Günter Hommel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Günter Hommel has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Konstantin Kondak
Technische Universität Berlin
7 shared publications - Andreas Wege
Institute of Computer Engineering and Microelectronics, Technical University of Berlin, Berlin, Germany
3 shared publications - Christian Fleischer
Technische Universität Berlin
3 shared publications - Dietmar Tutsch
Technische Universität Berlin
2 shared publications - Marek Musial
Technische Universität Berlin
2 shared publications - Markus Bernard
Technische Universität Berlin
2 shared publications
Latest Publications
- 1 March 2010
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 114 (1153) , 191-198
Load transportation system based on autonomous small size helicopters
This paper is devoted to modelling and control algorithms for a slung load transportation system composed of one or multiple helicopters, where the load is coupled by the means of flexible ropes (see Fig. 1). The coupled helicopter system overcomes the payload limitation of a single small size helicopter, while keeping most of its advantages: small costs of operation, low maintenance costs and increased safeness. Therefore, the system can be utilised whenever the use of full size helicopters is impossible, too expensive or prohibited by law. We focus on the deployment and repairing of distributed sensor networks, using a transportation system based on multiple small size helicopters. A possible real world application is the deployment of fire fighting equipment, where space limitation of the fire trucks prohibits the application of bigger UAVs and using full size helicopters is too dangerous. The problem of load transportation using one or two full size helicopters (twin lift helicopter system), connected to the load by means of flexible ropes, has been discussed in the aerospace research community at least since 1960. We have shown in our previous work that there is a fundamental difference in the mathematical description between small and full size helicopters. Therefore, also the control design for the case of small size helicopters needs to be different. To our knowledge, the control of a slung load transportation system composed of multiple small size helicopters has not been studied until now. In this paper, the complete mechanical setup of the slung load transportation system based on one or more small size helicopters is presented. This includes a short description of the used UAVs, the additionally required sensors, and how the load is mounted. A model of one/multiple helicopters transporting a load is introduced. This model is used in a simplified form for the controller design and in full form for simulation. The controller for one and two helicopters, which is based on a state feedback controller, as well as the controller for three and more helicopters, which is based on a non linear controller, are explained in detail. Both controllers utilise an underlying non-linear orientation controller. We propose a feedback loop, based on forces measured in the ropes, to compensate for the influence of the rope. The controllers were tested in simulation and in real flight experiments. The world wide first flight experiment with three coupled helicopters was successfully conducted at the end of 2007.
- 1 March 2010
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 114 (1153) , 191-198
Load transportation system based on autonomous small size helicopters
This paper is devoted to modelling and control algorithms for a slung load transportation system composed of one or multiple helicopters, where the load is coupled by the means of flexible ropes (see Fig. 1). The coupled helicopter system overcomes the payload limitation of a single small size helicopter, while keeping most of its advantages: small costs of operation, low maintenance costs and increased safeness. Therefore, the system can be utilised whenever the use of full size helicopters is impossible, too expensive or prohibited by law. We focus on the deployment and repairing of distributed sensor networks, using a transportation system based on multiple small size helicopters. A possible real world application is the deployment of fire fighting equipment, where space limitation of the fire trucks prohibits the application of bigger UAVs and using full size helicopters is too dangerous. The problem of load transportation using one or two full size helicopters (twin lift helicopter system), connected to the load by means of flexible ropes, has been discussed in the aerospace research community at least since 1960. We have shown in our previous work that there is a fundamental difference in the mathematical description between small and full size helicopters. Therefore, also the control design for the case of small size helicopters needs to be different. To our knowledge, the control of a slung load transportation system composed of multiple small size helicopters has not been studied until now. In this paper, the complete mechanical setup of the slung load transportation system based on one or more small size helicopters is presented. This includes a short description of the used UAVs, the additionally required sensors, and how the load is mounted. A model of one/multiple helicopters transporting a load is introduced. This model is used in a simplified form for the controller design and in full form for simulation. The controller for one and two helicopters, which is based on a state feedback controller, as well as the controller for three and more helicopters, which is based on a non linear controller, are explained in detail. Both controllers utilise an underlying non-linear orientation controller. We propose a feedback loop, based on forces measured in the ropes, to compensate for the influence of the rope. The controllers were tested in simulation and in real flight experiments. The world wide first flight experiment with three coupled helicopters was successfully conducted at the end of 2007.
- 1 January 2008
- Published by Springer Nature
- p. 49-61
A Slung Load Transportation System Based on Small Size Helicopters
- 1 January 2008
- Published by Springer Nature
- p. 49-61
A Slung Load Transportation System Based on Small Size Helicopters
- 5 November 2007
- Published by Springer Nature
- p. 193-210
Performance Models for a Hybrid Reactor System
- 1 April 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Proceedings 2001 ICRA. IEEE International Conference on Robotics and Automation (cat. No.01ch37164)
- No. 10504729,p. 2514-2519
Calibration of an EMG-Based Body Model with six Muscles to control a Leg Exoskeleton
This paper presents a body model of intermediate level of detail to allow prediction of the knee torque produced by thigh muscles based on EMG signals. This torque prediction is used as input for a torque controller that adapts the level of support offered to an operator by a powered leg orthosis. The level of detail of the body model is chosen in such a way, that all parameters of the model can be calibrated for a specific operator with only a few sensors that are mounted on the exoskeleton.
- 1 April 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Proceedings 2001 ICRA. IEEE International Conference on Robotics and Automation (cat. No.01ch37164)
- No. 10504729,p. 2514-2519
Calibration of an EMG-Based Body Model with six Muscles to control a Leg Exoskeleton
This paper presents a body model of intermediate level of detail to allow prediction of the knee torque produced by thigh muscles based on EMG signals. This torque prediction is used as input for a torque controller that adapts the level of support offered to an operator by a powered leg orthosis. The level of detail of the body model is chosen in such a way, that all parameters of the model can be calibrated for a specific operator with only a few sensors that are mounted on the exoskeleton.
- 1 October 2006
- Published by Springer Nature
- p. 149-157
Development and Control of a Hand Exoskeleton for Rehabilitation
- 1 October 2006
- Published by Springer Nature
- p. 149-157
Development and Control of a Hand Exoskeleton for Rehabilitation
- 1 October 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21530858,p. 4615-4620
Force Control Strategy for a Hand Exoskeleton Based on Sliding Mode Position Control
This paper presents a force-based control mode for a hand exoskeleton. This device has been developed with focus on support of the rehabilitation process after hand injuries or strokes. As the device is designed for the later use on patients, which have limited hand mobility, fast undesired movements have to be averted. Safety precautions in the hardware and software design of the system must be taken to ensure this. The construction allows controlling motions of the finger joints. However, due to friction in gears and mechanical construction, it is not possible to move finger joints within the construction without help of actuators. Therefore force sensors are integrated into the construction to sense force exchanged between human and exoskeleton. These allow the human to control the movements of the hand exoskeleton, which is useful to teach new trajectories or can be used for diagnostic purposes. The force control scheme presented in this paper uses the force sensor values to generate a trajectory which is executed by a position control loop based on sliding mode control
- 1 October 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21530858,p. 4615-4620
Force Control Strategy for a Hand Exoskeleton Based on Sliding Mode Position Control
This paper presents a force-based control mode for a hand exoskeleton. This device has been developed with focus on support of the rehabilitation process after hand injuries or strokes. As the device is designed for the later use on patients, which have limited hand mobility, fast undesired movements have to be averted. Safety precautions in the hardware and software design of the system must be taken to ensure this. The construction allows controlling motions of the finger joints. However, due to friction in gears and mechanical construction, it is not possible to move finger joints within the construction without help of actuators. Therefore force sensors are integrated into the construction to sense force exchanged between human and exoskeleton. These allow the human to control the movements of the hand exoskeleton, which is useful to teach new trajectories or can be used for diagnostic purposes. The force control scheme presented in this paper uses the force sensor values to generate a trajectory which is executed by a position control loop based on sliding mode control
- 1 January 2006
- Published by Springer Nature
- p. 53-62
High Performance Low Cost Multicore NoC Architectures for Embedded Systems
- 1 January 2006
- Published by Springer Nature
- p. 53-62
High Performance Low Cost Multicore NoC Architectures for Embedded Systems
- 1 January 2006
- Published by Springer Nature
- p. 177-185
Embedded Control System for a Powered Leg Exoskeleton
- 1 January 2006
- Published by Springer Nature
- p. 177-185
Embedded Control System for a Powered Leg Exoskeleton