Hamza Kemal Akyildiz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hamza Kemal Akyildiz has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Haydar Livatyali
Department of Mechatronics Engineering, Yildiz Technical University
3 shared publications - Kazim Ercan
Yozgat Bozok University, College of Engineering, Mechanical Engineering Department, Yozgat, Turkey
1 shared publication - Mehmet Akif Dundar
Yozgat Bozok Üniversitesi
1 shared publication
Latest Publications
- 1 December 2024
- Published by Pleiades Publishing Ltd in Mechanics of Solids
- Vol. 59 (8) , 3968-3984
Investigating the Flexural Behavior of Ultra-High-Molecular-Weight Polyethylene at a Low Bending Rate: Experimental and Numerical Study
This study examines the mechanical behavior of ultra-high-molecular-weight polyethylene (UHMWPE) under three-point bending at a low strain rate, with a particular focus on evaluating the influence of its distinct tensile and compressive properties on its bending response through finite element analysis. The tensile and compressive stress-strain characteristics of UHMWPE were experimentally determined at a strain rate of 5 × 10−3 s–1, complemented by three-point bending tests conducted at a constant loading speed of 0.05 mm/s. To predict the flexural behavior of UHMWPE, two finite element models were constructed using the SAMP-1 material model in LS-DYNA: one incorporating the Von-Mises yield surface, which assumes similar material behavior in tension and compression, and the other employing the Drucker-Prager yield surface, which accounts for dissimilar material behaviors between tension and compression. Results of the numerical analyses revealed substantial discrepancies between the predictions of the Von-Mises and Drucker-Prager models, with the latter offering a more precise prediction of the flexural response of UHMWPE, thereby underscoring the critical importance of accounting for dissimilar material behaviors to achieve enhanced predictive accuracy.
- 1 December 2024
- Published by Pleiades Publishing Ltd in Mechanics of Solids
- Vol. 59 (8) , 3968-3984
Investigating the Flexural Behavior of Ultra-High-Molecular-Weight Polyethylene at a Low Bending Rate: Experimental and Numerical Study
This study examines the mechanical behavior of ultra-high-molecular-weight polyethylene (UHMWPE) under three-point bending at a low strain rate, with a particular focus on evaluating the influence of its distinct tensile and compressive properties on its bending response through finite element analysis. The tensile and compressive stress-strain characteristics of UHMWPE were experimentally determined at a strain rate of 5 × 10−3 s–1, complemented by three-point bending tests conducted at a constant loading speed of 0.05 mm/s. To predict the flexural behavior of UHMWPE, two finite element models were constructed using the SAMP-1 material model in LS-DYNA: one incorporating the Von-Mises yield surface, which assumes similar material behavior in tension and compression, and the other employing the Drucker-Prager yield surface, which accounts for dissimilar material behaviors between tension and compression. Results of the numerical analyses revealed substantial discrepancies between the predictions of the Von-Mises and Drucker-Prager models, with the latter offering a more precise prediction of the flexural response of UHMWPE, thereby underscoring the critical importance of accounting for dissimilar material behaviors to achieve enhanced predictive accuracy.
- 18 September 2013
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 70 (1-4) , 547-557
Effect of cutting energy on fatigue behavior of threaded specimens
- 18 September 2013
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 70 (1-4) , 547-557
Effect of cutting energy on fatigue behavior of threaded specimens
- 17 July 2013
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 135 (4) , 041004
Design of Threaded Fatigue Test Specimen for Machining
Design and machining of the fatigue test specimens have significant effects on the duration and reliability of fatigue test. Fatigue test specimens essentially consist of three parts: the center or critical test section, which is the region where required conditions are simulated as closely as possible, and the two ends, which serve to transfer the load from the grips to the center section. When high strength materials are used for a complex geometry, such as a thread need to be tested, design and manufacturing of the specimens become more influential on the reliability and duration of the tests. Threaded fatigue test specimens were designed, machined, and tested in a four-point rotary bending fatigue testing machine. An innovative threaded fatigue test specimen that consistently fails at the critical test section was designed, machined, and tested successfully to give the required fatigue notch factor. Because of full scale fatigue testing with threaded parts is very expensive and sometimes dangerous, evaluated threaded fatigue specimen can be used in fatigue testing and it reduces duration of the experiment more than 60% for machined threaded specimens.
- 17 July 2013
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 135 (4) , 041004
Design of Threaded Fatigue Test Specimen for Machining
Design and machining of the fatigue test specimens have significant effects on the duration and reliability of fatigue test. Fatigue test specimens essentially consist of three parts: the center or critical test section, which is the region where required conditions are simulated as closely as possible, and the two ends, which serve to transfer the load from the grips to the center section. When high strength materials are used for a complex geometry, such as a thread need to be tested, design and manufacturing of the specimens become more influential on the reliability and duration of the tests. Threaded fatigue test specimens were designed, machined, and tested in a four-point rotary bending fatigue testing machine. An innovative threaded fatigue test specimen that consistently fails at the critical test section was designed, machined, and tested successfully to give the required fatigue notch factor. Because of full scale fatigue testing with threaded parts is very expensive and sometimes dangerous, evaluated threaded fatigue specimen can be used in fatigue testing and it reduces duration of the experiment more than 60% for machined threaded specimens.
- 19 April 2013
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 68 (5-8) , 1601-1612
Evaluating of cutting forces in thread machining
- 19 April 2013
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 68 (5-8) , 1601-1612
Evaluating of cutting forces in thread machining
- 1 October 2011
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 15 (4) , 485-506
PREDICTION AND EXPERIMENTAL ANALYSIS OF CUTTING FORCES DURING MACHINING OF PRECISION EXTERNAL THREADS
External thread cutting is a complex 3-D process in which the cutting conditions vary over the thread cutter profile. It is accepted as a mature; however, heavily experience based technology and there are few academic work published. Determining the cutting forces during machining is crucial to explain formation of the surface layer, residual stresses, selection of the most appropriate machine tool and optimizing the process. This investigation is an attempt to predict thread cutting forces by dividing the thread chip into three parts, one thread root and two side faces. Variation of the cutting parameters including the shear angle, mean cutting temperature and friction force on the flank face of the tool along the thread tool root and sides are determined. In the thread root and sides, chip compression ratios for the V-shaped single piece and separately cut chip zones are measured and cutting forces are calculated and compared for precision metric thread cutting on a SAE 4340 steel bar.
- 1 October 2011
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 15 (4) , 485-506
PREDICTION AND EXPERIMENTAL ANALYSIS OF CUTTING FORCES DURING MACHINING OF PRECISION EXTERNAL THREADS
External thread cutting is a complex 3-D process in which the cutting conditions vary over the thread cutter profile. It is accepted as a mature; however, heavily experience based technology and there are few academic work published. Determining the cutting forces during machining is crucial to explain formation of the surface layer, residual stresses, selection of the most appropriate machine tool and optimizing the process. This investigation is an attempt to predict thread cutting forces by dividing the thread chip into three parts, one thread root and two side faces. Variation of the cutting parameters including the shear angle, mean cutting temperature and friction force on the flank face of the tool along the thread tool root and sides are determined. In the thread root and sides, chip compression ratios for the V-shaped single piece and separately cut chip zones are measured and cutting forces are calculated and compared for precision metric thread cutting on a SAE 4340 steel bar.