Marc Vantorre
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Marc Vantorre has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Guillaume Delefortrie
Flanders Hydraulics Research
6 shared publications - Wim Van Hoydonck
Flanders Hydraulics, Berchemlei 115, 2140 Antwerp, Belgium
3 shared publications - Evert Lataire
Department of Civil Engineering, Maritime Technology Division, Ghent University, Zwijnaarde, Belgium
2 shared publications - Katrien Eloot
Flanders Hydraulics
2 shared publications - Peter Troch
Department of Civil Engineering, Ghent University, Technologiepark 60, 9052 Ghent, Belgium
2 shared publications - Timothy Vervaet
Department of Civil Engineering, Ghent University, Technologiepark 60, B-9052 Zwijnaarde, Belgium
2 shared publications
Latest Publications
- 27 January 2024
- Published by Elsevier in Ocean Engineering
- Vol. 294
Experimental and numerical study of the hydrodynamic forces acting on a surface-piercing hydrofoil in muddy environments
- 27 January 2024
- Published by Elsevier in Ocean Engineering
- Vol. 294
Experimental and numerical study of the hydrodynamic forces acting on a surface-piercing hydrofoil in muddy environments
- Open Access
- 11 October 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (10) , 1480
Experimental Modelling of an Isolated WECfarm Real-Time Controllable Heaving Point Absorber Wave Energy Converter
To offer point absorber wave energy converters (WECs) as a bankable product on the marine renewable energy market, multiple WECs will be installed together in an array configuration. The wave energy community (research and industrial) has identified the urgent need for available realistic and reliable data on WEC array tests in order to perform a better WEC array optimization approach and in order to validate recently developed (non-linear) numerical models. The ‘WECfarm’ project is initiated to cover this scientific gap on necessary experimental data. The ‘WECfarm’ experimental setup consists of an array of five generic heaving point-absorber WECs. The WECs are equipped with a permanent magnet synchronous motor (PMSM), addressing the need for WEC array tests with an accurate and actively controllable power take-off (PTO). The WEC array control and data acquisition are realized with a Speedgoat Performance real-time target machine, offering the possibility to implement advanced WEC array control strategies in the MATLAB-Simulink environment. The presented article describes the experimental setup, the performed tests and the results of the test campaign using a single, isolated ‘WECfarm’ WEC in April 2021 at the wave basin of Aalborg University (AAU), Denmark. A Coulomb and viscous friction model is determined to partly compensate for the drivetrain (motor, gearbox, rack and pinion) friction. A system identification (SID) approach is adopted considering the WEC system to be composed of two single input single output (SISO) models, the radiation and the excitation model. Radiation tests yield the intrinsic impedance. Excitation tests yield the excitation frequency response function. Adopting an impedance matching approach, the control parameters for the resistive and reactive controller are determined from the complex conjugate of the intrinsic impedance. Both controllers are tested for a selection of regular wave conditions. The performed experimental test campaign using an isolated ‘WECfarm’ WEC allows a full evaluation of the WEC design prior to extending the setup to five WECs. Within the ‘WECfarm’ project, an experimental campaign with a five-WEC array in the Coastal and Ocean Basin (COB) in Ostend, Belgium, is under preparation.
- 11 October 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (10) , 1480
Open AccessExperimental Modelling of an Isolated WECfarm Real-Time Controllable Heaving Point Absorber Wave Energy Converter
To offer point absorber wave energy converters (WECs) as a bankable product on the marine renewable energy market, multiple WECs will be installed together in an array configuration. The wave energy community (research and industrial) has identified the urgent need for available realistic and reliable data on WEC array tests in order to perform a better WEC array optimization approach and in order to validate recently developed (non-linear) numerical models. The ‘WECfarm’ project is initiated to cover this scientific gap on necessary experimental data. The ‘WECfarm’ experimental setup consists of an array of five generic heaving point-absorber WECs. The WECs are equipped with a permanent magnet synchronous motor (PMSM), addressing the need for WEC array tests with an accurate and actively controllable power take-off (PTO). The WEC array control and data acquisition are realized with a Speedgoat Performance real-time target machine, offering the possibility to implement advanced WEC array control strategies in the MATLAB-Simulink environment. The presented article describes the experimental setup, the performed tests and the results of the test campaign using a single, isolated ‘WECfarm’ WEC in April 2021 at the wave basin of Aalborg University (AAU), Denmark. A Coulomb and viscous friction model is determined to partly compensate for the drivetrain (motor, gearbox, rack and pinion) friction. A system identification (SID) approach is adopted considering the WEC system to be composed of two single input single output (SISO) models, the radiation and the excitation model. Radiation tests yield the intrinsic impedance. Excitation tests yield the excitation frequency response function. Adopting an impedance matching approach, the control parameters for the resistive and reactive controller are determined from the complex conjugate of the intrinsic impedance. Both controllers are tested for a selection of regular wave conditions. The performed experimental test campaign using an isolated ‘WECfarm’ WEC allows a full evaluation of the WEC design prior to extending the setup to five WECs. Within the ‘WECfarm’ project, an experimental campaign with a five-WEC array in the Coastal and Ocean Basin (COB) in Ostend, Belgium, is under preparation.
- Open Access
- 2 August 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (8) , 1062
Experimental Modelling of Point-Absorber Wave Energy Converter Arrays: A Comprehensive Review, Identification of Research Gaps and Design of the WECfarm Setup
Commercial wave energy exploitation will be realised by placing multiple wave energy converters (WECs) in an array configuration. A point-absorber WEC consists of a floating or submerged body to capture wave energy from different wave directions. This point-absorber WEC acts as an efficient wave absorber that is also an efficient wave generator. Optimising the WEC array layout to obtain constructive interference within the WEC array is theoretically beneficial, whereas for wind farms, it is only important to avoid destructive interference within an array of wind turbines due to wake effects. Moreover, the WEC array layout should be optimised simultaneously with the applied control strategy. This article provides a literature review on the state of the art in physical modelling of point-absorber WEC arrays and the identification of research gaps. To cover the scientific gap of experimental data necessary for the validation of recently developed (nonlinear) numerical models for WEC arrays, Ghent University has introduced the “WECfarm” project. The identified research gaps are translated into design requirements for the “WECfarm” WEC array setup and test matrix. This article presents the design of the “WECfarm” experimental setup, consisting of an array of five generic heaving point-absorber WECs. The WECs are equipped with a permanent magnet synchronous motor (PMSM), addressing the need for WEC array tests with an accurate and actively controllable power take-off (PTO). The WEC array control and data acquisition are realised with a Speedgoat Performance real-time target machine, offering the possibility to implement advanced WEC array control strategies in the MATLAB-Simulink model. Wave basin testing includes long- and short-crested waves and extreme wave conditions, representing real sea conditions. Within the “WECfarm” project, two experimental campaigns were performed at the Aalborg University wave basin: (a) a testing of the first WEC in April 2021 and (b) a testing of a two-WEC array in February 2022. An experimental campaign with a five-WEC array is under preparation at the moment of writing.
- 2 August 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (8) , 1062
Open AccessExperimental Modelling of Point-Absorber Wave Energy Converter Arrays: A Comprehensive Review, Identification of Research Gaps and Design of the WECfarm Setup
Commercial wave energy exploitation will be realised by placing multiple wave energy converters (WECs) in an array configuration. A point-absorber WEC consists of a floating or submerged body to capture wave energy from different wave directions. This point-absorber WEC acts as an efficient wave absorber that is also an efficient wave generator. Optimising the WEC array layout to obtain constructive interference within the WEC array is theoretically beneficial, whereas for wind farms, it is only important to avoid destructive interference within an array of wind turbines due to wake effects. Moreover, the WEC array layout should be optimised simultaneously with the applied control strategy. This article provides a literature review on the state of the art in physical modelling of point-absorber WEC arrays and the identification of research gaps. To cover the scientific gap of experimental data necessary for the validation of recently developed (nonlinear) numerical models for WEC arrays, Ghent University has introduced the “WECfarm” project. The identified research gaps are translated into design requirements for the “WECfarm” WEC array setup and test matrix. This article presents the design of the “WECfarm” experimental setup, consisting of an array of five generic heaving point-absorber WECs. The WECs are equipped with a permanent magnet synchronous motor (PMSM), addressing the need for WEC array tests with an accurate and actively controllable power take-off (PTO). The WEC array control and data acquisition are realised with a Speedgoat Performance real-time target machine, offering the possibility to implement advanced WEC array control strategies in the MATLAB-Simulink model. Wave basin testing includes long- and short-crested waves and extreme wave conditions, representing real sea conditions. Within the “WECfarm” project, two experimental campaigns were performed at the Aalborg University wave basin: (a) a testing of the first WEC in April 2021 and (b) a testing of a two-WEC array in February 2022. An experimental campaign with a five-WEC array is under preparation at the moment of writing.
- 1 September 2021
- Published by Elsevier in Ocean Engineering
- Vol. 235, 109327
6DOF manoeuvring model of KCS with full roll coupling
- 1 September 2021
- Published by Elsevier in Ocean Engineering
- Vol. 235, 109327
6DOF manoeuvring model of KCS with full roll coupling
- 1 June 2021
- Published by Elsevier in Ocean Engineering
- Vol. 230
Hydrodynamic ship–ship and ship–bank interaction: A comparative numerical study
- 1 June 2021
- Published by Elsevier in Ocean Engineering
- Vol. 230
Hydrodynamic ship–ship and ship–bank interaction: A comparative numerical study
- 18 March 2019
- Published by Emerald Publishing in Maritime Business Review
- Vol. 4 (1) , 106-127
Safety of container ship (un)loading operations in the Port of Antwerp
Purpose: Economies of scale drive container ship owners towards ordering larger vessels. Terminals need to ensure a safe (un)loading operation of these vessels, which can only be guaranteed if the mooring equipment is not overloaded (lines, fenders and bollards) and if the motions of the vessel remain below set limits, under external forces. This paper aims to focus on the passing vessel effect as a potential disturbing factor in the Port of Antwerp.Design/methodology/approach: Motion criteria for allowing safe (un)loading of container vessels are established by considering the container handling process and existing international standards (PIANC). A case study simulation is presented where the behaviour of the moored vessel under ship passages is evaluated. Starting from a representative event, the effect of changes in passing speed and distance is discussed.Findings: The study illustrates the influence of passing velocity and distance on the behaviour of the moored vessel, showing that when passing speeds are higher and/or distances lower than the reference event, safety limits are potentially exceeded. Possible mitigating measures, including the use of stiffer mooring lines and/or a change in arrangement, are discussed.Research limitations/implications: This paper serves as a basis for future research on safety criteria and optimisation of the mooring equipment and configuration to deal with passing vessel effects.Practical implications: The presented results can be used by ship and terminal designers to gain familiarity with passing vessel effects and adopt suggested best practice.Social implications: By restricting the motions of the passing vessels, the focus and general well-being of the crane operator is enhanced, as is the safety of workers.Originality/value: The paper provides a unique combination of container fleet observation, safety criteria establishment and case study application.
- 18 March 2019
- Published by Emerald Publishing in Maritime Business Review
- Vol. 4 (1) , 106-127
Safety of container ship (un)loading operations in the Port of Antwerp
Purpose: Economies of scale drive container ship owners towards ordering larger vessels. Terminals need to ensure a safe (un)loading operation of these vessels, which can only be guaranteed if the mooring equipment is not overloaded (lines, fenders and bollards) and if the motions of the vessel remain below set limits, under external forces. This paper aims to focus on the passing vessel effect as a potential disturbing factor in the Port of Antwerp.Design/methodology/approach: Motion criteria for allowing safe (un)loading of container vessels are established by considering the container handling process and existing international standards (PIANC). A case study simulation is presented where the behaviour of the moored vessel under ship passages is evaluated. Starting from a representative event, the effect of changes in passing speed and distance is discussed.Findings: The study illustrates the influence of passing velocity and distance on the behaviour of the moored vessel, showing that when passing speeds are higher and/or distances lower than the reference event, safety limits are potentially exceeded. Possible mitigating measures, including the use of stiffer mooring lines and/or a change in arrangement, are discussed.Research limitations/implications: This paper serves as a basis for future research on safety criteria and optimisation of the mooring equipment and configuration to deal with passing vessel effects.Practical implications: The presented results can be used by ship and terminal designers to gain familiarity with passing vessel effects and adopt suggested best practice.Social implications: By restricting the motions of the passing vessels, the focus and general well-being of the crane operator is enhanced, as is the safety of workers.Originality/value: The paper provides a unique combination of container fleet observation, safety criteria establishment and case study application.
- Open Access
- 1 January 2012
- Published by TU Delft OPEN Publishing in European Journal Of Transport and Infrastructure Research
- Vol. 12 (1)
Probabilistic Regulation for Inland Vessels Operating at Sea as an Alternative Hinterland Connection for Coastal Harbours
In 2007, the Belgian Federal Authorities issued a Royal Decree concerning “inland vessels that can also be utilised for non-international sea voyages”, allowing inland vessels to operate in coastal areas between the Belgian coastal harbours and the Belgian inland waterway network via the Western Scheldt. These new regulations have a unique character due to their probabilistic approach: among other requirements, a risk analysis must demonstrate that the probability of adverse events such as bottom slamming, overtaking of water on deck and ingress of water in open cargo holds is limited to an acceptable level. Several inland vessels (tankers, container vessels, car carriers) are nowadays operating according to this Decree in significant wave heights up to 1.90 m. Background is provided into these present regulations, with emphasis on the probabilistic aspects. A description is given of the methodology used for performing the required risk analyses. The effect of important parameters is discussed, both ship related (metacentric height, bilge keels) and wave climate dependent, and an overview of the ongoing research at Flanders Hydraulics Research and Ghent University on estuary container vessels is given.
- 1 January 2012
- Published by TU Delft OPEN Publishing in European Journal Of Transport and Infrastructure Research
- Vol. 12 (1)
Open AccessProbabilistic Regulation for Inland Vessels Operating at Sea as an Alternative Hinterland Connection for Coastal Harbours
In 2007, the Belgian Federal Authorities issued a Royal Decree concerning “inland vessels that can also be utilised for non-international sea voyages”, allowing inland vessels to operate in coastal areas between the Belgian coastal harbours and the Belgian inland waterway network via the Western Scheldt. These new regulations have a unique character due to their probabilistic approach: among other requirements, a risk analysis must demonstrate that the probability of adverse events such as bottom slamming, overtaking of water on deck and ingress of water in open cargo holds is limited to an acceptable level. Several inland vessels (tankers, container vessels, car carriers) are nowadays operating according to this Decree in significant wave heights up to 1.90 m. Background is provided into these present regulations, with emphasis on the probabilistic aspects. A description is given of the methodology used for performing the required risk analyses. The effect of important parameters is discussed, both ship related (metacentric height, bilge keels) and wave climate dependent, and an overview of the ongoing research at Flanders Hydraulics Research and Ghent University on estuary container vessels is given.
- 25 February 2010
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 15 (2) , 119-130
Bottom slamming on heaving point absorber wave energy devices
- 25 February 2010
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 15 (2) , 119-130
Bottom slamming on heaving point absorber wave energy devices
- 17 March 2009
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 14 (2) , 171-184
Modelling propeller and rudder induced forces acting on deep drafted vessels in muddy navigation areas
- 17 March 2009
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 14 (2) , 171-184
Modelling propeller and rudder induced forces acting on deep drafted vessels in muddy navigation areas
- 3 March 2009
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 14 (1) , 51-68
Prediction of the forces acting on container carriers in muddy navigation areas using a fluidization parameter
- 3 March 2009
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 14 (1) , 51-68
Prediction of the forces acting on container carriers in muddy navigation areas using a fluidization parameter