Charles Sikorsky
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Charles Sikorsky has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Norris Stubbs
Department of Civil Engineering, Texas A&M University, College Station, TX 77843, USA
2 shared publications - Sanghyun Choi
Structural Systems & Site Evaluation Department, Korea Institute of Nuclear Safety, Daejeon 305-600, South Korea
2 shared publications - Sooyong Park
School of Architecture, Youngsan University, Junam-Ri, Ungsang-Up, Yangsan-Si, Kyungnam 626-847, South Korea
2 shared publications - Chia-Ming Uang
Univ. of California
1 shared publication - Hyoung-Bo Sim
Postdoctoral Researcher, Dept. of Structural Engineering, Univ. of California, San Diego, La Jolla, CA 92093-0085
1 shared publication - Robert Bolton
Department of Engineering Technology and Industrial Distribution, Texas A&M University, College Station, TX 77843, USA
1 shared publication
Latest Publications
- 1 September 2009
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 14 (5) , 366-373
Effects of Fabrication Procedures on Fatigue Resistance of Welded Joints in Steel Orthotropic Decks
A common practice for the fabrication of steel orthotropic bridge decks in the United States is to use 80% partial joint penetration (PJP) groove welds between the closed ribs and deck plate. However, it is difficult to eliminate weld melt-through with the thin rib plates. Heat straightening after welding, sometimes combined with precambering, is used to meet the deck plate flatness requirement. To study the effects of both weld melt-through and distortion control measures on the fatigue resistance of the rib-to-deck plate welded joint, six full-scale two-span orthotropic deck specimens were subjected to laboratory testing. Specimens, 10 m long and 3 m wide with four closed ribs, were fabricated with and without weld melt-through and were heat straightened; three specimens were also precambered. To simulate the effect of repetitive truck traffic, each specimen was tested up to 8 million cycles. Test results showed that six cracks initiated from the weld toe outside the rib. Only one crack developed at the...
- 1 September 2009
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 14 (5) , 366-373
Effects of Fabrication Procedures on Fatigue Resistance of Welded Joints in Steel Orthotropic Decks
A common practice for the fabrication of steel orthotropic bridge decks in the United States is to use 80% partial joint penetration (PJP) groove welds between the closed ribs and deck plate. However, it is difficult to eliminate weld melt-through with the thin rib plates. Heat straightening after welding, sometimes combined with precambering, is used to meet the deck plate flatness requirement. To study the effects of both weld melt-through and distortion control measures on the fatigue resistance of the rib-to-deck plate welded joint, six full-scale two-span orthotropic deck specimens were subjected to laboratory testing. Specimens, 10 m long and 3 m wide with four closed ribs, were fabricated with and without weld melt-through and were heat straightened; three specimens were also precambered. To simulate the effect of repetitive truck traffic, each specimen was tested up to 8 million cycles. Test results showed that six cracks initiated from the weld toe outside the rib. Only one crack developed at the...
- 1 November 2004
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 278 (1-2) , 365-381
Periodic monitoring of physical property changes in a concrete box-girder bridge
- 1 November 2004
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 278 (1-2) , 365-381
Periodic monitoring of physical property changes in a concrete box-girder bridge