VSVladimir Segal

Vladimir Segal

*This is an algorithmically generated author record based on publicly available information.

Vladimir Segal has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Equal-Channel Angular Extrusion (ECAE): From a Laboratory Curiosity to an Industrial Technology

    by Vladimir Segal

    This paper presents a state-of-the-art and a retrospective view of the critical stages in the evolution of equal-channel angular extrusion (ECAE) from the original idea to a cost-effective industrial technology. These stages include optimization of the structure modification and material processing, development of the special tools, process commercialization, and a large-scale validation of the semi-continuous ECAE at the industrial floor. All aspects are extensively summarized, based on the author’s experience in the field, which spans almost half of a century. Special attention is paid to the processing of large batch billets. Practical examples illustrate industrial applications of ECAE. The scope for future development is also discussed.


  • Open Access

    Semi-Continuous Equal-Channel Angular Extrusion and Rolling of AA5083 and AZ31 Alloys

    by Vladimir Segal, Svetlana V. Reznikov, Nagendra Murching, Vincent H. Hammond, Laszlo J. Kecskes

    This paper describes a new modification of equal-channel angular extrusion for the “pass-by-pass” semi-continuous (sc-ECAE) processing of lightweight alloys. Sc-ECAE leads to a multifold increase in productivity and decrease in costs, providing a technical basis for the commercialization of severe plastic deformation (SPD) on a large scale with massive volume production. The evolution of the structure and properties are analyzed for an aluminum alloy (AA) 5083 and a magnesium alloy AZ31 as model materials representing, respectively, the structural refinement under severe plastic deformation (SPD) via strain-induced formation of new grain boundaries and via dynamic recrystallization. For the first alloy, the microstructure after sc-ECAE is formed via ultrafine sub-grains, which are further transformed into sub-micrometer grains during post-ECAE rolling. The preliminary solution treatment of AA5083 is an important stabilizing factor for the achievement of high mechanical properties. For the second alloy, optimized sc-ECAE results in a remarkable structural refinement, and a good balance of properties is obtained with a low number of passes. However, additional rolling in the latter case leads to a degradation of the structure and properties.


  • Equivalent and effective strains during severe plastic deformation (SPD)

    by V. M. Segal

    This paper considers the characteristics of severe plastic deformation (SPD) to estimate its efficacy and to compare different processing techniques. In contrast to effective strains by von Mises and Hencky, the rotation component of the strain rate is included in the analysis as a mode of deformation, which ranges from simple shear to pure shear. Distortions of material elements during a uniform plane plastic flow are calculated using a kinematic approach. For the fixed deformation mode, the current state is defined by the accumulated shears that are identical to the von Mises effective shear strains. In specific cases of pure shear and simple shear, the accumulated shears match the specific distortions of round or square elements prescribed by Hencky or von Mises approach, respectively. The mode of deformation is important to the structural effects of SPD. In general, two separated characteristics, accumulated shear and the coefficient of deformation mode, are necessary to describe strains during SPD.


  • Top Cited Papers
    Open Access

    Review: Modes and Processes of Severe Plastic Deformation (SPD)

    by Vladimir Segal

    In this review, severe plastic deformation (SPD) is considered as a materials processing technology. The deformation mode is the principal characteristic differentiating SPD techniques from common forming operations. For large plastic strains, deformation mode depends on the distribution of strain rates between continuum slip lines and can be varied from pure shear to simple shear. A scalar, invariant, and dimensionless coefficient of deformation mode is introduced as a normalized speed of rigid rotation. On this basis, simple shear provides the optimal mode for structure modification and grain refinement, whereas pure shear is “ideal” for forming operations. Special experiments and SPD practice confirm this conclusion. Various techniques of SPD are classified and described in accordance with simple shear realization or approximation. It is shown that correct analyses of the processing mechanics and technological parameters are essential for the comparison of SPD techniques and the development of effective industrial technologies.