Bernhard A. Schrefler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bernhard A. Schrefler has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Dariusz Gawin
Department of Building Materials Physics and Sustainable Design, Lodz University of Technology, Av. Politechniki 6, 90-924 Lodz, Poland
9 shared publications - Francesco Pesavento
University of Padova
8 shared publications - Peter Wriggers
Institute of Continuum Mechanics, Leibniz University Hannover, Hannover, Germany
3 shared publications C. E. Majorana
Dipartimento di Costruzioni e Trasporti, Università di Padova, via F.Marzolo 9, 35131 Padova, Italy
2 shared publications- Giorgio Zavarise
University of Salento
2 shared publications - Luciano Simoni
Università diPadova
2 shared publications
Latest Publications
- 1 September 2015
- Published by Elsevier in Gait & Posture
- Vol. 42, S24-S25
A foot finite element model integrating porous media approach and gait analysis: A step forward in the study of the diabetic foot disease
- 1 September 2015
- Published by Elsevier in Gait & Posture
- Vol. 42, S24-S25
A foot finite element model integrating porous media approach and gait analysis: A step forward in the study of the diabetic foot disease
- Open Access
- 17 September 2013
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 6, 05005
Fully coupled numerical simulation of fire in tunnels: From fire scenario to structural response
- 17 September 2013
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 6, 05005
Open AccessFully coupled numerical simulation of fire in tunnels: From fire scenario to structural response
- 1 September 2010
- Published by Springer Nature
- p. 381-404
Multiscale/Multiphysics Model for Concrete
- 17 September 2009
- Published by Civil-Comp, Ltd.
On Numerical Analysis of Thermomechanical Contact Problems
- 17 September 2009
- Published by Civil-Comp, Ltd.
On Numerical Analysis of Thermomechanical Contact Problems
- 25 May 2009
- Published by Civil-Comp, Ltd.
- p. 63-91
Concrete Structures Subject to High Temperature
- 27 June 2008
- Published by Springer Nature in Computational Mechanics
- Vol. 43 (1) , 179-189
Numerical difficulties and computational procedures for thermo-hydro-mechanical coupled problems of saturated porous media
- 27 June 2008
- Published by Springer Nature in Computational Mechanics
- Vol. 43 (1) , 179-189
Numerical difficulties and computational procedures for thermo-hydro-mechanical coupled problems of saturated porous media
- 23 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 17 (2) , 1362-1365
Thermo-Mechanics of the Hierarchical Structure of ITER Superconducting Cables
Recent experimental tests on the model coils have shown that the behavior of Nb3Sn based cables is not as good as expected on the basis of the characteristics evaluated for the uncabled strands. This degradation of the cable performance seems to be due to various factors, among which the strain state of the filaments due to bending and contact phenomena inside the cable. After these results it was decided that high performance strands will be used for ITER magnets, even if they have never been tested on a full size cable. Therefore the capability of evaluating the coil performance from the strands characteristics becomes a crucial point in the Research and Development (R&D) activity. Recently some extrapolations were attempted, but the mechanical model used is rather simplified and needs some fitting parameters which are not known a priori. In this work we present a thermo-mechanical model suitably developed to evaluate the strain state of a Nb3Sn strand inside a superconducting (SC) cable. It is based on the idea of multiscale modeling, starting from a enriched formulation of the beam kinematics to take into account the fibrous nature of a multifilamentary strand. The method consists in performing a successive substitution of discrete models involving many beams with a single equivalent beam model, which behavior is identified from the preceding cabling stage. This recursive substitution allows to perform the analysis within a reasonable computational time. Once the stress and strain fields are obtained at the higher level, a suitable unsmearing technique gives the strain till the first level, on the scale of the SC filament. The method is applied to the real case of the 3 times 3 and 3 times 3 times 5 CICC sub-size samples tested at FZK in Germany.
- 23 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 17 (2) , 1362-1365
Thermo-Mechanics of the Hierarchical Structure of ITER Superconducting Cables
Recent experimental tests on the model coils have shown that the behavior of Nb3Sn based cables is not as good as expected on the basis of the characteristics evaluated for the uncabled strands. This degradation of the cable performance seems to be due to various factors, among which the strain state of the filaments due to bending and contact phenomena inside the cable. After these results it was decided that high performance strands will be used for ITER magnets, even if they have never been tested on a full size cable. Therefore the capability of evaluating the coil performance from the strands characteristics becomes a crucial point in the Research and Development (R&D) activity. Recently some extrapolations were attempted, but the mechanical model used is rather simplified and needs some fitting parameters which are not known a priori. In this work we present a thermo-mechanical model suitably developed to evaluate the strain state of a Nb3Sn strand inside a superconducting (SC) cable. It is based on the idea of multiscale modeling, starting from a enriched formulation of the beam kinematics to take into account the fibrous nature of a multifilamentary strand. The method consists in performing a successive substitution of discrete models involving many beams with a single equivalent beam model, which behavior is identified from the preceding cabling stage. This recursive substitution allows to perform the analysis within a reasonable computational time. Once the stress and strain fields are obtained at the higher level, a suitable unsmearing technique gives the strain till the first level, on the scale of the SC filament. The method is applied to the real case of the 3 times 3 and 3 times 3 times 5 CICC sub-size samples tested at FZK in Germany.
- 31 January 2006
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 67 (3) , 299-331
Hygro-thermo-chemo-mechanical modelling of concrete at early ages and beyond. Part I: hydration and hygro-thermal phenomena
- 31 January 2006
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 67 (3) , 299-331
Hygro-thermo-chemo-mechanical modelling of concrete at early ages and beyond. Part I: hydration and hygro-thermal phenomena
- 31 January 2006
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 67 (3) , 332-363
Hygro-thermo-chemo-mechanical modelling of concrete at early ages and beyond. Part II: shrinkage and creep of concrete
- 31 January 2006
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 67 (3) , 332-363
Hygro-thermo-chemo-mechanical modelling of concrete at early ages and beyond. Part II: shrinkage and creep of concrete
- 27 January 2006
- Published by Springer Nature
- Vol. 125, 91-97
A Multiphase Approach for the Analysis of Hygro-Thermo-Chemo-Mechanical Interactions in Concrete at Early Ages and at High Temperature
- 27 January 2006
- Published by Springer Nature
- Vol. 125, 91-97
A Multiphase Approach for the Analysis of Hygro-Thermo-Chemo-Mechanical Interactions in Concrete at Early Ages and at High Temperature