B. Mohan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
B. Mohan has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Gnanasambandam Anbuchezhiyan
Department of Mechanical Engineering, Vel Tech Rangarajan Dr Sagunthala R&D Institute of Science and Technology, Avadi, Chennai, India
5 shared publications - Natarajan Senthilkumar
Department of Mechanical Engineering, Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences (SIMATS), Chennai 602105, India
3 shared publications - S. Kathiresan
Department of Mechanical Engineering, Prince Shri Venkateshwara Padmavathy Engineering College, Chennai, India
2 shared publications - Saravanakumar Devaraj
School of Mechanical Engineering, Vellore Institute of Technology, Chennai, India
2 shared publications - Thangaraj Muthuramalingam
SRM Institute of Science and Technology
2 shared publications - Arunachalam Rajadurai
Anna University
1 shared publication
Latest Publications
- 29 June 2023
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 18 (2) , 997-1011
Synthesization and Characterization of Silicon Carbide and Boron Nitride-Reinforced Al–Zn–Mg Alloy Hybrid Nanocomposites Using Squeeze Casting Method
- 29 June 2023
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 18 (2) , 997-1011
Synthesization and Characterization of Silicon Carbide and Boron Nitride-Reinforced Al–Zn–Mg Alloy Hybrid Nanocomposites Using Squeeze Casting Method
- 9 January 2021
- Published by Springer Nature in Silicon
- Vol. 13 (10) , 3639-3647
Implications of SiC/Al2O3 Reinforced Al-Mg-Zn Alloy Hybrid Nano Composites Using Vacuum Sintering Method
- 9 January 2021
- Published by Springer Nature in Silicon
- Vol. 13 (10) , 3639-3647
Implications of SiC/Al2O3 Reinforced Al-Mg-Zn Alloy Hybrid Nano Composites Using Vacuum Sintering Method
- 5 January 2021
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 30 (2) , 1545-1553
Influence of Rotational Magnetorheological Abrasive Flow Finishing Process on Biocompatibility of Stainless Steel 316L
- 5 January 2021
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 30 (2) , 1545-1553
Influence of Rotational Magnetorheological Abrasive Flow Finishing Process on Biocompatibility of Stainless Steel 316L
- 3 January 2021
- Published by Springer Nature in Metals and Materials International
- Vol. 27 (8) , 3058-3069
Synthesis and Characterization of Silicon Nitride Reinforced Al–Mg–Zn Alloy Composites
- 3 January 2021
- Published by Springer Nature in Metals and Materials International
- Vol. 27 (8) , 3058-3069
Synthesis and Characterization of Silicon Nitride Reinforced Al–Mg–Zn Alloy Composites
- Open Access
- 1 November 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (11) , 115701
An investigation on microstructure and mechanical behaviour of copper-nickel coated carbon fibre reinforced aluminium composites
In the present investigation, mechanical, corrosion and fatigue characterization is performed on the fabricated aluminium metal matrix composite (AMMC), by reinforcing nickel (Ni) and copper (Cu) coated 4% carbon fibre (CF) in aluminium alloy (AA6026) matrix. With a view of enhancing the strength of the aluminium alloy, an optimal percentage (4 wt%) of CFs is reinforced; as CFs cannot be directly reinforced in the aluminium matrix due to poor wettability, CFs are coated with Ni and Cu using electroless plating technique for better wettability and bonding between reinforcement and matrix. Properties of the cast alloy and coated CF reinforced composite are compared and the composite with better properties is identified as 4% Cu coated CFs reinforced AMMC. When compared with as-cast alloy and Ni coated CF reinforced composite, the tensile strength of Cu coated CFs composite was higher by 15.36% and 2.55%. Similarly, micro-Vickers hardness was improved by 7.61% and 3.09%, impact strength by 19.61% and 3.39%, flexural strength by 87.50% and 15.38%. The corrosion rate (mils/year) was reduced with incorporation of 4% Cu coated CFs in AA6026 by 59.72% and 23.23% as compared with as-cast and Ni coated CF reinforced composition.
- 1 November 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (11) , 115701
Open AccessAn investigation on microstructure and mechanical behaviour of copper-nickel coated carbon fibre reinforced aluminium composites
In the present investigation, mechanical, corrosion and fatigue characterization is performed on the fabricated aluminium metal matrix composite (AMMC), by reinforcing nickel (Ni) and copper (Cu) coated 4% carbon fibre (CF) in aluminium alloy (AA6026) matrix. With a view of enhancing the strength of the aluminium alloy, an optimal percentage (4 wt%) of CFs is reinforced; as CFs cannot be directly reinforced in the aluminium matrix due to poor wettability, CFs are coated with Ni and Cu using electroless plating technique for better wettability and bonding between reinforcement and matrix. Properties of the cast alloy and coated CF reinforced composite are compared and the composite with better properties is identified as 4% Cu coated CFs reinforced AMMC. When compared with as-cast alloy and Ni coated CF reinforced composite, the tensile strength of Cu coated CFs composite was higher by 15.36% and 2.55%. Similarly, micro-Vickers hardness was improved by 7.61% and 3.09%, impact strength by 19.61% and 3.39%, flexural strength by 87.50% and 15.38%. The corrosion rate (mils/year) was reduced with incorporation of 4% Cu coated CFs in AA6026 by 59.72% and 23.23% as compared with as-cast and Ni coated CF reinforced composition.
- 1 June 2020
- Published by Trans Tech Publications, Ltd. in Journal of Nano Research
- Vol. 63, 98-111
Multi-Objective Optimization of Magneto Rheological Abrasive Flow Nano Finishing Process on AISI Stainless Steel 316L
In this experimental work, Magneto rheological abrasive flow nano finishing processes were conducted on AISI Stainless steel 316L work pieces that are widely used in medical implants. The focus of the present study is to assess the effect of input variables namely the volume percentage of iron (Fe) particles, silicon carbide (SiC) abrasive particles in the Magneto rheological abrasive fluid and number of cycles on the final surface roughness at nano level as well as the material removal rate. The volume % of Fe particles were taken as 20, 25 and 30 and the volume % of SiC particles were taken as 10, 15 and 20. The different number of cycles considered for the study is 100,200 and 300. There are 20 different set of experiments with different combinations of input variables mentioned have been carried out based on the experimental design derived through central composite design technique. The minimum surface roughness observed is 23.34 nanometer (nm) from the initial surface roughness of 1.92 micro meter (mu m). Towards optimizing the input process variables, a multi objective optimization was carried out by using response surface methodology.
- 1 June 2020
- Published by Trans Tech Publications, Ltd. in Journal of Nano Research
- Vol. 63, 98-111
Multi-Objective Optimization of Magneto Rheological Abrasive Flow Nano Finishing Process on AISI Stainless Steel 316L
In this experimental work, Magneto rheological abrasive flow nano finishing processes were conducted on AISI Stainless steel 316L work pieces that are widely used in medical implants. The focus of the present study is to assess the effect of input variables namely the volume percentage of iron (Fe) particles, silicon carbide (SiC) abrasive particles in the Magneto rheological abrasive fluid and number of cycles on the final surface roughness at nano level as well as the material removal rate. The volume % of Fe particles were taken as 20, 25 and 30 and the volume % of SiC particles were taken as 10, 15 and 20. The different number of cycles considered for the study is 100,200 and 300. There are 20 different set of experiments with different combinations of input variables mentioned have been carried out based on the experimental design derived through central composite design technique. The minimum surface roughness observed is 23.34 nanometer (nm) from the initial surface roughness of 1.92 micro meter (mu m). Towards optimizing the input process variables, a multi objective optimization was carried out by using response surface methodology.
- 2 September 2018
- Published by Springer Nature
- p. 39-45
Synthesis and Characterization of Nano-Glass Particles Reinforced AZ91D Magnesium Alloy Composites
- 2 September 2018
- Published by Springer Nature
- p. 39-45
Synthesis and Characterization of Nano-Glass Particles Reinforced AZ91D Magnesium Alloy Composites
- 1 May 2018
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 274, 155-164
Performance evaluation of interconnected pneumatic cylinders positioning system
- 1 May 2018
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 274, 155-164
Performance evaluation of interconnected pneumatic cylinders positioning system
- 9 March 2018
- Published by Springer Nature in Silicon
- Vol. 10 (5) , 1785-1792
Performance Analysis of Pulse Generators on Residual Stress of Machined Silicon Steel Using the EDM Process
- 9 March 2018
- Published by Springer Nature in Silicon
- Vol. 10 (5) , 1785-1792
Performance Analysis of Pulse Generators on Residual Stress of Machined Silicon Steel Using the EDM Process
- 13 March 2017
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 69 (2) , 241-247
Sliding wear behaviour of Al-Si alloy–fly ash composites produced by powder metallurgy technique
Purpose: Metal matrix composites (MMCs) are commonly used in many aerospace and industrial applications. MMCs possess significantly improved properties including high specific strength, specific modulus, damping capacity and good wear resistance compared to unreinforced alloys. The purpose of this paper is to describe the tribological studies of Al-Si alloy–fly ash composites manufactured using powder metallurgy technique. Design/methodology/approach: Al-Si (12 Wt.%) alloy–fly ash composites were developed using powder metallurgy technique. Al-Si alloy powder was used as matrix material, and the fly ash was used as reinforcement. The particle size of Al-Si alloy powder was in the range of 75-300 μm, and the fly ash was in the range of 1-15 μm. The friction and wear characteristics of the composites were studied using a pin-on-disc set up. The test specimen was mated against cast iron disc, and the tests were conducted with the loads of 10, 20 and 30 N, sliding speeds of 0.5, 1 and 1.5 m/s for a sliding distance of 2,000 m. Findings: The effects of load and sliding speed on tribological properties of the base alloy and Al-Si alloy–fly ash composites pins on sliding with cast iron disc are evaluated. The wear rate of Al-Si alloy–fly ash composites is lower than that of base alloy, and it increases with increasing load and sliding speed. The coefficient of friction of Al-Si alloy–fly ash composites is increased as compared with base alloy. Practical implications: The development of Al-Si alloy–fly ash composites produced by powder metallurgy technique will modernize the automobile and other industries because near net shape at low cost and good mechanical properties are obtained. Originality/value: There are few papers available on the development and tribological studies of Al-Si alloy–fly ash composites produced by powder metallurgy technique.
- 13 March 2017
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 69 (2) , 241-247
Sliding wear behaviour of Al-Si alloy–fly ash composites produced by powder metallurgy technique
Purpose: Metal matrix composites (MMCs) are commonly used in many aerospace and industrial applications. MMCs possess significantly improved properties including high specific strength, specific modulus, damping capacity and good wear resistance compared to unreinforced alloys. The purpose of this paper is to describe the tribological studies of Al-Si alloy–fly ash composites manufactured using powder metallurgy technique. Design/methodology/approach: Al-Si (12 Wt.%) alloy–fly ash composites were developed using powder metallurgy technique. Al-Si alloy powder was used as matrix material, and the fly ash was used as reinforcement. The particle size of Al-Si alloy powder was in the range of 75-300 μm, and the fly ash was in the range of 1-15 μm. The friction and wear characteristics of the composites were studied using a pin-on-disc set up. The test specimen was mated against cast iron disc, and the tests were conducted with the loads of 10, 20 and 30 N, sliding speeds of 0.5, 1 and 1.5 m/s for a sliding distance of 2,000 m. Findings: The effects of load and sliding speed on tribological properties of the base alloy and Al-Si alloy–fly ash composites pins on sliding with cast iron disc are evaluated. The wear rate of Al-Si alloy–fly ash composites is lower than that of base alloy, and it increases with increasing load and sliding speed. The coefficient of friction of Al-Si alloy–fly ash composites is increased as compared with base alloy. Practical implications: The development of Al-Si alloy–fly ash composites produced by powder metallurgy technique will modernize the automobile and other industries because near net shape at low cost and good mechanical properties are obtained. Originality/value: There are few papers available on the development and tribological studies of Al-Si alloy–fly ash composites produced by powder metallurgy technique.