Indranil Brahma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Indranil Brahma has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
J N Chi
Duke University, Durham, NC, USA
2 shared publicationsBenedict Vergara
George Washington University Washington, DC, USA
1 shared publicationOdinmma Ofili
Department of Mechanical Engineering, Bucknell University, Lewisburg, USA
1 shared publicationSaniya LeBlanc
George Washington University Washington, DC, USA
1 shared publicationSatbir Singh
1 shared publicationTyler Wyka
George Washington University Washington, DC, USA
1 shared publication
Latest Publications
- 19 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment
Model development of a gas turbine powered ship for comparison of green fuels
Knowledge of the effects of low/zero carbon green fuels on the performance of marine gas turbine-based propulsion systems is necessary for the decarbonization of gas-turbine powered ships. This work presents a general methodology to model an aeroderivative gas turbine-based marine propulsion system with some unique features. The gas turbine model is derived from a systematic search of discrete points of high-resolution component maps. Genetic algorithms (GA) have been used to auto-scale generic component maps to the known design point. This enables iterative re-scaling to calibrate parasitic losses and to optimize map selection. The gas turbine model is coupled to a data-based drive train/propeller model and emission model to predict ship speed and CO/CO 2 /NO x emissions for any given fuel flow rate. The integrated model was used to predict the performance of an Arleigh Burke class (DDG 51) destroyer over a 200 h, 2548 nautical mile trajectory with four different fuels: F76 Marine diesel, Liquid Hydrogen, Methanol and Liquefied Natural Gas. Predicted energy per mile and ship range were largely dependent on the tradeoff between energy density and gravimetric density of the fuels. The integrated model and aggregated data is publicly available and can be a useful tool to analyze or design marine decarbonization technologies.
- 19 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment
Model development of a gas turbine powered ship for comparison of green fuels
Knowledge of the effects of low/zero carbon green fuels on the performance of marine gas turbine-based propulsion systems is necessary for the decarbonization of gas-turbine powered ships. This work presents a general methodology to model an aeroderivative gas turbine-based marine propulsion system with some unique features. The gas turbine model is derived from a systematic search of discrete points of high-resolution component maps. Genetic algorithms (GA) have been used to auto-scale generic component maps to the known design point. This enables iterative re-scaling to calibrate parasitic losses and to optimize map selection. The gas turbine model is coupled to a data-based drive train/propeller model and emission model to predict ship speed and CO/CO 2 /NO x emissions for any given fuel flow rate. The integrated model was used to predict the performance of an Arleigh Burke class (DDG 51) destroyer over a 200 h, 2548 nautical mile trajectory with four different fuels: F76 Marine diesel, Liquid Hydrogen, Methanol and Liquefied Natural Gas. Predicted energy per mile and ship range were largely dependent on the tradeoff between energy density and gravimetric density of the fuels. The integrated model and aggregated data is publicly available and can be a useful tool to analyze or design marine decarbonization technologies.
- 29 October 2023
- Published by Elsevier in Measurement
- Vol. 223
Using Long Short-Term Memory (LSTM) networks with the toy model concept for compressible pulsatile flow metering
- 29 October 2023
- Published by Elsevier in Measurement
- Vol. 223
Using Long Short-Term Memory (LSTM) networks with the toy model concept for compressible pulsatile flow metering
- 19 July 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 29 (59) , 89449-89468
Nucleation-accumulation mode trade-off in non-volatile particle emissions from a small non-road small diesel engine
Small (< 8 kW) non-road engines are a significant source of pollutants such as particle number (PN) emissions. Many small non-road engines do not have diesel particulate filters (DPFs). They are so designed that air–fuel ratio (AFR) can be adjusted to control visible diesel smoke and particulate matter (PM) resulting from larger accumulation mode particles. However, the effect of AFR variation on smaller nucleation mode nanoparticle emissions is not well understood. Several studies on larger engines have reported a trade-off between smaller and larger particles. In this study, AFR was independently varied over the entire engine map of a naturally aspirated (NA) non-road small diesel engine using forced induction (FI) of externally compressed air. AFR’s ranged from 57 to 239 compared to the design range of 23–92 for the engine, including unusually high AFR’s at full-load operation, not previously reported for conventional combustion. As expected, larger accumulation mode particles were lowered (up to 15 times) for FI operation. However, the smaller nucleation mode nanoparticles increased up to 15 times. Accumulation mode particles stopped decreasing above an AFR threshold while nucleation particles continuously increased. In-cylinder combustion analysis showed a slightly smaller ignition delay and higher burn rate for FI cases relative to NA operation. Much higher peak cylinder pressures were accompanied by much lower combustion and exhaust gas temperatures (EGT), due to higher in-cylinder mass during FI operation. Peak nucleation mode emissions were shown to be negatively correlated to EGT for all the data, collapsing on a single curve. This is consistent with some other studies reporting increased nucleation mode emissions (and higher accumulation mode particles) with decreased load, lower speed, lower EGR, advanced combustion phasing, and higher injection pressure, all of which reduce EGT. The nucleation-accumulation trade-off has been explained by the ‘adsorption hypothesis’ by some investigators. In the current work, an alternative/supplemental argument has been made for the possibility that lower cylinder temperatures during the late-burning phase (correlated to lower EGT) phase hampers oxidation of nucleation mode particles and increases nucleation mode emissions.
- 19 July 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 29 (59) , 89449-89468
Nucleation-accumulation mode trade-off in non-volatile particle emissions from a small non-road small diesel engine
Small (< 8 kW) non-road engines are a significant source of pollutants such as particle number (PN) emissions. Many small non-road engines do not have diesel particulate filters (DPFs). They are so designed that air–fuel ratio (AFR) can be adjusted to control visible diesel smoke and particulate matter (PM) resulting from larger accumulation mode particles. However, the effect of AFR variation on smaller nucleation mode nanoparticle emissions is not well understood. Several studies on larger engines have reported a trade-off between smaller and larger particles. In this study, AFR was independently varied over the entire engine map of a naturally aspirated (NA) non-road small diesel engine using forced induction (FI) of externally compressed air. AFR’s ranged from 57 to 239 compared to the design range of 23–92 for the engine, including unusually high AFR’s at full-load operation, not previously reported for conventional combustion. As expected, larger accumulation mode particles were lowered (up to 15 times) for FI operation. However, the smaller nucleation mode nanoparticles increased up to 15 times. Accumulation mode particles stopped decreasing above an AFR threshold while nucleation particles continuously increased. In-cylinder combustion analysis showed a slightly smaller ignition delay and higher burn rate for FI cases relative to NA operation. Much higher peak cylinder pressures were accompanied by much lower combustion and exhaust gas temperatures (EGT), due to higher in-cylinder mass during FI operation. Peak nucleation mode emissions were shown to be negatively correlated to EGT for all the data, collapsing on a single curve. This is consistent with some other studies reporting increased nucleation mode emissions (and higher accumulation mode particles) with decreased load, lower speed, lower EGR, advanced combustion phasing, and higher injection pressure, all of which reduce EGT. The nucleation-accumulation trade-off has been explained by the ‘adsorption hypothesis’ by some investigators. In the current work, an alternative/supplemental argument has been made for the possibility that lower cylinder temperatures during the late-burning phase (correlated to lower EGT) phase hampers oxidation of nucleation mode particles and increases nucleation mode emissions.
- 1 December 2021
- Published by Elsevier in Flow Measurement and Instrumentation
- Vol. 82
Data-based estimation and simulation of compressible pulsating flow with reverse-flow through an orifice
- 1 December 2021
- Published by Elsevier in Flow Measurement and Instrumentation
- Vol. 82
Data-based estimation and simulation of compressible pulsating flow with reverse-flow through an orifice
- Open Access
- 13 May 2019
- Published by Frontiers Media SA in Frontiers in Mechanical Engineering
- Vol. 5
Measurement and Prediction of Discharge Coefficients in Highly Compressible Pulsating Flows to Improve EGR Flow Estimation and Modeling of Engine Flows
An assumption of constant discharge coefficient (Cd) is often made when modeling highly compressible pulsating engine flows through valves or other restrictions. Similarly, orifices and flow-nozzles used for real-time EGR flow estimation are often calibrated at a few steady-state points with one single constant Cd that minimizes the error over the selected points. This quasi-steady assumption is based on asymptotically constant Cd observed at high Reynolds number for steady (non-pulsating) flow. It has been shown in this work that this assumption is not accurate for pulsating flow, particularly at large amplitudes and low flow rates. The discharge coefficient of a square-edged orifice placed in the exhaust stream of a diesel engine produced Cd's varying between 0.60 and 0.90 for critical/near-critical flows. A novel pulsating flow measurement apparatus that allowed independent variation of pressure, flow rate and frequency and allowed reproducible measurements independent of transducer characteristics, produced Cd's in the range of 0.25–0.60 with a similar square-edge orifice. The variation in Cdwas found to be correlated to two dimensionless variables, η and ξ, defined as the standard deviation of the pulsating pressure signal, σΔp, normalized by and across the orifice, respectively. The results suggest that many aspects of compressible pulsating flow through flow restrictions are yet to be understood.- 13 May 2019
- Published by Frontiers Media SA in Frontiers in Mechanical Engineering
- Vol. 5
Open AccessMeasurement and Prediction of Discharge Coefficients in Highly Compressible Pulsating Flows to Improve EGR Flow Estimation and Modeling of Engine Flows
An assumption of constant discharge coefficient (Cd) is often made when modeling highly compressible pulsating engine flows through valves or other restrictions. Similarly, orifices and flow-nozzles used for real-time EGR flow estimation are often calibrated at a few steady-state points with one single constant Cd that minimizes the error over the selected points. This quasi-steady assumption is based on asymptotically constant Cd observed at high Reynolds number for steady (non-pulsating) flow. It has been shown in this work that this assumption is not accurate for pulsating flow, particularly at large amplitudes and low flow rates. The discharge coefficient of a square-edged orifice placed in the exhaust stream of a diesel engine produced Cd's varying between 0.60 and 0.90 for critical/near-critical flows. A novel pulsating flow measurement apparatus that allowed independent variation of pressure, flow rate and frequency and allowed reproducible measurements independent of transducer characteristics, produced Cd's in the range of 0.25–0.60 with a similar square-edge orifice. The variation in Cdwas found to be correlated to two dimensionless variables, η and ξ, defined as the standard deviation of the pulsating pressure signal, σΔp, normalized by and across the orifice, respectively. The results suggest that many aspects of compressible pulsating flow through flow restrictions are yet to be understood. - 28 February 2014
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 15 (7) , 877-894
Advantages and applications of transforming empirical model input space with dimensional models
Model-based calibration of steady-state engine operation is commonly performed with highly parameterized empirical models that are accurate but not very robust, particularly when predicting highly nonlinear responses such as diesel smoke emissions. To address this problem, and to boost the accuracy of more robust non-parametric methods to the same level, GT-Power was used to transform the empirical model input space into multiple input spaces that simplified the input-output relationship and improved the accuracy and robustness of smoke predictions made by three commonly used empirical modeling methods: Multivariate Regression, Neural Networks and the k-Nearest Neighbor method. The availability of multiple input spaces allowed the development of two committee techniques: a ‘Simple Committee’ technique that used averaged predictions from a set of 10 pre-selected input spaces chosen by the training data and the “Minimum Variance Committee” technique where the input spaces for each prediction were chosen on the basis of disagreement between the three modeling methods. This latter technique equalized the performance of the three modeling methods. The successively increasing improvements resulting from the use of a single best transformed input space (Best Combination Technique), Simple Committee Technique and Minimum Variance Committee Technique were verified with hypothesis testing. The transformed input spaces were also shown to improve outlier detection and to improve k-Nearest Neighbor performance when predicting dynamic emissions with steady-state training data. An unexpected finding was that the benefits of input space transformation were unaffected by changes in the hardware or the calibration of the underlying GT-Power model.
- 28 February 2014
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 15 (7) , 877-894
Advantages and applications of transforming empirical model input space with dimensional models
Model-based calibration of steady-state engine operation is commonly performed with highly parameterized empirical models that are accurate but not very robust, particularly when predicting highly nonlinear responses such as diesel smoke emissions. To address this problem, and to boost the accuracy of more robust non-parametric methods to the same level, GT-Power was used to transform the empirical model input space into multiple input spaces that simplified the input-output relationship and improved the accuracy and robustness of smoke predictions made by three commonly used empirical modeling methods: Multivariate Regression, Neural Networks and the k-Nearest Neighbor method. The availability of multiple input spaces allowed the development of two committee techniques: a ‘Simple Committee’ technique that used averaged predictions from a set of 10 pre-selected input spaces chosen by the training data and the “Minimum Variance Committee” technique where the input spaces for each prediction were chosen on the basis of disagreement between the three modeling methods. This latter technique equalized the performance of the three modeling methods. The successively increasing improvements resulting from the use of a single best transformed input space (Best Combination Technique), Simple Committee Technique and Minimum Variance Committee Technique were verified with hypothesis testing. The transformed input spaces were also shown to improve outlier detection and to improve k-Nearest Neighbor performance when predicting dynamic emissions with steady-state training data. An unexpected finding was that the benefits of input space transformation were unaffected by changes in the hardware or the calibration of the underlying GT-Power model.
- 21 November 2012
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 227 (8) , 1112-1129
A decision-tree-based approach to smoke spike detection in a heavy-duty diesel engine
Smoke spikes occurring during transient engine operation have detrimental health effects and increase fuel consumption by requiring more frequent regeneration of the diesel particulate filter. This paper proposes a decision tree approach to real-time detection of smoke spikes for control and on-board diagnostics purposes. A contemporary, electronically controlled heavy-duty diesel engine was used to investigate the deficiencies of smoke control based on the fuel-to-oxygen-ratio limit. With the aid of transient and steady state data analysis and empirical as well as dimensional modeling, it was shown that the fuel-to-oxygen ratio was not estimated correctly during the turbocharger lag period. This inaccuracy was attributed to the large manifold pressure ratios and low exhaust gas recirculation flows recorded during the turbocharger lag period, which meant that engine control module correlations for the exhaust gas recirculation flow and the volumetric efficiency had to be extrapolated. The engine control module correlations were based on steady state data and it was shown that, unless the turbocharger efficiency is artificially reduced, the large manifold pressure ratios observed during the turbocharger lag period cannot be achieved at steady state. Additionally, the cylinder-to-cylinder variation during this period were shown to be sufficiently significant to make the average fuel-to-oxygen ratio a poor predictor of the transient smoke emissions. The steady state data also showed higher smoke emissions with higher exhaust gas recirculation fractions at constant fuel-to-oxygen-ratio levels. This suggests that, even if the fuel-to-oxygen ratios were to be estimated accurately for each cylinder, they would still be ineffective as smoke limiters. A decision tree trained on snap throttle data and pruned with engineering knowledge was able to use the inaccurate engine control module estimates of the fuel-to-oxygen ratio together with information on the engine control module estimate of the exhaust gas recirculation fraction, the engine speed, and the manifold pressure ratio to predict 94% of all spikes occurring over the Federal Test Procedure cycle. The advantages of this non-parametric approach over other commonly used parametric empirical methods such as regression were described. An application of accurate smoke spike detection in which the injection pressure is increased at points with a high opacity to reduce the cumulative particulate matter emissions substantially with a minimum increase in the cumulative nitrogrn oxide emissions was illustrated with dimensional and empirical modeling.
- 21 November 2012
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 227 (8) , 1112-1129
A decision-tree-based approach to smoke spike detection in a heavy-duty diesel engine
Smoke spikes occurring during transient engine operation have detrimental health effects and increase fuel consumption by requiring more frequent regeneration of the diesel particulate filter. This paper proposes a decision tree approach to real-time detection of smoke spikes for control and on-board diagnostics purposes. A contemporary, electronically controlled heavy-duty diesel engine was used to investigate the deficiencies of smoke control based on the fuel-to-oxygen-ratio limit. With the aid of transient and steady state data analysis and empirical as well as dimensional modeling, it was shown that the fuel-to-oxygen ratio was not estimated correctly during the turbocharger lag period. This inaccuracy was attributed to the large manifold pressure ratios and low exhaust gas recirculation flows recorded during the turbocharger lag period, which meant that engine control module correlations for the exhaust gas recirculation flow and the volumetric efficiency had to be extrapolated. The engine control module correlations were based on steady state data and it was shown that, unless the turbocharger efficiency is artificially reduced, the large manifold pressure ratios observed during the turbocharger lag period cannot be achieved at steady state. Additionally, the cylinder-to-cylinder variation during this period were shown to be sufficiently significant to make the average fuel-to-oxygen ratio a poor predictor of the transient smoke emissions. The steady state data also showed higher smoke emissions with higher exhaust gas recirculation fractions at constant fuel-to-oxygen-ratio levels. This suggests that, even if the fuel-to-oxygen ratios were to be estimated accurately for each cylinder, they would still be ineffective as smoke limiters. A decision tree trained on snap throttle data and pruned with engineering knowledge was able to use the inaccurate engine control module estimates of the fuel-to-oxygen ratio together with information on the engine control module estimate of the exhaust gas recirculation fraction, the engine speed, and the manifold pressure ratio to predict 94% of all spikes occurring over the Federal Test Procedure cycle. The advantages of this non-parametric approach over other commonly used parametric empirical methods such as regression were described. An application of accurate smoke spike detection in which the injection pressure is increased at points with a high opacity to reduce the cumulative particulate matter emissions substantially with a minimum increase in the cumulative nitrogrn oxide emissions was illustrated with dimensional and empirical modeling.
- 7 December 2011
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 13 (2) , 147-168
Development of a model-based transient calibration process for diesel engine electronic control module tables – Part 2: modelling and optimization
This is the second part of a study investigating a model-based transient calibration process for diesel engines. The first part addressed the data requirements and data processing required for empirical transient emission and torque models. The current work focuses on modelling and optimization. The unexpected result of this investigation is that when trained on transient data, simple regression models perform better than more powerful methods such as neural networks or localized regression. This result has been attributed to extrapolation over data that have estimated rather than measured transient air-handling parameters. The challenges of detecting and preventing extrapolation using statistical methods that work well with steady-state data have been explained. The concept of constraining the distribution of statistical leverage relative to the distribution of the starting solution to prevent extrapolation during the optimization process has been proposed and demonstrated. Separate from the issue of extrapolation is preventing the search from being quasi-static. Second-order linear dynamic constraint models have been proposed to prevent the search from returning solutions that are feasible if each point were run at steady state, but which are unrealistic in a transient sense. Dynamic constraint models translate commanded parameters to actually achieved parameters that then feed into the transient emission and torque models. Combined model inaccuracies have been used to adjust the optimized solutions. To frame the optimization problem within reasonable dimensionality, the coefficients of commanded surfaces that approximate engine tables are adjusted during search iterations, each of which involves simulating the entire transient cycle. The resulting strategy, different from the corresponding manual calibration strategy and resulting in lower emissions and efficiency, is intended to improve rather than replace the manual calibration process.
- 7 December 2011
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 13 (2) , 147-168
Development of a model-based transient calibration process for diesel engine electronic control module tables – Part 2: modelling and optimization
This is the second part of a study investigating a model-based transient calibration process for diesel engines. The first part addressed the data requirements and data processing required for empirical transient emission and torque models. The current work focuses on modelling and optimization. The unexpected result of this investigation is that when trained on transient data, simple regression models perform better than more powerful methods such as neural networks or localized regression. This result has been attributed to extrapolation over data that have estimated rather than measured transient air-handling parameters. The challenges of detecting and preventing extrapolation using statistical methods that work well with steady-state data have been explained. The concept of constraining the distribution of statistical leverage relative to the distribution of the starting solution to prevent extrapolation during the optimization process has been proposed and demonstrated. Separate from the issue of extrapolation is preventing the search from being quasi-static. Second-order linear dynamic constraint models have been proposed to prevent the search from returning solutions that are feasible if each point were run at steady state, but which are unrealistic in a transient sense. Dynamic constraint models translate commanded parameters to actually achieved parameters that then feed into the transient emission and torque models. Combined model inaccuracies have been used to adjust the optimized solutions. To frame the optimization problem within reasonable dimensionality, the coefficients of commanded surfaces that approximate engine tables are adjusted during search iterations, each of which involves simulating the entire transient cycle. The resulting strategy, different from the corresponding manual calibration strategy and resulting in lower emissions and efficiency, is intended to improve rather than replace the manual calibration process.
- 7 November 2011
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 13 (1) , 77-96
Development of a model-based transient calibration process for diesel engine electronic control module tables – Part 1: data requirements, processing, and analysis
This is the first part of a study investigating a model-based transient calibration process for diesel engines. The motivation is to populate hundreds of parameters (which can be calibrated) in a methodical and optimum manner by using model-based optimization in conjunction with the manual process so that, relative to the manual process used by itself, a significant improvement in transient emissions and fuel consumption and a sizable reduction in calibration time and test cell requirements is achieved. Empirical transient modelling and optimization has been addressed in the second part of this work, while the required data for model training and generalization are the focus of the current work. Transient and steady-state data from a turbocharged multicylinder diesel engine have been examined from a model training perspective. A single-cylinder engine with external air-handling has been used to expand the steady-state data to encompass transient parameter space. Based on comparative model performance and differences in the non-parametric space, primarily driven by a high engine difference between exhaust and intake manifold pressures (ΔP) during transients, it has been recommended that transient emission models should be trained with transient training data. It has been shown that electronic control module (ECM) estimates of transient charge flow and the exhaust gas recirculation (EGR) fraction cannot be accurate at the high engine ΔP frequently encountered during transient operation, and that such estimates do not account for cylinder-to-cylinder variation. The effects of high engine ΔP must therefore be incorporated empirically by using transient data generated from a spectrum of transient calibrations. Specific recommendations on how to choose such calibrations, how many data to acquire, and how to specify transient segments for data acquisition have been made. Methods to process transient data to account for transport delays and sensor lags have been developed. The processed data have then been visualized using statistical means to understand transient emission formation. Two modes of transient opacity formation have been observed and described. The first mode is driven by high engine ΔP and low fresh air flowrates, while the second mode is driven by high engine ΔP and high EGR flowrates. The EGR fraction is inaccurately estimated at both modes, while EGR distribution has been shown to be present but unaccounted for by the ECM. The two modes and associated phenomena are essential to understanding why transient emission models are calibration dependent and furthermore how to choose training data that will result in good model generalization.
- 7 November 2011
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 13 (1) , 77-96
Development of a model-based transient calibration process for diesel engine electronic control module tables – Part 1: data requirements, processing, and analysis
This is the first part of a study investigating a model-based transient calibration process for diesel engines. The motivation is to populate hundreds of parameters (which can be calibrated) in a methodical and optimum manner by using model-based optimization in conjunction with the manual process so that, relative to the manual process used by itself, a significant improvement in transient emissions and fuel consumption and a sizable reduction in calibration time and test cell requirements is achieved. Empirical transient modelling and optimization has been addressed in the second part of this work, while the required data for model training and generalization are the focus of the current work. Transient and steady-state data from a turbocharged multicylinder diesel engine have been examined from a model training perspective. A single-cylinder engine with external air-handling has been used to expand the steady-state data to encompass transient parameter space. Based on comparative model performance and differences in the non-parametric space, primarily driven by a high engine difference between exhaust and intake manifold pressures (ΔP) during transients, it has been recommended that transient emission models should be trained with transient training data. It has been shown that electronic control module (ECM) estimates of transient charge flow and the exhaust gas recirculation (EGR) fraction cannot be accurate at the high engine ΔP frequently encountered during transient operation, and that such estimates do not account for cylinder-to-cylinder variation. The effects of high engine ΔP must therefore be incorporated empirically by using transient data generated from a spectrum of transient calibrations. Specific recommendations on how to choose such calibrations, how many data to acquire, and how to specify transient segments for data acquisition have been made. Methods to process transient data to account for transport delays and sensor lags have been developed. The processed data have then been visualized using statistical means to understand transient emission formation. Two modes of transient opacity formation have been observed and described. The first mode is driven by high engine ΔP and low fresh air flowrates, while the second mode is driven by high engine ΔP and high EGR flowrates. The EGR fraction is inaccurately estimated at both modes, while EGR distribution has been shown to be present but unaccounted for by the ECM. The two modes and associated phenomena are essential to understanding why transient emission models are calibration dependent and furthermore how to choose training data that will result in good model generalization.