Akimaro Kawahara
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Akimaro Kawahara has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Michio Sadatomi
Graduate School of Science and Technology, Kumamoto University
23 shared publications - Yukihiro Yonemoto
Faculty of Advanced Science and Technology, Kumamoto University , 2-39-1 Kurokami, Chuo-Ku, Kumamoto 860-8555
7 shared publications Michio Sadatomi
Graduate School of Science and Technology, Kumamoto University
6 shared publicationsYukihiro Yonemoto
Kumamoto University, Faculty of Advanced Science and Technology, Kumamoto, Japan
5 shared publicationsTomoaki Takehira
4 shared publicationsYoshifusa Sato
4 shared publications
Latest Publications
- 1 April 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (4)
Pressure changes through a sudden expansion in rectangular microchannels for laminar and turbulent flows
This study experimentally investigates the relationship between the pressure change (ΔPe) at a sudden expansion and the Reynolds number for liquid flows in rectangular microchannels with different expansion ratios. In the experiments, water and an aqueous glycerol solution with various mass concentrations were used as test liquids, and detailed pressure distributions near the sudden expansion section were measured to determine the ΔPe under laminar to turbulent flow conditions. The experimental results showed that ΔPe increases with Reynolds number; however, the increasing trend is affected by the flow conditions both upstream and downstream of the expansion as well as by the reattachment length of the recirculation region formed downstream of the expansion. The Borda–Carnot equation was found to underestimate ΔPe, particularly in the laminar flow regime. To address this, a prediction model for ΔPe was developed by considering both the velocity distribution and the reattachment length effects. The model parameters were determined by applying the least-squares method, with supporting findings from previous studies for the momentum correction factor, Darcy friction factor, and the reattachment length. The proposed model successfully predicted ΔPe within ±12% on average over a wide Reynolds number range from laminar to turbulent flow regimes. These results demonstrate that the model provides a reliable basis for evaluating expansion losses in microchannels and has potential applicability to the design of microfluidic and microreactor systems.
- 1 April 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (4)
Pressure changes through a sudden expansion in rectangular microchannels for laminar and turbulent flows
This study experimentally investigates the relationship between the pressure change (ΔPe) at a sudden expansion and the Reynolds number for liquid flows in rectangular microchannels with different expansion ratios. In the experiments, water and an aqueous glycerol solution with various mass concentrations were used as test liquids, and detailed pressure distributions near the sudden expansion section were measured to determine the ΔPe under laminar to turbulent flow conditions. The experimental results showed that ΔPe increases with Reynolds number; however, the increasing trend is affected by the flow conditions both upstream and downstream of the expansion as well as by the reattachment length of the recirculation region formed downstream of the expansion. The Borda–Carnot equation was found to underestimate ΔPe, particularly in the laminar flow regime. To address this, a prediction model for ΔPe was developed by considering both the velocity distribution and the reattachment length effects. The model parameters were determined by applying the least-squares method, with supporting findings from previous studies for the momentum correction factor, Darcy friction factor, and the reattachment length. The proposed model successfully predicted ΔPe within ±12% on average over a wide Reynolds number range from laminar to turbulent flow regimes. These results demonstrate that the model provides a reliable basis for evaluating expansion losses in microchannels and has potential applicability to the design of microfluidic and microreactor systems.
- Open Access
- 30 April 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (5) , 545
Rheological Property Changes in Polyacrylamide Aqueous Solution Flowed Through Microchannel Under Low Reynolds Number and High Shear Rate Conditions
As an important structure of microfluidic devices, microchannels have the advantages of precise flow control and high reaction efficiency. This study investigates experimentally changing the rheological properties of a polyacrylamide (PAM) aqueous solution after flowing through a square microchannel with a hydraulic diameter of 0.5 mm under low Reynolds number and high shear rate conditions. To know the effect of the channel length on the change in viscosity and relaxation time, the length is changed to 100 mm and 200 mm. From the experiment, it is found that both the viscosity and relaxation time of the solution decrease with increasing the shear rate and the microchannel length. Based on the present experimental data, an empirical model is proposed to predict the change ratio of the relaxation time before and after passing through the microchannel, and the calculation with the model has an agreement with the experiment with root-mean-square absolute error of 0.007.
- 30 April 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (5) , 545
Open AccessRheological Property Changes in Polyacrylamide Aqueous Solution Flowed Through Microchannel Under Low Reynolds Number and High Shear Rate Conditions
As an important structure of microfluidic devices, microchannels have the advantages of precise flow control and high reaction efficiency. This study investigates experimentally changing the rheological properties of a polyacrylamide (PAM) aqueous solution after flowing through a square microchannel with a hydraulic diameter of 0.5 mm under low Reynolds number and high shear rate conditions. To know the effect of the channel length on the change in viscosity and relaxation time, the length is changed to 100 mm and 200 mm. From the experiment, it is found that both the viscosity and relaxation time of the solution decrease with increasing the shear rate and the microchannel length. Based on the present experimental data, an empirical model is proposed to predict the change ratio of the relaxation time before and after passing through the microchannel, and the calculation with the model has an agreement with the experiment with root-mean-square absolute error of 0.007.
- 20 March 2024
- Published by Springer Nature
- p. 41-49
Effects of Salinity on Carbon Dioxide Microbubble Dissolution into Water
- 20 March 2024
- Published by Springer Nature
- p. 41-49
Effects of Salinity on Carbon Dioxide Microbubble Dissolution into Water
- 11 May 2023
- Published by Taylor & Francis in Nuclear Technology
- Vol. 209 (12) , 1-15
Liquid Film Thickness for Gas-Liquid Annular Flow Across Grid Spacer with Vanes in Simple 3 × 3 Rod Bundle Channel
This study reports the effects of the grid spacer with mixing vane (MV) on gas velocity for air single-phase flow and liquid film thickness for air-water two-phase annular flow in a 3 × 3 rod bundle channel. To investigate the effects of the shape of the spacers, three kinds of spacers were installed into the channel: spacer without MV (without MV), spacer with four MVs (4-MV30), and spacer with two MVs (2-MV30). The 4-MV30 and 2-MV30 had vanes that were inclined 30 deg from the vertical axis. Gas velocity was measured with a hot-wire anemometer and liquid film thickness was measured with the constant electric current method. From the gas velocity measurement, it was found that the irregularities in the velocity distribution became smaller toward downstream of the spacer. For the 2-MV30, the flow distribution was asymmetric and the flow was biased. From the liquid film thickness measurement, it was found that the liquid film thickness became thicker downstream of the spacer.
- 11 May 2023
- Published by Taylor & Francis in Nuclear Technology
- Vol. 209 (12) , 1-15
Liquid Film Thickness for Gas-Liquid Annular Flow Across Grid Spacer with Vanes in Simple 3 × 3 Rod Bundle Channel
This study reports the effects of the grid spacer with mixing vane (MV) on gas velocity for air single-phase flow and liquid film thickness for air-water two-phase annular flow in a 3 × 3 rod bundle channel. To investigate the effects of the shape of the spacers, three kinds of spacers were installed into the channel: spacer without MV (without MV), spacer with four MVs (4-MV30), and spacer with two MVs (2-MV30). The 4-MV30 and 2-MV30 had vanes that were inclined 30 deg from the vertical axis. Gas velocity was measured with a hot-wire anemometer and liquid film thickness was measured with the constant electric current method. From the gas velocity measurement, it was found that the irregularities in the velocity distribution became smaller toward downstream of the spacer. For the 2-MV30, the flow distribution was asymmetric and the flow was biased. From the liquid film thickness measurement, it was found that the liquid film thickness became thicker downstream of the spacer.
- Open Access
Pressure Change for Single- and Two-Phase Non-Newtonian Flows through Sudden Contraction in Rectangular Microchannel
The flow characteristics of the single-phase liquid and the gas–liquid two-phase flows including the Newtonian and non-Newtonian liquids were experimentally investigated in a horizontal rectangular micro-channel with a sudden contraction—specifically the pressure change across the contraction. The rectangular cross-sectional dimension has Wu × Hu (width × height) = 0.99 × 0.50 mm2 on the upstream side of the contraction and Wd × Hd = 0.49 × 0.50 mm2 on the downstream side. The resulting contraction ratio, σA (=Wd/Wu), was 0.5. Air was used as the test gas (in the case of the gas–liquid two-phase flow experiment), distilled water and three kinds of aqueous solution, i.e., glycerin 25 wt%, xanthangum 0.1 wt% and polyacrylamide 0.11 wt% were used as the test liquid. The pressure distribution in the flow direction upstream and downstream of the channel was measured. The pressure change and loss at the sudden contraction were determined from the pressure distribution. In addition, the pressure change data were compared with the calculation by several correlations proposed by various researchers as well as a newly developed correlation in this study. From the comparisons, it was found that calculations by the newly developed correlations agreed well with the measured values within the error of 30%.
Open AccessPressure Change for Single- and Two-Phase Non-Newtonian Flows through Sudden Contraction in Rectangular Microchannel
The flow characteristics of the single-phase liquid and the gas–liquid two-phase flows including the Newtonian and non-Newtonian liquids were experimentally investigated in a horizontal rectangular micro-channel with a sudden contraction—specifically the pressure change across the contraction. The rectangular cross-sectional dimension has Wu × Hu (width × height) = 0.99 × 0.50 mm2 on the upstream side of the contraction and Wd × Hd = 0.49 × 0.50 mm2 on the downstream side. The resulting contraction ratio, σA (=Wd/Wu), was 0.5. Air was used as the test gas (in the case of the gas–liquid two-phase flow experiment), distilled water and three kinds of aqueous solution, i.e., glycerin 25 wt%, xanthangum 0.1 wt% and polyacrylamide 0.11 wt% were used as the test liquid. The pressure distribution in the flow direction upstream and downstream of the channel was measured. The pressure change and loss at the sudden contraction were determined from the pressure distribution. In addition, the pressure change data were compared with the calculation by several correlations proposed by various researchers as well as a newly developed correlation in this study. From the comparisons, it was found that calculations by the newly developed correlations agreed well with the measured values within the error of 30%.
- 28 March 2020
- Published by Springer Nature in Flow, Turbulence and Combustion
- Vol. 105 (4) , 1325-1344
Pressure Drop for Gas and Polymer Aqueous Solution Two-Phase Flows in Horizontal Circular Microchannel
- 28 March 2020
- Published by Springer Nature in Flow, Turbulence and Combustion
- Vol. 105 (4) , 1325-1344
Pressure Drop for Gas and Polymer Aqueous Solution Two-Phase Flows in Horizontal Circular Microchannel
- 1 January 2019
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2019, S08117
Effects of grid spacer with vanes on liquid film for gas-liquid two-phase annular flow in 3×3 rod bundle channel
This paper reports the effects of the grid spacer with mixing vane (MV) on gas velocity for air single-phase flow and liquid film thickness for air-water two-phase annular flow in a 3×3 rod bundle channel. To investigate the effects of the shape of spacers, three kinds of spacer were installed into the channel: spacer without MV (Without MV), spacer with four MV (4-MV30), and spacer with two MV (2-MV30). 4-MV30 and 2-MV30 had vanes which were inclined 30° from vertical axis. Gas velocity was measured with hot-wire anemometer and liquid film thickness was measured with constant electric current method. From the gas velocity measurement, it was found that the irregularities in the velocity distribution became smaller toward the downstream of the spacer. For 2-MV30, the flow distribution was asymmetric and the flow was biased. From the liquid film thickness measurement, it was found that the liquid film thickness became thicker downstream of the spacer.
- 1 January 2019
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2019, S08117
Effects of grid spacer with vanes on liquid film for gas-liquid two-phase annular flow in 3×3 rod bundle channel
This paper reports the effects of the grid spacer with mixing vane (MV) on gas velocity for air single-phase flow and liquid film thickness for air-water two-phase annular flow in a 3×3 rod bundle channel. To investigate the effects of the shape of spacers, three kinds of spacer were installed into the channel: spacer without MV (Without MV), spacer with four MV (4-MV30), and spacer with two MV (2-MV30). 4-MV30 and 2-MV30 had vanes which were inclined 30° from vertical axis. Gas velocity was measured with hot-wire anemometer and liquid film thickness was measured with constant electric current method. From the gas velocity measurement, it was found that the irregularities in the velocity distribution became smaller toward the downstream of the spacer. For 2-MV30, the flow distribution was asymmetric and the flow was biased. From the liquid film thickness measurement, it was found that the liquid film thickness became thicker downstream of the spacer.
- 15 March 2018
- Published by The Japanese Society for Multiphase Flow in JAPANESE JOURNAL OF MULTIPHASE FLOW
- Vol. 32 (1) , 150-158
Surface Wettability Effects on Flow Characteristics in Gas-liquid Two-phase Flow through Rectangular Horizontal Micro-channel
- 15 March 2018
- Published by The Japanese Society for Multiphase Flow in JAPANESE JOURNAL OF MULTIPHASE FLOW
- Vol. 32 (1) , 150-158
Surface Wettability Effects on Flow Characteristics in Gas-liquid Two-phase Flow through Rectangular Horizontal Micro-channel
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in Transactions of the JSME (in Japanese)
- Vol. 83 (847) , 16-386
Two-phase pressure drop for gas and non-Newtonian liquid flows through circular microchannel
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in Transactions of the JSME (in Japanese)
- Vol. 83 (847) , 16-386
Two-phase pressure drop for gas and non-Newtonian liquid flows through circular microchannel
- 1 January 2016
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2016, J0270206
Effects of Channel Wall Surface Wettability on Characteristics of Gas-Liquid Two-Phase Flow through Horizontal Rectangular Mini-Channel
Experiments were conducted for air-water two-phase flow using a horizontal rectangular mini-channel having hydraulic diameter of DH = 3.2 mm. In order to know the effects of the channel wall surface wettability on the two-phase flows, the wettability on the test section was changed by coating the hydrophobic agent. The contact angles, θa, were approximately 80° for the wall surface without coating and 115° for one with coating. In the present experiments, flow pattern, bubble length and pressure drop were measured. The experimental results for coating and non-coating cases were compared each other. From the comparison, it found that surface with the coating makes bubbles length longer, and for the coating case the frictional pressure drop is smaller than the non-coating one.
- 1 January 2016
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2016, J0270206
Effects of Channel Wall Surface Wettability on Characteristics of Gas-Liquid Two-Phase Flow through Horizontal Rectangular Mini-Channel
Experiments were conducted for air-water two-phase flow using a horizontal rectangular mini-channel having hydraulic diameter of DH = 3.2 mm. In order to know the effects of the channel wall surface wettability on the two-phase flows, the wettability on the test section was changed by coating the hydrophobic agent. The contact angles, θa, were approximately 80° for the wall surface without coating and 115° for one with coating. In the present experiments, flow pattern, bubble length and pressure drop were measured. The experimental results for coating and non-coating cases were compared each other. From the comparison, it found that surface with the coating makes bubbles length longer, and for the coating case the frictional pressure drop is smaller than the non-coating one.