Yun Soo Lim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yun Soo Lim has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Hong Pyo Kim
Korea Atomic Energy Research Institute
3 shared publications - Seong-Sik Hwang
Nuclear Materials Research Division, Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseong-gu, Daejeon 34057, Korea
3 shared publications Dong Jin Kim
Korea Atomic Energy Research Institute
2 shared publications- Dong-Jin Kim
Department of Environmental Sciences and Biotechnology & Institute of Energy and Environment, Hallym University, 1 Okcheon, Chuncheon, 24251, South Korea
1 shared publication - Dong-Jin Kim
Korea Atomic Energy Research Institute (KAERI)
1 shared publication - Hyoung-Min Jang
Deokyanggas Co., Ltd., 2-13 Nonggong-dangi, Bug-gu, Ulsan 44201, Korea
1 shared publication
Latest Publications
- Open Access
Early-Stage M23C6 Morphology at the Phase Boundary in Type 304L Austenitic Stainless Steel Containing δ Ferrite
The early-stage M23C6 morphology at the phase boundary between austenite and δ ferrite grain in Type 304L austenitic stainless steel was investigated with transmission electron microscopy (TEM). The M23C6 has coherency with austenite grains at phase boundary. The phase boundary between the M23C6 and austenite grains has curved appearance. The curved phase boundary might be a faceted interface composed of (111) plane and the other low-index planes on the atomic scale. The M23C6 morphology at the phase boundary was identified to be a complex pyramid-like shape that has {111}, {110} and {100} interfaces. The slight deviation in the angle measured between edges of carbide in the TEM images from that calculated between edges expected from the M23C6 morphology might be attributed to multilayer growth in the interior region of the M23C6 face.
Open AccessEarly-Stage M23C6 Morphology at the Phase Boundary in Type 304L Austenitic Stainless Steel Containing δ Ferrite
The early-stage M23C6 morphology at the phase boundary between austenite and δ ferrite grain in Type 304L austenitic stainless steel was investigated with transmission electron microscopy (TEM). The M23C6 has coherency with austenite grains at phase boundary. The phase boundary between the M23C6 and austenite grains has curved appearance. The curved phase boundary might be a faceted interface composed of (111) plane and the other low-index planes on the atomic scale. The M23C6 morphology at the phase boundary was identified to be a complex pyramid-like shape that has {111}, {110} and {100} interfaces. The slight deviation in the angle measured between edges of carbide in the TEM images from that calculated between edges expected from the M23C6 morphology might be attributed to multilayer growth in the interior region of the M23C6 face.
- 20 September 2017
- Published by Taylor & Francis
- p. 81-95
6 Stochastic approach to electrochemical noise analysis of SCC of Alloy 600 SG tube in caustic environments at high temperature*
Growth of thermally formed oxides, dissolution of oxides and deposition of corrosion products play an important role in the performance of power cycles. Regarding the secondary side of PWR plants, corrosion concerns are typically associated with the integrity of the steam generator. Localised forms of corrosion in crevices and under deposits are considered to be potentially hazardous and are directly related to secondary circuit chemistry. The contribution of in-situ applied electrochemical techniques, especially corrosion potential and polarisation measurements, for corrosion studies in the light water reactor environment is covered in the comprehensive review of Turnbull and Psaila-Dombrowski [1]. AC techniques can provide additional information about the electronic properties and morphology of the oxide layer and about charge and mass transfer phenomena [2]. New techniques such as contact resistance (CR) or contact electrical impedance (CEI) [3] enable in-situ estimation of oxide resistivity, while controlled distance electrochemistry (CDE) and its derivative thin layer electrochemical impedance spectroscopy (TLEIS) allow for electrochemical measurements in high resistivity media such as boiling water reactor (BWR) coolant [4]. Electrochemical noise (EN) is another prospective electrochemical technique employed for characterisation of corrosion phenomena in the high-temperature environment. EN measurements were used, for example, to detect stress corrosion cracking initiation in BWR media [5].
- 20 September 2017
- Published by Taylor & Francis
- p. 81-95
6 Stochastic approach to electrochemical noise analysis of SCC of Alloy 600 SG tube in caustic environments at high temperature*
Growth of thermally formed oxides, dissolution of oxides and deposition of corrosion products play an important role in the performance of power cycles. Regarding the secondary side of PWR plants, corrosion concerns are typically associated with the integrity of the steam generator. Localised forms of corrosion in crevices and under deposits are considered to be potentially hazardous and are directly related to secondary circuit chemistry. The contribution of in-situ applied electrochemical techniques, especially corrosion potential and polarisation measurements, for corrosion studies in the light water reactor environment is covered in the comprehensive review of Turnbull and Psaila-Dombrowski [1]. AC techniques can provide additional information about the electronic properties and morphology of the oxide layer and about charge and mass transfer phenomena [2]. New techniques such as contact resistance (CR) or contact electrical impedance (CEI) [3] enable in-situ estimation of oxide resistivity, while controlled distance electrochemistry (CDE) and its derivative thin layer electrochemical impedance spectroscopy (TLEIS) allow for electrochemical measurements in high resistivity media such as boiling water reactor (BWR) coolant [4]. Electrochemical noise (EN) is another prospective electrochemical technique employed for characterisation of corrosion phenomena in the high-temperature environment. EN measurements were used, for example, to detect stress corrosion cracking initiation in BWR media [5].
- 30 June 2016
- Published by Korean Society of Pressure Vessels and Piping in Transactions of the Korean Society of Pressure Vessels and Piping
- Vol. 12 (1) , 1-10
Material degradation and its management of reactor internals in PWR
- 30 June 2016
- Published by Korean Society of Pressure Vessels and Piping in Transactions of the Korean Society of Pressure Vessels and Piping
- Vol. 12 (1) , 1-10
Material degradation and its management of reactor internals in PWR
- 31 August 2012
- Published by The Corrosion Science Society of Korea in Corrosion Science and Technology
- Vol. 11 (4) , 141-150
Oxidation Behavior around the Stress Corrosion Crack Tips of Alloy 600 under PWR Primary Water Environment
- 31 August 2012
- Published by The Corrosion Science Society of Korea in Corrosion Science and Technology
- Vol. 11 (4) , 141-150
Oxidation Behavior around the Stress Corrosion Crack Tips of Alloy 600 under PWR Primary Water Environment