Development of a model-based transient calibration process for diesel engine electronic control module tables – Part 1: data requirements, processing, and analysis
Authors:
- 7 November 2011
- journal article
- research article
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 13 (1) , 77-96
Abstract
This is the first part of a study investigating a model-based transient calibration process for diesel engines. The motivation is to populate hundreds of parameters (which can be calibrated) in a methodical and optimum manner by using model-based optimization in conjunction with the manual process so that, relative to the manual process used by itself, a significant improvement in transient emissions and fuel consumption and a sizable reduction in calibration time and test cell requirements is achieved. Empirical transient modelling and optimization has been addressed in the second part of this work, while the required data for model training and generalization are the focus of the current work. Transient and steady-state data from a turbocharged multicylinder diesel engine have been examined from a model training perspective. A single-cylinder engine with external air-handling has been used to expand the steady-state data to encompass transient parameter space. Based on comparative model performance and differences in the non-parametric space, primarily driven by a high engine difference between exhaust and intake manifold pressures (ΔP) during transients, it has been recommended that transient emission models should be trained with transient training data. It has been shown that electronic control module (ECM) estimates of transient charge flow and the exhaust gas recirculation (EGR) fraction cannot be accurate at the high engine ΔP frequently encountered during transient operation, and that such estimates do not account for cylinder-to-cylinder variation. The effects of high engine ΔP must therefore be incorporated empirically by using transient data generated from a spectrum of transient calibrations. Specific recommendations on how to choose such calibrations, how many data to acquire, and how to specify transient segments for data acquisition have been made. Methods to process transient data to account for transport delays and sensor lags have been developed. The processed data have then been visualized using statistical means to understand transient emission formation. Two modes of transient opacity formation have been observed and described. The first mode is driven by high engine ΔP and low fresh air flowrates, while the second mode is driven by high engine ΔP and high EGR flowrates. The EGR fraction is inaccurately estimated at both modes, while EGR distribution has been shown to be present but unaccounted for by the ECM. The two modes and associated phenomena are essential to understanding why transient emission models are calibration dependent and furthermore how to choose training data that will result in good model generalization.Keywords
This publication has 25 references indexed in Scilit:
- Model-Based Actuator Trajectories Optimization for a Diesel Engine Using a Direct MethodJournal of Engineering for Gas Turbines and Power, 2010
- Transient EGR in a High-Speed DI Diesel Engine for a set of different EGR-routingsSAE International Journal of Engines, 2010
- Empirical Modeling of Transient Emissions and Transient Response for Transient OptimizationSAE International Journal of Engines, 2009
- The Influence of Accelerator Pedal Position Control during Transient Laboratory Testing on Heavy Duty Diesel EnginesSAE International Journal of Engines, 2009
- Development of the nearest neighbour multivariate localized regression modelling technique for steady state engine calibration and comparison with neural networks and global regressionInternational Journal of Engine Research, 2008
- Measurement and Simulation of Instantaneous Emissions of a Heavy Truck Diesel Engine During TransientsJournal of Engineering for Gas Turbines and Power, 2008
- Investigating the impact of in-vehicle transients on diesel soot emissionsThermal Science, 2008
- Influence of Engine Operating Conditions on Diesel Particulate Matter Emissions in Relation to Transient and Steady-State ConditionsEnvironmental Science & Technology, 2007
- Optimization of Heavy-Duty Diesel Engine Operating Parameters Using A Response Surface MethodSAE International Journal of Advances and Current Practices in Mobility, 2000
- Statistical Methods for Solving the Fuel Consumption/Emission Conflict on DI-Diesel EnginesSAE International Journal of Advances and Current Practices in Mobility, 1999