Hong Pyo Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hong Pyo Kim has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Seong-Sik Hwang
Nuclear Materials Research Division, Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseong-gu, Daejeon 34057, Korea
7 shared publications - Dong-Jin Kim
Department of Environmental Sciences and Biotechnology & Institute of Energy and Environment, Hallym University, 1 Okcheon, Chuncheon, 24251, South Korea
4 shared publications - Joung Soo Kim
Korea Atomic Energy Research Institute
4 shared publications Sung-Woo Kim
Korea Atomic Energy Research Institute
4 shared publicationsSeong Sik Hwang
Korea Atomic Energy Research Institute
3 shared publications- Yun Soo Lim
Korea Atomic Energy Research Institute
3 shared publications
Latest Publications
- 9 April 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (1) , 49-52
Fractography of Stress Corrosion Cracking of 20% Cold Worked Type 304 H Stainless Steel Containing δ-Ferrite in Oxidizing Primary Water
Fractography of stress corrosion cracking (SCC) of 20% cold worked Type 304 H stainless steel containing δ-ferrite was studied using a compact tension (CT) specimen in oxidizing primary water with a scanning electron microscope (SEM) and electron back scattered diffraction (EBSD). The stress corrosion crack propagated mostly in transgranular stress corrosion cracking (TGSCC) mode and sometimes in intergranular stress corrosion cracking (IGSCC) mode. TGSCC paths were along the {111} plane with both high resolved shear stress and high resolved tensile stress. IGSCC preferentially propagated along the grain boundary perpendicular to the loading axis. The findings in this work suggest that TGSCC proceeds through formation of a weakening zone at the head of the crack tip by interaction of slip and corrosion and then cracking of the weakened zone by tensile stress.
- 9 April 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (1) , 49-52
Fractography of Stress Corrosion Cracking of 20% Cold Worked Type 304 H Stainless Steel Containing δ-Ferrite in Oxidizing Primary Water
Fractography of stress corrosion cracking (SCC) of 20% cold worked Type 304 H stainless steel containing δ-ferrite was studied using a compact tension (CT) specimen in oxidizing primary water with a scanning electron microscope (SEM) and electron back scattered diffraction (EBSD). The stress corrosion crack propagated mostly in transgranular stress corrosion cracking (TGSCC) mode and sometimes in intergranular stress corrosion cracking (IGSCC) mode. TGSCC paths were along the {111} plane with both high resolved shear stress and high resolved tensile stress. IGSCC preferentially propagated along the grain boundary perpendicular to the loading axis. The findings in this work suggest that TGSCC proceeds through formation of a weakening zone at the head of the crack tip by interaction of slip and corrosion and then cracking of the weakened zone by tensile stress.
- Open Access
Early-Stage M23C6 Morphology at the Phase Boundary in Type 304L Austenitic Stainless Steel Containing δ Ferrite
The early-stage M23C6 morphology at the phase boundary between austenite and δ ferrite grain in Type 304L austenitic stainless steel was investigated with transmission electron microscopy (TEM). The M23C6 has coherency with austenite grains at phase boundary. The phase boundary between the M23C6 and austenite grains has curved appearance. The curved phase boundary might be a faceted interface composed of (111) plane and the other low-index planes on the atomic scale. The M23C6 morphology at the phase boundary was identified to be a complex pyramid-like shape that has {111}, {110} and {100} interfaces. The slight deviation in the angle measured between edges of carbide in the TEM images from that calculated between edges expected from the M23C6 morphology might be attributed to multilayer growth in the interior region of the M23C6 face.
Open AccessEarly-Stage M23C6 Morphology at the Phase Boundary in Type 304L Austenitic Stainless Steel Containing δ Ferrite
The early-stage M23C6 morphology at the phase boundary between austenite and δ ferrite grain in Type 304L austenitic stainless steel was investigated with transmission electron microscopy (TEM). The M23C6 has coherency with austenite grains at phase boundary. The phase boundary between the M23C6 and austenite grains has curved appearance. The curved phase boundary might be a faceted interface composed of (111) plane and the other low-index planes on the atomic scale. The M23C6 morphology at the phase boundary was identified to be a complex pyramid-like shape that has {111}, {110} and {100} interfaces. The slight deviation in the angle measured between edges of carbide in the TEM images from that calculated between edges expected from the M23C6 morphology might be attributed to multilayer growth in the interior region of the M23C6 face.
- 7 October 2017
- Published by Springer Nature
- p. 501-507
Relationship Among Dislocation Density, Local Strain Distribution, and PWSCC Susceptibility of Alloy 690
- 7 October 2017
- Published by Springer Nature
- p. 501-507
Relationship Among Dislocation Density, Local Strain Distribution, and PWSCC Susceptibility of Alloy 690
- 20 September 2017
- Published by Taylor & Francis
- p. 81-95
6 Stochastic approach to electrochemical noise analysis of SCC of Alloy 600 SG tube in caustic environments at high temperature*
Growth of thermally formed oxides, dissolution of oxides and deposition of corrosion products play an important role in the performance of power cycles. Regarding the secondary side of PWR plants, corrosion concerns are typically associated with the integrity of the steam generator. Localised forms of corrosion in crevices and under deposits are considered to be potentially hazardous and are directly related to secondary circuit chemistry. The contribution of in-situ applied electrochemical techniques, especially corrosion potential and polarisation measurements, for corrosion studies in the light water reactor environment is covered in the comprehensive review of Turnbull and Psaila-Dombrowski [1]. AC techniques can provide additional information about the electronic properties and morphology of the oxide layer and about charge and mass transfer phenomena [2]. New techniques such as contact resistance (CR) or contact electrical impedance (CEI) [3] enable in-situ estimation of oxide resistivity, while controlled distance electrochemistry (CDE) and its derivative thin layer electrochemical impedance spectroscopy (TLEIS) allow for electrochemical measurements in high resistivity media such as boiling water reactor (BWR) coolant [4]. Electrochemical noise (EN) is another prospective electrochemical technique employed for characterisation of corrosion phenomena in the high-temperature environment. EN measurements were used, for example, to detect stress corrosion cracking initiation in BWR media [5].
- 20 September 2017
- Published by Taylor & Francis
- p. 81-95
6 Stochastic approach to electrochemical noise analysis of SCC of Alloy 600 SG tube in caustic environments at high temperature*
Growth of thermally formed oxides, dissolution of oxides and deposition of corrosion products play an important role in the performance of power cycles. Regarding the secondary side of PWR plants, corrosion concerns are typically associated with the integrity of the steam generator. Localised forms of corrosion in crevices and under deposits are considered to be potentially hazardous and are directly related to secondary circuit chemistry. The contribution of in-situ applied electrochemical techniques, especially corrosion potential and polarisation measurements, for corrosion studies in the light water reactor environment is covered in the comprehensive review of Turnbull and Psaila-Dombrowski [1]. AC techniques can provide additional information about the electronic properties and morphology of the oxide layer and about charge and mass transfer phenomena [2]. New techniques such as contact resistance (CR) or contact electrical impedance (CEI) [3] enable in-situ estimation of oxide resistivity, while controlled distance electrochemistry (CDE) and its derivative thin layer electrochemical impedance spectroscopy (TLEIS) allow for electrochemical measurements in high resistivity media such as boiling water reactor (BWR) coolant [4]. Electrochemical noise (EN) is another prospective electrochemical technique employed for characterisation of corrosion phenomena in the high-temperature environment. EN measurements were used, for example, to detect stress corrosion cracking initiation in BWR media [5].
- Open Access
- 1 June 2017
- Published by Walter de Gruyter GmbH in Archives of Metallurgy and Materials
- Vol. 62 (2) , 1415-1419
Effects of Grain Boundary Morphologies on Stress Corrosion Cracking of Alloy 600
Effects of grain boundary morphologies on stress corrosion cracking (SCC) of Alloy 600 have been studied in 40% NaOH at 315°C using C-ring specimens. The configuration of the grain boundary and the intergranular carbide density were controlled by heat treatment. SCC tests were performed at +150 mV above the corrosion potential. The specimen with a serrated grain boundary showed higher SCC resistance than that with a straight grain boundary. This appears to be caused by the fact that the specimen with the serrated grain boundary has longer SCC path. SCC resistance also increased with intergranular carbide density probably due to enhanced relaxation of stress at intergranular carbide.
- 1 June 2017
- Published by Walter de Gruyter GmbH in Archives of Metallurgy and Materials
- Vol. 62 (2) , 1415-1419
Open AccessEffects of Grain Boundary Morphologies on Stress Corrosion Cracking of Alloy 600
Effects of grain boundary morphologies on stress corrosion cracking (SCC) of Alloy 600 have been studied in 40% NaOH at 315°C using C-ring specimens. The configuration of the grain boundary and the intergranular carbide density were controlled by heat treatment. SCC tests were performed at +150 mV above the corrosion potential. The specimen with a serrated grain boundary showed higher SCC resistance than that with a straight grain boundary. This appears to be caused by the fact that the specimen with the serrated grain boundary has longer SCC path. SCC resistance also increased with intergranular carbide density probably due to enhanced relaxation of stress at intergranular carbide.
- 30 June 2014
- Published by The Corrosion Science Society of Korea in Corrosion Science and Technology
- Vol. 13 (3) , 112-119
Laboratorial technique for fabrication of outer diameter stress corrosion cracking on steam generator tubing
- 30 June 2014
- Published by The Corrosion Science Society of Korea in Corrosion Science and Technology
- Vol. 13 (3) , 112-119
Laboratorial technique for fabrication of outer diameter stress corrosion cracking on steam generator tubing
- 1 February 2014
- Published by Bentham Science Publishers Ltd. in Current Nanoscience
- Vol. 10 (1) , 81-85
Relation between Surface Oxide and SCC of Alloy 600
Abstract: Stress corrosion cracking (SCC) is one of major threats against the integrity of the structural materials composing a nuclear power plant (NPP). Lead is deleterious element accelerating the SCC of Alloy 600 used as a steam generator tubing material in an NPP. In the present work, the oxide property grown on an Alloy 600 surface was evaluated as a function of PbO content using electrochemical impedance spectroscopy (EIS) and a field-emission transmission electron microscopy, equipped with an energy dispersive X-ray spectroscopy (TEM –EDS) for the specimen prepared using a focused ion beam (FIB). Alloy 600 was immersed in 0.1M NaOH containing PbO in the range of 0-5,000 ppm at 315oC for 2 weeks. The oxide property was compared with SCC susceptibility obtained from a slow strain rate tension (SSRT) test for Alloy 600 in 0.1M NaOH containing PbO. The impedance value was greatly decreased by adding PbO into the solution indicating a decrease in passivity. The composition of the oxide was also changed by Pb in an aqueous solution. The duplex oxide layer consisting of outer porous nickel-rich oxide and inner dense chromium-rich oxide is modified to a Pb incorporated nickel-rich oxide layer. Modification of the oxide property induced by lead incorporation caused an obvious increase in SCC susceptibility. It is expected that lead observed at the crack tip of an early cracked pulled Alloy 600TT tube was considerably responsible for SCC acceleration of this tube among numerous sound tubes in an NPP.
- 1 February 2014
- Published by Bentham Science Publishers Ltd. in Current Nanoscience
- Vol. 10 (1) , 81-85
Relation between Surface Oxide and SCC of Alloy 600
Abstract: Stress corrosion cracking (SCC) is one of major threats against the integrity of the structural materials composing a nuclear power plant (NPP). Lead is deleterious element accelerating the SCC of Alloy 600 used as a steam generator tubing material in an NPP. In the present work, the oxide property grown on an Alloy 600 surface was evaluated as a function of PbO content using electrochemical impedance spectroscopy (EIS) and a field-emission transmission electron microscopy, equipped with an energy dispersive X-ray spectroscopy (TEM –EDS) for the specimen prepared using a focused ion beam (FIB). Alloy 600 was immersed in 0.1M NaOH containing PbO in the range of 0-5,000 ppm at 315oC for 2 weeks. The oxide property was compared with SCC susceptibility obtained from a slow strain rate tension (SSRT) test for Alloy 600 in 0.1M NaOH containing PbO. The impedance value was greatly decreased by adding PbO into the solution indicating a decrease in passivity. The composition of the oxide was also changed by Pb in an aqueous solution. The duplex oxide layer consisting of outer porous nickel-rich oxide and inner dense chromium-rich oxide is modified to a Pb incorporated nickel-rich oxide layer. Modification of the oxide property induced by lead incorporation caused an obvious increase in SCC susceptibility. It is expected that lead observed at the crack tip of an early cracked pulled Alloy 600TT tube was considerably responsible for SCC acceleration of this tube among numerous sound tubes in an NPP.
- 12 September 2013
- Published by Springer Nature in Journal of Solid State Electrochemistry
- Vol. 18 (2) , 309-323
Ex situ and in situ characterization of stress corrosion cracking of nickel-base alloys at high temperature
- 12 September 2013
- Published by Springer Nature in Journal of Solid State Electrochemistry
- Vol. 18 (2) , 309-323
Ex situ and in situ characterization of stress corrosion cracking of nickel-base alloys at high temperature
- 1 September 2013
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 440 (1-3) , 129-135
SCC analysis of Alloy 600 tubes from a retired steam generator
- 1 September 2013
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 440 (1-3) , 129-135
SCC analysis of Alloy 600 tubes from a retired steam generator
- 30 April 2013
- Published by The Corrosion Science Society of Korea in Corrosion Science and Technology
- Vol. 12 (2) , 93-101
Study on Localized Corrosion Cracking of Alloy 600 using EN-DCPD Technique
- 30 April 2013
- Published by The Corrosion Science Society of Korea in Corrosion Science and Technology
- Vol. 12 (2) , 93-101
Study on Localized Corrosion Cracking of Alloy 600 using EN-DCPD Technique