sections among specimens, suggesting that oxidation does not visibly form large pores. However, fine pores, detected through CT scanning, are observed in depositions of oxidized powders at higher temperatures. These fine pores, typically less than 250 µm in diameter, are irregularly distributed throughout the deposition, indicating a potential degradation in mechanical properties. The findings highlight the need for careful consideration of oxidation effects in optimizing process parameters for enhanced additive manufacturing quality.
- 6 February 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (2) , 243
Open AccessEffects of Oxidized Metal Powders on Pore Defects in Powder-Fed Direct Energy Deposition
Laser-based additive manufacturing processes, particularly direct energy deposition (DED), have gained prominence for fabricating complex, functionally graded, or customized parts. DED employs a high-powered heat source to melt metallic powder or wire, enabling precise control of grain structures and the production of high-strength objects. However, common defects, such as a lack of fusion and pores between layers or beads, can compromise the mechanical properties of the printed components. This study focuses on investigating the recurrent causes of pore defects in the powder-fed DED process, with a specific emphasis on the influence of oxidized metal powders. This research explores the impact of intentionally oxidizing metal powders of hot work tool steel H13 by exposing them to regulated humidity and temperature conditions. Scanning electron microscopy images and energy-dispersive X-ray spectroscopy results demonstrate the clumping of powders and the deposition of iron oxides in the oxidized powders at elevated temperatures (70 °C for 72 h). Multi-layered depositions of the oxidized H13 powders on STD61 substrate do not show significant differences in cross sections among specimens, suggesting that oxidation does not visibly form large pores. However, fine pores, detected through CT scanning, are observed in depositions of oxidized powders at higher temperatures. These fine pores, typically less than 250 µm in diameter, are irregularly distributed throughout the deposition, indicating a potential degradation in mechanical properties. The findings highlight the need for careful consideration of oxidation effects in optimizing process parameters for enhanced additive manufacturing quality.
- Open Access
- 18 April 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (4) , 872
Mechanical and Thermal Properties of the High Thermal Conductivity Steel (HTCS) Additively Manufactured via Powder-Fed Direct Energy Deposition
High thermal conductivity steel (HTCS-150) is deposited onto non-heat-treated AISI H13 (N-H13) via powder-fed direct energy deposition (DED) based on the response surface methodology (RSM) to enhance the mechanical properties and thermal conductivity of N-H13, which is generally used as a hot-work tool steel. The main process parameters of the powder-fed DED are priorly optimized to minimize defects in the deposited regions and, therefore, to obtain homogeneous material properties. The deposited HTCS-150 is comprehensively evaluated through hardness, tensile, and wear tests at the different temperatures of 25, 200, 400, 600, and 800 °C. Compared to conventionally heat-treated (quenched and tempered) H13 (HT-H13), the hardness of the additively manufactured HTCS-150 slightly increases at 25 °C, whereas it does not show any significant difference above 200 °C. However, the HTCS-150 deposited on N-H13 shows a lower ultimate tensile strength and elongation than HT-H13 at all tested temperatures, and the deposition of the HTCS-150 on N-H13 enhances the ultimate tensile strength of N-H13. While the HTCS-150 does not show a significant difference in the wear rate below 400 °C compared to HT-H13, it shows a lower wear rate above 600 °C. The HTCS-150 reveals a higher thermal conductivity than the HT-H13 below 600 °C, whereas the behavior is reversed at 800 °C. The results suggest that the HTCS-150 additively manufactured via powder-fed direct energy deposition can enhance the mechanical and thermal properties of N-H13, including hardness, tensile strength, wear resistance, and thermal conductivity in a wide range of temperatures, often superior to those of HT-H13.
- 18 April 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (4) , 872
Open AccessMechanical and Thermal Properties of the High Thermal Conductivity Steel (HTCS) Additively Manufactured via Powder-Fed Direct Energy Deposition
High thermal conductivity steel (HTCS-150) is deposited onto non-heat-treated AISI H13 (N-H13) via powder-fed direct energy deposition (DED) based on the response surface methodology (RSM) to enhance the mechanical properties and thermal conductivity of N-H13, which is generally used as a hot-work tool steel. The main process parameters of the powder-fed DED are priorly optimized to minimize defects in the deposited regions and, therefore, to obtain homogeneous material properties. The deposited HTCS-150 is comprehensively evaluated through hardness, tensile, and wear tests at the different temperatures of 25, 200, 400, 600, and 800 °C. Compared to conventionally heat-treated (quenched and tempered) H13 (HT-H13), the hardness of the additively manufactured HTCS-150 slightly increases at 25 °C, whereas it does not show any significant difference above 200 °C. However, the HTCS-150 deposited on N-H13 shows a lower ultimate tensile strength and elongation than HT-H13 at all tested temperatures, and the deposition of the HTCS-150 on N-H13 enhances the ultimate tensile strength of N-H13. While the HTCS-150 does not show a significant difference in the wear rate below 400 °C compared to HT-H13, it shows a lower wear rate above 600 °C. The HTCS-150 reveals a higher thermal conductivity than the HT-H13 below 600 °C, whereas the behavior is reversed at 800 °C. The results suggest that the HTCS-150 additively manufactured via powder-fed direct energy deposition can enhance the mechanical and thermal properties of N-H13, including hardness, tensile strength, wear resistance, and thermal conductivity in a wide range of temperatures, often superior to those of HT-H13.
- 31 January 2023
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing-Green Technology
- Vol. 10 (6) , 1579-1604
Adhesion with Aluminum for Material Surfaces Additively Manufactured by Directed Energy Deposition
- 31 January 2023
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing-Green Technology
- Vol. 10 (6) , 1579-1604
Adhesion with Aluminum for Material Surfaces Additively Manufactured by Directed Energy Deposition
- Open Access
Effect of Post-Heat Treatment on the AISI M4 Layer Deposited by Directed Energy Deposition
Currently, high-speed steel (HSS) powders are deposited locally on a metal surface through direct energy deposition (DED) onto hardface tool steel. Although the HSS powder enhances the hardness and the abrasion resistance of a metal surface, it makes the tool steel brittle because of its high carbon content. In addition, the steel is likely to break when subjected to a high load over time. This study focused on improving the steel toughness by applying a post-heat treatment. To fabricate a uniformly deposited layer through DED, M4 powder was deposited onto a pre-heated substrate (AISI D2). In addition, four post-heat-treated specimens were prepared, and their mechanical properties were compared. The Charpy impact and hardness tests were conducted to evaluate the durability required for the D2 die. The deposited M4 powder possessed a high hardness but a relatively low impact toughness. During laser melting, a stable bond formed between M4 and D2 without any cracks or delamination. The hardness of the initial M4 deposited layer was 63 HRC, which changed to 54–63 HRC depending on the effect of the post-heat treatment. Moreover, the post-heat-treatment process improves the impact toughness of the M4 deposited layer by changing its microstructure.
Open AccessEffect of Post-Heat Treatment on the AISI M4 Layer Deposited by Directed Energy Deposition
Currently, high-speed steel (HSS) powders are deposited locally on a metal surface through direct energy deposition (DED) onto hardface tool steel. Although the HSS powder enhances the hardness and the abrasion resistance of a metal surface, it makes the tool steel brittle because of its high carbon content. In addition, the steel is likely to break when subjected to a high load over time. This study focused on improving the steel toughness by applying a post-heat treatment. To fabricate a uniformly deposited layer through DED, M4 powder was deposited onto a pre-heated substrate (AISI D2). In addition, four post-heat-treated specimens were prepared, and their mechanical properties were compared. The Charpy impact and hardness tests were conducted to evaluate the durability required for the D2 die. The deposited M4 powder possessed a high hardness but a relatively low impact toughness. During laser melting, a stable bond formed between M4 and D2 without any cracks or delamination. The hardness of the initial M4 deposited layer was 63 HRC, which changed to 54–63 HRC depending on the effect of the post-heat treatment. Moreover, the post-heat-treatment process improves the impact toughness of the M4 deposited layer by changing its microstructure.
- Open Access
Mechanical Properties of Tool Steels with High Wear Resistance via Directed Energy Deposition
This study focused on the mechanical and metallurgical characteristics of high-wear-resistance steel (HWS) deposited using directed energy deposition (DED) for metal substrate hardfacing or repairing. As post-deposition heat treatment changes the metallurgical characteristics of deposits, the effect of post-deposition heat treatment on the mechanical properties was investigated via microstructure observation and by conducting hardness, wear, and impact tests. The obtained micro-images showed that the deposited HWS layers exhibit cellular and columnar dendrites, and the microstructure of heat-treated HWS (HT-HWS) transformed its phase during quenching and tempering. The hardness and wear resistance of the HT-HWS deposits were higher than those of the HWS deposited specimen, whereas the latter exhibited a higher fracture toughness. The matrix microstructure and carbide characteristics, which are characterized by the chemical composition of the materials, significantly influenced the mechanical properties.
Open AccessMechanical Properties of Tool Steels with High Wear Resistance via Directed Energy Deposition
This study focused on the mechanical and metallurgical characteristics of high-wear-resistance steel (HWS) deposited using directed energy deposition (DED) for metal substrate hardfacing or repairing. As post-deposition heat treatment changes the metallurgical characteristics of deposits, the effect of post-deposition heat treatment on the mechanical properties was investigated via microstructure observation and by conducting hardness, wear, and impact tests. The obtained micro-images showed that the deposited HWS layers exhibit cellular and columnar dendrites, and the microstructure of heat-treated HWS (HT-HWS) transformed its phase during quenching and tempering. The hardness and wear resistance of the HT-HWS deposits were higher than those of the HWS deposited specimen, whereas the latter exhibited a higher fracture toughness. The matrix microstructure and carbide characteristics, which are characterized by the chemical composition of the materials, significantly influenced the mechanical properties.
- Open Access
- 5 June 2018
- Published by The Korean Institute of Metals and Materials in Korean Journal of Metals and Materials
- Vol. 56 (6) , 430-439
A Study on Micro-Structure and Wear Behavior of AISI M4 and CPM15V Deposited by Laser Melting
- 5 June 2018
- Published by The Korean Institute of Metals and Materials in Korean Journal of Metals and Materials
- Vol. 56 (6) , 430-439
Open AccessA Study on Micro-Structure and Wear Behavior of AISI M4 and CPM15V Deposited by Laser Melting
- 1 January 2018
- Published by Elsevier in Optics & Laser Technology
- Vol. 98, 326-338
Effects of process parameters on properties of porous foams formed by laser-assisted melting of steel powder (AISI P21)/foaming agent (ZrH 2 ) mixture
- 1 January 2018
- Published by Elsevier in Optics & Laser Technology
- Vol. 98, 326-338
Effects of process parameters on properties of porous foams formed by laser-assisted melting of steel powder (AISI P21)/foaming agent (ZrH 2 ) mixture
- 18 October 2017
- Published by Springer Nature in Metals and Materials International
- Vol. 23 (6) , 1204-1215
Effects of substrate preheating during direct energy deposition on microstructure, hardness, tensile strength, and notch toughness
- 18 October 2017
- Published by Springer Nature in Metals and Materials International
- Vol. 23 (6) , 1204-1215
Effects of substrate preheating during direct energy deposition on microstructure, hardness, tensile strength, and notch toughness